User's Manual

ManualsBrandsZHEJIANG YANKON GROUP ManualsElectronicsMotion Sensor

Hardware Installation and Settings

1. Fixing method: the base is attached to the iron or screwed to other materials, then the body is

attracted to the base or placed directly on flat like tables. Please make sure that the body of the

sensor is firmly installed. Otherwise, it may cause false alarms when vibrated or blew with the

fixed object.

2. The distance between the sensor and supporting Bluetooth gateway should not be so far

during installation. It is recommended being within 15 meters without obstruction indoors, or the

distance should be decreased by the material, height, thickness, etc. of obstruction. The

appropriate distance is that the normal sensor alarm can be seen every time on the mobile APP.

3. Detecting direction: When the feet are downwards and the buttons are placed upwards, the

main detecting direction is the human body's left-right movement, while less sensitive to up-

down and far-near movements.

4. Detecting angle : 120 degrees. When the sensor attached to the base can rotate freely at a

certain angle, please turn the lens to a reasonable position to align the main direction of the

human body and avoid the source of interference(For example, a certain distance should the

sensor keep from the space for small animal activities, sun exposure, the sky, lamps, hot water

cups, firelights, cooking utensils, kitchen appliances and all kinds of large heating objects, etc. ,

which can be 1 to 10 meters in different situations).

5. When first installing, please unplug the battery insulator to energize.

6. This sensor is powered by two 1100mAH No. 7 batteries. It can work for about one year if it

tests 60 human body per day on average. After the battery runs out, the user can open the back

cover to replace it by himself following the Instructional drawings provided by the structural

engineer.The spring is connected to the negative electrode of the battery, the entire circuit will

automatically stop working with battery anti-reverse circuit once the battery is reversed.

7. After opening the back cover, the user can set the sensitivity of the sensor by toggling the

small switch on the side of the battery compartment. When it is turned to H (HIGH), the

maximum sensing distance is about 10Meters, suitable for large spaces such as warehouses.

When turned to the L (LOW) , the maximum sensing distance is about 5 meters, which is suitable

for ordinary families. The higher sensitivity, the more likely to be triggered accidentally. The

factory default setting is L, and you can request to specify H when booking in large quantities.

8. When someone is detected, the green indicator light on the sensor will light up and the server

will be reported through the gateway. After the hardware is fixed for a delay of about 1 minute,

the green indicator light will turn on again and report that the person has left via the gateway(It

doesn't matter whether the person is really gone, as long as his movement is not detected, and

the movement must have a certain amplitude).If someone is detected again during this period,

the time will be restarted.

Mobile APP and Software Settings

1. Download and install the “Energetic Lighting” APP from the mobile app store, and register with

your mobile phone number or email address. Please choose the correct region like the United

States or Canada while registering, which will affect the display language and some features while

using , or log in with existing account. The details on home and room management is refer to the

operating instructions of the “Energetic Lighting” APP, then turn on the WIFI and Bluetooth of the

User manual

Summary of content (18 pages)

PAGE 1
User manual Hardware Installation and Settings 1. Fixing method: the base is attached to the iron or screwed to other materials, then the body is attracted to the base or placed directly on flat like tables. Please make sure that the body of the sensor is firmly installed. Otherwise, it may cause false alarms when vibrated or blew with the fixed object. 2. The distance between the sensor and supporting Bluetooth gateway should not be so far during installation.
PAGE 2
mobile phone. 2. Plug the matching Bluetooth gateway into the power supply and configure it. You can refer to the instruction manual of Yankon Smart Lighting for details. 3. Press and hold the small button above the side of the sensor for more than 5s and then release it. You can see the indicator light is flashing inside the lens to initialize the configuration.
PAGE 3
Confirm indicator rapidly blink .
PAGE 4
You can choose to change the name and click “Done” to return to the main interface . If you haven’t seen the newly added device in the main interface, you can pull down to refresh. When there are multiple devices, you can add them one by one as described above, or select Auto Search to add device.You can refer to the instruction manual of Yankon Smart Lighting for details. After tapping the sensor, you can click the record to view the historical time detected .
PAGE 5
1. Add other Yankon smart light that can be linked with, you can refer to the corresponding product manual for details. 2. Some smart devices can be managed by group, You can refer to the instruction manual of Yankon Smart Lighting for details. 3. There are many setting measures for linkage. Here is a simple example that an indicator light will light upwhendetecting someone, and the light will automatically turn offafter 2 minutes. There are countless functions for the user to set.
PAGE 6
Choose the detecting device “PIR” Choose “Human motion detected”
PAGE 7
Then return, click device to select the smart device you want to link, Here select the white ambiance to link
PAGE 8
Choose “Select Function”, then choose “Switch”.
PAGE 9
PAGE 10
Here you can select a time to set the Effective Period,
PAGE 11
Save it after finishing setting. Now the PIR detection linkage lamp: The control to turn on the lampwhen there’s someone has set. Next, set up another automation to turn off the lights: First, similar to the previous one, the condition is how long there’s no person is detected by the same PIR sensor. The choice including 2, 5, 10, 20, 30minutes. We choose 2 minutes.
PAGE 12
PAGE 13
PAGE 14
PAGE 15
Now the PIR detection linkage lamp: The control of turning the lamp off after two minutes or with no person is detected has completed.
PAGE 16
For example: Entering the interface of PIR , you can see that PIR displays information when detecting someone, and specific historical information can also be found in Record. When the PIR detects someone, it will light up the light. The picture below shows that the PIR will linkage control the light off if the PIR haven’t detected people after detected someone 2 minutes ago. When a delay has not expired and someone passed again, it will calculate the delay again based on the last time someone left.
PAGE 17
I. Hardware size, weight and other parameters: Later provided by the structural engineers. 2 Information of package and attachment, etc. …… 3 Maintenance, warranty, exemption, FAQ and other information: It is forbidden to shake the product violently or place it in an area with sharp temperature changes, which may damage the product. When the outside of the product lens is dirty, you can use a soft damp cloth to wipe it. Be careful not to scratch the surface. Do not clean the inside.
PAGE 18
ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence.