Quick Start Guide

Packing List
Name
Quantity Unit
·
Dual frequency module 1 PCS
·
USB cable 1(length 310 mm) 1 PCS
·
USB cable 2(length 60 mm) 1 PCS
·
Mounting bracket 1 PCS
·
M3.9X30 Screw 2 PCS
·
M3X4 Screw 1 PCS
·
Dual frequency module Quick Start Guide 1 PCS
·
&HUWL¿FDWHRITXDOLW\ 1PCS
·
Warranty card 1 PCS
Safety Guidelines
Observe all safety regulations and precautions
g
Before you start the installation procedure, read all safety precautions described
in this document and observe any warning labels affixed to the equipment. Safety
precautions provided may not cover every eventuality, so remain mindful of safety at
all times.
g
Follow all the safety precautions and instructions provided by ENJOYOR. The safety
precautions outlined in this document are only those that ENJOYOR can predict.
ENJOYOR is not liable for any consequence that results from violation of regulations
pertaining to safe operations or safety codes pertaining to design, production, and
equipment use.
Site Environment
g
Install the RFID Card in an environment free of high temperature, dust, unstable
YROWDJHYLEUDWLRQVWURQJQRLVHDQGQR[LRXVÀDPPDEOHRUH[SORVLYHJDVHVRUVPRNH
as well as free of interference sources such as large radar stations, radio stations, and
electrical substations.
g
Install the RFID Card in a dry environment away from sources of water, and take
SURWHFWLYHPHDVXUHVWRSUHYHQWZDWHUIURPÀRZLQJLQWRWKHHTXLSPHQWDORQJWKHFDEOH
g
Install the RFID Card in a hidden place and ensure that the AP does not disturb daily
work or life of residents.
g
Make the engineering design by fully considering such factors as hydrology, geology,
earthquake, electric power, and traffic. The selected site should comply with the
HQYLURQPHQWGHVLJQVSHFL¿FDWLRQVRIFRPPXQLFDWLRQVHTXLSPHQW
Installing Dual frequency module
1
Attach the mounting bracket against the wall and adjust its position properly. Mark
SRVLWLRQRIWKHPRXQWLQJKROHVZLWKDPDUNHUDVVKRZQLQWKHIROORZLQJ¿JXUH+ROH
spacing: 60mm or 95mm.
Fix the mounting bracket to the wall and use the Phillips screwdriver to fasten two
expansion screws into the expansion tubes.
3
8VHD PPGULOOELWWRGULOO PPPPGHHS KROHVLQ WKHGULOOLQJ SRVLWLRQV
+DPPHUWKHH[SDQVLRQWXEHVLQWRWKHKROHVXQWLOWKHH[SDQVLRQWXEHVDUHFRPSOHWHO\
embedded into the wall.
Align the grooves on the bottom cover of the device with the protection gaps on
the mounting bracket.Slide the device downwards to hang the the device on the
mounting bracket.
If torx security screws are used to prevent theft,use a T9 torx security screwdriver to
tighten the torx security M3x4 screws into the device.With a tightening torque of 0.15
N•m.
2
USB cable connectioning.
4
You need to separately prepare a T9 torx security screwdriver.
Because USB cable 2 is hard wired, it is necessary to remove r251d-e and connect
it with dual frequency module, and then install it on the backplane at the same time.
NOTE
NOTE
Dual frequency module
Quick Start Guide
01 (2020-03-30)
LED States
Wall Mountin
AP7052DN installation method
6SHFL¿FDWLRQ3DUDPHWHU
6L]H+[/[: 32 mm x 86 mm x 150 mm
Power Consumption <2.5 W
Communication Type USB Port
Signal Modulation GFSK
Frequency 0+]
Typical sensitivity -100 dBm
Communication Distance 0 m to 15 m
.+]/RFDWLRQ'LVWDQFH <4 m
Power Port USB Port
UART Port USB Port
LED Number 1 pcs
Operating Temperature -10 °C to +85 °C
2SHUDWLQJ+XPLGLW\ 5 % to 95 %
Storage Temperature Range -40 °C to +70 °C

with package

0571-8993 0384
Name Indicator colo State Describe
System LED
Green Always Powered on
Green 6ORZEOLQN+] Normal work of the system
Red 6ORZEOLQN+] Receiving and sending
Model: E-US400D
www.enjoyor.net
60mm
95mm
90
Ø6
35mm ~ 40mm
1.2N•m
ST3.5
R250D-E installation method R251D-E installation method
USB cable 1
USB cable 2
USB连接线
a
b