User's Manual

Notes for battery disposal
The batteries used with this product contain chemicals that
are harmful to the environment. To preserve our environment,
dispose of used batteries according to your local laws or
regulations. Do not dispose of batteries with normal household
waste.
For more information, please contact the local authority or your
retailer where you purchased the product.
EN
Safety Warnings
- Read all the instructions carefully before using the unit and
keep them for future reference.
- Retain the manual. If you pass the unit onto a third party
make sure to include this manual.
- The product complies with the requirement of the
1999/5/EC directive.
Damage
- Please inspect the unit for damage after unpacking.
- Do not continue to operate the unit if you are in any doubt
about it working normally, or if it is damaged in any way -
switch off, withdraw the mains plug and consult your dealer.
Location of Unit
 7KHXQLWPXVWEHSODFHGRQDÀDWVWDEOHVXUIDFHDQGVKRXOG
not be subjected to vibrations.
- Do not place the unit on sloped or unstable surfaces as the
unit may fall off or tip over.
- The mains socket must be located near the unit and should
be easily accessible.
Temperature
- Avoid extreme degrees of temperature, either hot or cold.
Place the unit well away from heat sources such as
 UDGLDWRUVRUJDVHOHFWULF¿UHV
- Avoid exposure to direct sunlight and other sources of heat.
Naked Flames
 1HYHUSODFHDQ\W\SHRIFDQGOHRUQDNHGÀDPHRQWKHWRSRI
or near the unit.
Moisture
- 7RUHGXFHWKHULVNRI¿UHHOHFWULFVKRFNRUSURGXFWGDPDJH
do not expose this unit to rain, moisture, dripping or
 VSODVKLQJ1RREMHFWV¿OOHGZLWKOLTXLGVVXFKDVYDVHV
should be placed on the unit.
- If you spill any liquid into the unit, it can cause serious
damages. Switch it off at the mains immediately. Withdraw
the mains plug and consult your dealer.
Ventilation
- 7RSUHYHQWWKHULVNRIHOHFWULFVKRFNRU¿UHKD]DUGGXHWR
overheating, ensure that curtains and other materials do not
obstruct the ventilation vents.
- A minimum distance of 5cm around the unit should be
 PDLQWDLQHGWRDOORZIRUVXI¿FLHQWYHQWLODWLRQ
- Do not install or place this unit in a bookcase, built-in
 FDELQHWRULQDQRWKHUFRQ¿QHGVSDFH(QVXUHWKHXQLWLVZHOO
ventilated.
Safety
- Always disconnect the unit from the mains supply before
connecting/ disconnecting other devices or moving the unit.
- Unplug the unit from the mains socket before a lightning
storm.
- In the interests of safety and to avoid unnecessary energy
consumption, never leave the unit switched on while
unattended for long periods of time, e.g. overnight, while on
holiday or while out of the house.
Switch it off and disconnect the mains plug from the mains
socket.
Mains Adapter Cable
- Make sure the unit or the unit stand is not resting on top of
the mains adapter cable, as the weight of the unit may
 GDPDJHWKHFDEOHDQGFUHDWHDVDIHW\KD]DUG
- Wherethe plug of the Direct Plug-in Adapter coupler is used
as the disconnect device, the disconnect device shall
remain readily operable.
Mains Adapter
- The mains adapter will continue to draw electricity from the
mains supply when plugged in the mains socket. In the
interests of safety and to avoid unnecessary energy
consumption, never leave the adapter plugged in the mains
socket while unattended for long periods of time.
Disconnect the adapter from the power supply.
Interference
- Do not place the unit on or near appliances which may
cause electromagnetic interference. If you do, it may
adversely affect the operating performance of the unit, and
cause a distorted picture or sound.
Batteries
 'RQRWLQJHVWWKHEDWWHU\FKHPLFDO%XUQ+D]DUG
This product contains a coin/button cell battery. If the coin/
button cell battery is swallowed, it can cause severe internal
burns in just 2 hour and can lead to death.
- Keep new and used batteries away from children.
If the battery compartment does not close securely, stop us-
ing the product and keep it away from children.
If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate meeical atten-
tion.
- Batteries used in the remote control for this unit are easily
swallowed by young children and this is dangerous.
- Keep loose batteries away from young children and make
sure that the battery holder tray is secure in the remote
control. Seek medical advice if you believe a cell has been
swallowed.
- Please dispose of batteries correctly by following the
guidance in this manual.
- Batteries (battery pack or batteries installed) shall not be
 H[SRVHGWRH[FHVVLYHKHDWVXFKDVVXQVKLQH¿UHRUWKHOLNH
Supervision
- Children should be supervised to ensure that they do not
play with the unit.
- Never let anyone especially children push anything into the
holes, slots or any other openings in the case - this could
result in a fatal electric shock.
Service
- To reduce the risk of electric shock, do not remove screws.
The unit does not contain any user-serviceable parts.
 3OHDVHOHDYHDOOPDLQWHQDQFHZRUNWRTXDOL¿HGSHUVRQQHO
 'RQRWRSHQDQ\¿[HGFRYHUVDVWKLVPD\H[SRVHGDQJHURXV
voltages.
Maintenance
- Ensure the unit is fully unplugged from the power supply
before cleaning.
- Do not use any type of abrasive pad or abrasive cleaning
solutions as these may damage the unit’s surface.
- Do not use liquids to clean the unit.
FCC
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
$Q\ FKDQJHV RU PRGL¿FDWLRQV QRW H[SUHVVO\ DSSURYHG E\ WKH
party responsible for compliance could void the user’s authority
to operate this equipment.
INDUSTRY CANADA
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference
that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le
présent émetteur radio peut fonctionner avec une antenne
d’un type et d’un gain maximal (ou inférieur) approuvé pour
l’émetteur par Industrie Canada. Dans le but de réduire les
risques de brouillage radioélectrique à l’intention des autres
utilisateurs, il faut choisir le type d’antenne et son gain de
sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.)
ne dépasse pas l’intensité nécessaire à l’établissement d’une
communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Pack Contents
Make sure all of the following contents are included.
- Main Unit
- Main Adaptor
- Audio Cable
- Instruction Manual
Product Overview
1. /
- Skip to previous/next track
- Select a preset radio station
- Adjust time
2.
BF
/SET
- Start or pause
- Set the clock
- Program radio stations
3. VOL+
I
/VOL-
J
- To increase/decrease the volume
4. TUNE
C
/TUNE
D
- Search within a track/USB
- Tune to a radio station
5. ALARM1/ALARM2
- Set the alarm timer
- Turn off the alarm tone
- View alarm settings
- Stop alarm
6. BRIGHTNESS/SNOOZE
- Adjust the display brightness
- Repeat the alarm
7. SLEEP
- Set the sleep timer
8.
/SOURCE
- Turn on the unit or switch to standby mode
- Select a source
9. DISPLAY
- During play, select display information
- For selected FM radio stations, display RDS information
10. ANT
- Attached FM radio antenna
11. AUX IN
- Connect an external device
12.
5V 1A
- Connect the USB mass storage device
- USB Charging Port
13. DC 5V
- Connect the AC adapter
14. Battery compartment
15. Speaker
16. Display panel
- Show current status
Power Operation
Caution: Make all connections before plugging the unit into
the AC Power outlet.
Install battery
Caution: Risk of explosion! Keep battery away from heat,
 VXQVKLQHRU¿UH1HYHUGLVFDUGEDWWHULHVLQ¿UH
)RU¿UVWWLPHXVH
Remove the protective tab to activatethe unit battery.
1. Loosen the screw on the battery compartment cover with a
screwdriver.
2. Replace a new one lithium CR2025 battery with correct
polarity (+/-) as indicated.
3. Close the battery compartment to the original position and
tighten the screw with a screwdriver.
Note: Remove the battery from unit when it is not to be used
for a long period.
Connecting the AC Power
Insert the AC adapter's DC plug into the unit, then insert one
side of AC power cord into a wall outlet, and your system is at
your command!
Caution: Be sure to unplug the power plug from the outlet
when going out or when the unit is not in use for an
extended period of time.
Turning the Power On and Off

Turning the System On
Press the
button, the unit switches to the last selected
source.

Switching the system to Standby mode
Press and hold the
button to switch the unit to standby
mode. The time (if set) appear on the display panel.
Setting the Clock
Setting the Clock Manually
1. In standby mode, press and hold the SET button for 2
seconds, [24 H] begins to blink on the display panel.
2. Set the 12/24 hour format with the
or buttons.
3. Press the SETEXWWRQWRFRQ¿UPDQGWKHKRXUGLJLWVEHJLQWR
blink.
4. Repeat above steps 2-3 to set the hour, minute, month, day,
and year.
Note:
 ,IQREXWWRQLVSUHVVHGLQVHFRQGVWKHXQLWH[LWVFORFN
setting mode automatically.
Automatically synchronize clock with RDS
Tune to a RDS radio station that transmits time signals, the
XQLWFDQ V\QFKURQL]HZLWK WLPHWUDQVPLWWHGE\ 5'6VWDWLRQ
automatically.
General Operation
Adjust volume level
During play, press the VOL+
I
or VOL-
J
buttons to increase/
decrease the volume level.
Adjust display brightness
Press the BRIGHTNESS button repeatedly to select different
levels of display brightness.
Listening to Radio Broadcasts
Caution:
- Position the antenna as far as possible from TV, VCR or
other radiation source.
- For optimal reception, fully extend and adjust the position of
the antenna.

