Quick Start Guide

ManualsBrandsZhejiang Xunshi Technology ManualsElectronicsProWash S

Table Of Contents

In the Box

Where to Set Up

Level surface away from light and heat.

A C

Congratulations!

Your new ProWash S is the world’s most advanced system

for cleaning 3D printed parts. Featuring improvements to

our patented Mechanical Jetting

technology and an

all-new, cloud-connected onboard computer, your digital

workflow just got a little simpler.

In this guide, you’ll find everything you need to get started

using ProWash S.

Training and Support

ProWash S comes with complimentary

phone and email support. If you have

questions, please get in touch:

Visit

Call

support.sprintray.com

800-914-8004

support@sprintray.com

ProWash S Device

Drain Hose

Pre-installed

(Section 8)

Cleaning

Brush

(Section 9)

Basket

(Section 7)

Hydrometers

Pre-installed

(Section 4)

Power Cable

USB Cable

(Section 12)

Wash Filter

(Sections 2 & 9)

Metal

Tweezers

(Section 10)

Power Adaptor

Magnet Sticker

(Section 6)

Build Platform

Adaptor

(Section 6)

Onboarding

Card

Set up ProWash S in a well-ventilated area on

a level surface in a temperature-controlled

room. Keep it away from windows and bright

light sources.

Never place anything on ProWash S.

If possible, set ProWash S near your 3D

printer and curing device for optimal

workflow efficiency.

ProWash S comes out of the box

with most parts preinstalled.

The hydrometers are precalibrated

for each chamber and will float when

it’s time to replace IPA. Read more

about hydrometers in section 4.

Automated Multistage Cleaning System

Designed for Digital Dentistry

Quick Start Guide

Version 2 - Updated on 06/28/22

Model SRP2208A

QR Code

Hello Akash :)

Summary of content (7 pages)

PAGE 1
Hello Akash :) Automated Multistage Cleaning System Designed for Digital Dentistry Quick Start Guide Version 2 - Updated on 06/28/22 Model SRP2208A Congratulations! Training and Support Your new ProWash S is the world’s most advanced system for cleaning 3D printed parts. Featuring improvements to our patented Mechanical JettingTM technology and an all-new, cloud-connected onboard computer, your digital workflow just got a little simpler. ProWash S comes with complimentary phone and email support.
PAGE 2
3 Plug in and Connect to Network Use the provided power adaptor and cable to plug your ProWash S into a surge protector or uninterrupted power supply. Flip the switch on the back to the ‘On’ position. Touchscreen Drain Hose On startup, ProWash S will prompt you to connect to a network. You can join an existing Wi-Fi network using the touchscreen or use an ethernet cable. Maintaining an internet connection will allow ProWash S to receive updates.
PAGE 3
5 How to Add IPA Always wear gloves and proper eye protection. Open the tank lid and add at least 500mL of IPA 91% or greater to each tank. IPA 99% and ethanol may also be used depending on preference, availability, and material requirements. MAX If the volume of IPA is insufficient to run a cleaning cycle, the onboard computer will detect this and notify you. MIN 500 mL Keep the tank lid closed to prevent the evaporation and contamination of IPA.
PAGE 4
7 How to Wash with ProWash S MAX 4” Print Platform Wash Basket Wash Remove the basket and place the Pro95/S build platform in the wash chamber. If using Pro55/S, use the provided adaptor (see Section 7). Use the touchscreen to select a cleaning cycle. To use the basket, place models inside and close the lid. Use the touchscreen to select a cleaning cycle. The system will not start until a platform is detected.
PAGE 5
Draining an IPA Tank MAX Retrieve the drain hose from the back of the device, then press the metal tip into the drainage port until it clicks into place Point the end of the hose into a disposal container, then unlock the safety clamp to start the flow Once the tank is empty, eject the drain hose by sliding the outer ring of the drain port away from you How to Dispose of IPA ProWash S extracts the maximum life out of IPA so that you generate less waste.
PAGE 6
10 How to Clean the Wash Filter ProWash S has a mesh filter that protects the plumbing from resin and other debris. The filter should be cleaned when prompted by the onboard software. If the filter is damaged or cannot be cleaned, it should be replaced. Start by Locating the Filter In the wash chamber near the propeller WARNING! The secondary mesh below the removable filter should never be removed Remove Clear the area around the filter to ensure no debris falls into the plumbing when it is removed.
PAGE 7
FCC Warning: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules.