Video Doorbell 1
1 Doorbell Appearance ·Front and Rear Panels Microphone Indicator Light Power Supply Terminal Power Supply Terminal Doorbell Button Indicator, button and microphone Power supply terminal ·Side Panel Anti-theft Screw Hole Speaker Speaker Anti-theft screw hole 1
·Inside Micro SD Card slot Reset Button Micro SD card slot Reset button 1 2
2 In The Box Doorbell body Replaceable faceplate Angle adjustment bracket (horizontal) Flat bracket Angle adjustment bracket (vertical) Mounting level 3
Dual purpose screwdriver Anti-theft screw*2 Set screw for power wire*3 Set screw for securing the body to bracket*3 Self-tapping screw (0.75”)*3 Self-tapping screw (1.
3 Doorbell Installation Install Micro SD Card 1. Open the faceplate from 2. Open the Micro SD the bottom. card slot cover. 3. Insert the Micro SD card.
Install the Doorbell 1. Install the mounting level, and mark points on the wall for drilling according to the mounting level. 2. Drill holes on the wall, insert expansion bolts, and then insert 0.75” self-tapping screws.
3. Connect the power wires coming out of the wall to the terminals on the back of the doorbell with set screws.(DC 12V or AC 16~24V ) 4. Open the faceplate from the bottom.
5. Secure the doorbell body to the bracket using the corresponding set screws. 6. Attach the faceplate to the body from the top.
7. Tighten the anti-theft screws at the bottom of the device using the screwdriver.
Install the Bracket(Three ways) A. Install the angle adjustment bracket with 0.75” self-tapping screws. B. Install the angle adjustment bracket with 0.75” self-tapping screws.
C. Stack angle adjustment brackets (1)Stack the vertical angle adjustment bracket on top of the horizontal angle adjustment bracket, then install the brackets onto the wall. ( 2 ) Use the supplied 1.26” self-tapping screws when stacking brackets.
4 Set Up Download EZLive Make sure your mobile phone has been connected to WiFi. Scan the following QR code to download and install EZLive. https://a.app.qq.com/o/simple.jsp?pkgname=com.uniview.ap p.smb.phone.en.lingyun Add Devices 1. Open EZLive, sign up an overseas account and log in.
2. Click in the upper right corner, and select “Add Wi-Fi Device”. 13 3. Choose video doorbell device.
4. Follow the instructions to prepare the device ready for configuration.
5. Complete configuration information and Scan the QR code on the doorbell.
6. A QR code will be 7. Use the camera of the Generated on the APP. doorbell to scan the QR code. When the doorbell indicator turns into steady green and you hear Connected”, “Network click Success. Continue.
8. Set DST after the device is added.
9. View the doorbell in the device list.
Doorbell Indicator Status During Setup Indicator Status Description Steady red The device is starting up Steady green Wi-Fi connection succeed Blinking green 1. Waiting for Wi-Fi configuration. 2. QR code scanned, connecting Wi-Fi. Doorbell Indicator Status After Setup Indicator Status Description Steady green 1. Normal 2.
Doorbell Indicator Status During Exception Indicator Status Description Blinking red 1. Wi-Fi connection failed. 2. The doorbell resetting is or restarting. Steady yellow The doorbell gets offline after connected to Wi-Fi.
5 Doorbell Operation Two-way Audio 21
Live View 22
Playback 23
6 Notes 1. Make sure the connected Wi-Fi is 2.4GHz. 2. Make sure your router is close to the doorbell. 3. The installation height of the doorbell is about 1.6 meters. 4. Do not install the doorbell on the metal door to avoid signal interference.
Regulatory Compliance FCC Part 15 Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU. WEEE Directive–2012/19/EU The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner.
Battery in the product complies with the European Battery Directive 2013/56/EC. For proper recycling, return the battery to your supplier or to a designated collection point.
Zhejiang Uniview Technologies Co., Ltd. Building No.10, Wanlun Science Park, Jiangling Road 88, Binjiang District, Hangzhou, Zhejiang, China (310051) Email: overseasbusiness@uniview.com; globalsupport@uniview.com http://www.uniview.com ©2019 Zhejiang Uniview Technologies Co., Ltd. All rights reserved. *Product specifications and availability are subject to change without notice.
Version: V1.