Network PTZ Cameras Quick Guide V1.
Waterproof Requirements Please waterproof cables in accordance with the following instructions. User shall assume all responsibility for device damage caused by water due to improper waterproof measures. NOTE! ⚫ Before you start, connect all the needed cables and cut off the copper wires for the cables that you don't use. ⚫ Please use self-adhesive waterproof tape (supplied with some products) to protect the cables. ⚫ Use waterproof components to protect the network cable.
. Install the supplied waterproof components to the network cable in sequence. CAUTION! You need to mount the rubber ring onto the network cable interface first. 4. If your camera has a DC cable and you will not use it, insert the plug into the interface. DC interface Plug 5. (Optional) After the waterproof treatment is completed, put the cables into a waterproof junction box (purchased separately). CAUTION! ⚫ The cable connector must not be exposed and must be kept away from water.
1 Packing List Contact your local dealer if the package is damaged or incomplete. The components may vary with device model. No. Name Qty Unit 1 Camera 1 PCS 2 Waterproof components 1 Set 3 Drill template 1 PCS 4 Screw components 1 Set 5 User manual 1 Set 2 Safety Informations Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the safety instructions before installation and operation. 2.
film from the cover until mounting is finished. Remove the protective film before powering on the device. ⚫ Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance. 2.2 Maintenance ⚫ If there is grease or a dust stain on the front glass surface, clean the glass surface gently from the center outward using anti-static gloves or an oil-free cloth.
3.2 Cable Connection Tail cables may vary with device model. The following figure shows an example. Power cable Network cable IP Network 4 Installation 4.1 (Optional) Install SD Card You need to install a Micro SD card first if you want to save video on an on-board SD card. NOTE! ⚫ You need to format the Micro SD card before use. The Micro SD card can be formatted on the camera's Web interface. ⚫ For recommended SD card specifications, please contact your dealer or technical support.
WARNING! ⚫ Before you insert or remove the Micro SD card, be sure to disconnect power and wait till the camera stops operation; otherwise, the camera or the Micro SD card may be damaged. ⚫ Do not disassemble the device in high humidity environment. The high humidity inside the device will cause lens fogging. 4.2 Wall Mount 1. Locate the positions of holes by pasting the drill template. CAUTION! Keep the line formed by the two holes on the template bottom horizontal. Drill template 2.
Plastic anchors 4. Insert the self-tapping screws through the guide holes on the camera base, and use a screwdriver to fasten it onto the wall. Plastic anchors Self-tapping screws 5 Startup After you have installed the device, connect one end of the power adapter (which needs to be purchased separately) to power supply, and the other end to the power interface to start up the device. 6 Web Login Log in to the Web interface to manage and maintain the device.
1. Open your browser, input the camera’s IP address 192.168.1.13 in the address bar and then press Enter to open the login page. 2. Enter the username and password (admin/123456 by default) and then click Login. NOTE! ⚫ DHCP is enabled by default. If a DHCP server is deployed in the network, the IP address of your camera may be assigned dynamically, and you need to use the assigned IP address to log in. ⚫ If prompted, install the plug-in at your first login.
Disclaimer and Safety Warnings Copyright Statement No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from our company (referred to as us hereafter). The product described in this manual may contain proprietary software owned by our company and its possible licensors.
and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for a particular purpose, and noninfringement. ⚫ Users must assume total responsibility and all risks for connecting the product to the Internet, including, but not limited to, network attack, hacking, and virus.
⚫ Choose username and password discretely: Avoid using the username and password of your social media, bank, email account, etc, as the username and password of your device, in case your social media, bank and email account information is leaked. ⚫ Restrict user permissions: If more than one user needs access to your system, make sure each user is granted only the necessary permissions.
⚫ Use a UL certified power supply that meets LPS requirements if an adapter is used. ⚫ Use the recommended cordset (power cord) in accordance with the specified ratings. ⚫ Only use the power adapter supplied with your device. ⚫ Use a mains socket outlet with a protective earthing (grounding) connection. ⚫ Ground your device properly if the device is intended to be grounded.
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