Tuning in to a Station
1. Repeatedly press SOURCE button to select the FM source.
2. Select a station using one of the following methods.
- Auto Tuning
Press and hold the TUNE
C
or TUNE
D
buttons for one
second or more, the frequency changes down or up auto-
matically until a station is found.
- Manual Tuning
Repeatedly press the TUNE
C
or TUNE
D
buttons to
FKDQJHWKHIUHTXHQF\XQWLO\RX¿QGWKHVWDWLRQ\RXZDQW
- Select a preset radio station
Repeatedly press the
or buttons to select the desired
preset number. Its band and frequency are displayed on the
front panel.

Program radio stations manually
You can program a maximum of 20 preset radio stations
(FM).
- Automatically
Press and hold the SET button for two second or more to
activate automatic program mode.
- [AUTO] is displayed.
- All available stations are programmed.
 7KH¿UVWSURJUDPPHGUDGLRVWDWLRQLVEURDGFDVW
automatically.
- Manually
1. Tune to a radio station.
2. Press the SET
button to activate program mode.
- The preset number will blink.
3. Repeatedly press the
or buttons to allocate a number
to this radio station.
Note: If you select more than 20, the preset number will be
changed to “1” automatically.
4. Press the SET
button again to store the station.
5. Repeat above steps 1 to 4 for each station you want to store
in memory with a preset number.
Note: If the system is unplugged or if a power failure occurs,
the preset stations will not be erased.

Show RDS information
Many FM stations are broadcasting added data compatible
with Radio Data System (RDS). This radio set offers conve-
nient functions using such data.
Press the DISPLAY button repeatedly to select the informa-
tion that displayed as follows.
- Programme Service Name
When an RDS station is received, the RDS name of that
station instead of the frequency. When the DISPLAY button
is pressed during Programme Service display, the Clock
Time is displayed for few seconds, then Programme Service
display returns.
- Programme Type
Programme type identification signal. (Example: News,
Rock, Classical music.)
- Radio Text
This displays the news of stations.
- Clock Time System
The Clock Time system may not properly operate in areas
where RDS Clock Time service is not available. Once Clock
Time service is received, the Clock Time system keeps op-
erating. “RDS CLOCK” is displayed in areas where no Clock
Time services are available.
- Changing Display
During Programme Service display, press the DISPLAY but-
ton repeatedly to select the Clock Time, Programme Type or
Frequency. They will be displayed for a few seconds, then
the Programme Service display returns.
Use the USB
Caution: Do not use a high-capacity USB hard disks.
By connecting an USB mass storage device (including USB
ÀDVKPHPRU\86%ÀDVKSOD\HUVRUPHPRU\FDUGVWRWKLVXQLW
you can enjoy the device's stored music through the unit.
1. Insert the USB device's USB plug into the
5V 1A
socket on the rear of the unit.
2. Repeatedly press SOURCE button to select the USB
source.
3. The device's stored music will be played automatically.
- To pause/resume play, press
.
- To skip to a track, press
/ .
- To fast-forward/fast-backward the track, press
C
/
D
- To increase or decrease the volume, press VOL+
I
/
VOL-
J
.
For devices with USB Cables:
1. Insert one plug of the USB cable to the
5V 1A
socket on the rear of the unit.
2. Insert the other plug of the USB cable to the USB output
terminal of the USB device.
For memory Cards:
1. Insert the memory card into a card reader.
2. Use a USB cable to connect the card reader into the
5V 1A socket on the rear of the unit.
Charge for external devices
When the unit is connected to power, the
5V 1A socket
on the rear of the unit to charge of part of the external devices,
such as: phone.
Play from Bluetooth device
The unit has a Bluetooth function that can receive a signal
within 10 metres.
Pairing the unit with a Bluetooth device to listen to music:
1. Repeatedly press SOURCE button to select the bluetooth
source.
2. Activate your Bluetooth device and select the search mode.
3. “MS115BT” will appear on your Bluetooth device.
4. Select “MS115BT” and enter “
0000
” for the password if
necessary.
5. Start music play on your Bluetooth device, you can use this
unit to control the function to your Bluetooth device.
- To pause/resume play, press
.
- To skip to a track, press
/ .
- To increase or decrease the volume, press VOL+
I
/
VOL-
J
.
6. Long pressing the SET button for 5 seconds or more to
disable the function from your Bluetooth device.
Note:
 ,IWKHVLJQDOVWUHQJWKLVZHDN\RXU%OXHWRRWKUHFHLYHUPD\
disconnect, but it will re-enter pairing mode automatically.
 7KLVXQLWVXSSRUWV$'3$GYDQFHG$XGLR'LVWULEXWLRQ
 3UR¿OH
Listening to an external device
You can also listen to an external audio device through this
unit.
1. Repeatedly press SOURCE button to select the AUDIO IN
source.
2. Connect the audio cable to:
- the AUX IN jack (3.5mm) on the back of the unit.
- the headphone jack on an external device.
3. Start to play the device (see the device user manual).
Setting the alarm timer
You can set two alarms which go off at different time.
1. Ensure that you have set the clock correctly. (See "Setting
the Clock".)
2. Press and hold the ALARM1 or ALARM2 buttons for 2
seconds or more, the "
" or " " and the hour digits begin
to blink.
3. Set the hour with the
or buttons.
4. Press the SETEXWWRQWRFRQ¿UPDQG
the minute digits
begin to blink
.
5. Repeat above steps 3-4 to set the minute.
6. Repeat above steps 3-4 to select whether to ring alarm the
whole week, on weekdays, or at weekend.
7. Repeat above steps 3-4 to set the alarm tone (FM, BUZZ or
USB).
8. Repeat above steps 3-4 to set the alarm volume.
Note:
If USB source is selected and the audio cannot be
played, BUZZ is activated automatically.
To deactivate or re-activate an alarm timer
Press the ALARM1 or ALARM2 buttons twice in normal clock
display mode to activate alarm function and again to deactivate
it.
- If timer is activated, "
" or " " is displayed.
- If timer is deactivated, "
" or " " is disappeared.
Repeat alarm
When the alarm rings, press the SNOOZE button, the alarm
repeats ringing 9 minutes later.
Stop alarm ring
When the alarm rings, press the corresponding ALARM1
or ALARM2 buttons, the alarm stops but the alarm settings
remain.
View the alarm settings
Press the corresponding ALARM1 or ALARM2 buttons.
Setting the Sleep Timer
You can set the unit to turn off automatically after a certain
period of time.

When the unit is turned on, press the SLEEP
button
repeatedly to select a set period of time (in minutes):
120, 90, 60, 45, 30, 15
When sleep timer is activated, the “SLEEP” is displayed.
To deactivate sleep timer
Repeatedly press the SLEEP button until "OFF" is displayed.
When sleep timer is deactivated, the “SLEEP” is disappears.
Specifications
Main adaptor
Model No. .............................. Y12FE-050-2000G (for German)
Y12FE-050-2000B (for UK)
Y12FE-050-2000U (for USA)
Vendor .............................................................................Kings
Input............................................$&9+]$
Output..........................................................................5V
2A
Main Unit
FM Frequency Range.........................................a0+]
Output Power.........................................................2W x 2 RMS
USB Port......................................................................5V
1A
Dimensions....................................185(W) x 91(H) x 65(D) mm
Speaker Impedance ............................................................. 4
:
Speaker Input Power............................................................3W
Troubleshooting
If you are having a problem with your unit, check this list for a
possible solution before calling for service.
If you cannot solve the problem from the hints given here, or
WKHXQLW KDVEHHQ SK\VLFDOO\GDPDJHGFDOODTXDOL¿HG SHUVRQ
such as your dealer, for service.
No power
- Ensure that the AC adapter is connected securely.
- Ensure that there is power at the AC Mains.
No sound
- Adjust the volume.
No response from the unit
- Disconnect and reconnect the AC adapter, then turn on the
unit again.
Poor radio reception
- Increase the distance between the unit and your TV or
VCR.
- Fully extend and adjust the FM antenna.
Timer does not work
- Set the clock correctly.
- Switch on the timer.
Clock/timer setting erased
- Power has been interrupted or the power cord has been
disconnected.
- Reset the clock/timer.
The symbol on the product or its packaging indicates that this
product must not be disposed of with your other household
waste. Instead, it is your responsibility to dispose of your waste
equipment by handing it over to a designated collection point
for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment
at the time of disposal will help conserve natural resources
and ensure that it is recycled in a manner that protects human
health and the environment.
For more information about where you can drop off your waste
for recycling, please contact your local authority, or where you
purchased your product.
5
MS115BT
Clock Radio With Bluetooth
INSTRUCTION MANUAL
఺ڎ߿
This device complies with FCC radiation exposure limits set
forth for an uncontrolled environment.
Model:MS115BT