IP Camera Quick Guide Ｃ１Ｌ－ ２ＷＮ V1.
1 Packing List Contact your local dealer if the package is damaged or incomplete. The attachment s may vary with models, please see the actual model for details . No. Name Qty Unit 1 Camera 1 PCS 2 Power adapter 1 PCS 3* Screw components （1） 1 Set 4* Mount accessory （2） 1 Set 5 User manual 1 Set Remarks: * means optional and supplied with certain models only. (1)Including one or more accessories such as screws and hex key.
Appearance The following figure shows device dimensions. The appearance may vary with device model. Φ83.1mm Φ(3.3") 77.0mm (3.0") 77.0mm (3.0") 42.4mm (1.
Network interface RESET button Power interface NOTE! Use the reset button to restore factory defaults. When the camera is operating, press and hold the reset button for at least 10 seconds, and wait for the camera to restart. Factory default settings are restored when the camera is restarted.
NOTE! Use the adjustable bracket to adjust monitoring direction. 4 Mount Your Camera 4.1 (Optional) Insert the Micro SD Card You need to install a Micro SD card first if you want to save video on an on -board SD card. Insert the Micro SD card into the side card slot. Before you insert or remov e the Micro SD card, be sure to disconnect power and wait till the camera stops operation; otherwise, the camera or the Micro SD card may be damaged. Micro SD card slot 4.
2. Insert the plastic expansion bolts, knock them into the wall with a rubber hammer, and make sure that they are tightened up. 3. Screw the iron plate to the wall. 4. Attach the camera to the plate. 5 Startup After you have installed the device, connect one end of the power adapter to power supply, and then connect the other end to the power interface to start up the device.
6 Access Your Camera 1. Open your Web browser, enter the camera's IP address in the address bar, and then press Enter. The default IP is 192.168.1.13. 2. In the login page, enter the default username and password ( admin/123456), then click Login. NOTE! DHCP is enabled by default. If a DHCP server is used in your network, your camera may be assigned an IP address, and you need to use the assigned IP address to log in. You may need to install a plug-in at your first login.
Disclaimer and Safety Warnings Copyright Statement ©2020 Zhejiang Uniview Technologies Co., Ltd. All rights reserved. No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from Zhejiang Uniview Technolo gies Co., Ltd (referred to as Uniview or us hereafter). The product described in this manual may contain proprietary software owned by Uniview and its possible licensors.
Uniview reserves the right to change any information in this manual without any prior notice or indication. Due to such reasons as product version upgrade or regulatory requirement of relevant regions, this manual will be periodically updated. Disclaimer of Liability To the extent allowed by applicable law, in no event will Uniview be liable for any special, incidental, indirect, consequential damages, nor for any loss of profits, data, and documents.
Enable HTTPS/SSL: Use SSL certificate to encrypt HTTP communications and ensure data security. Enable IP address filtering: Allow access only from the specified IP addresses. Minimum port mapping: Configure your router or firewall to open a minimum set of ports to the WAN and keep only the necessary port mappings. Never set the device as the DMZ host or configure a full cone NAT.
Make sure the power supply provides a stable voltage that meets the power requirements of the device. Make sure the power supply's output power exceeds the total maximum power of all the connected devices. Verify that the device is properly installed before connecting it to power. Do not remove the seal from the device body without consulting Uniview first. Do not attempt to service the product yourself. Contact a trained professional for maintenance.
Chemical Burn Hazard. This product contains a coin cell battery. Do not ingest battery. If the coin cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
LVD/EMC Directive This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU, 2014/53/EU. WEEE Directive–2012/19/EU The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner. Battery Directive-2013/56/EC Battery in the product complies with the European Battery Directive 2013/56/EC.
