Network Bullet Cameras Quick Guide V1.
Safety and Compliance Information Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the Safety Instructions supplied with your equipment before installation and operation. Installation This device is a class A product and may cause radio interference. Take measures if necessary. Make sure the camera operates in an environment where the temperature and humidity meet requirements.
scratch and contamination, etc. In order to keep the cover clean, do not remove the protective film on the cover during mounting. After mounting is finished, remove the film before the device is powered on. Contact professionals for maintenance information. Do not attempt to dismantle the device by yourself. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
Regulatory Compliance FCC statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. LVD/EMC/RE Directive This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU and 2014/53/EU.
Default IP, Username and Password Default IP address: 192.168.1.13 Default username: admin Default password: 123456 The default password is used for your first login. To ensure account security, please change the password after your first login. You are recommended to set a strong password (no less than eight characters). Packing List Contact your local dealer if the package is damaged or incomplete. The attachments may vary with models, please see the actual model for details.
Appearance Dimensions 62.42mm 90.10mm 162.45mm 31.00mm 8.90mm 6 62.67mm 39.00mm 39.
Cable Connection Power interface Network interface IP Network For specifications, see the latest product datasheets. Press and hold the RESET button for at least 15 seconds to restore factory default settings. Perform this operation within 10 minutes after the device is powered on or the reset will fail otherwise. Mount Your Camera (Optional) Insert the Micro SD Card For cameras that support Micro SD, you need to insert the Micro SD card after opening the bottom cover of camera.
For recommended SD card specifications, contact your dealer. 1. Loosen recessed the cross- screws 2. Insert the Micro SD to card. open the bottom cover. Micro SD slot Wall Mount You can adopt wall mount or ceiling mount and purchase hardware accessories by yourself. The following part takes wall mount as an example. Ceiling mount is similar to wall mount and therefore is omitted here. 1. Locate the positions of the holes. 8 2. Drill holes on the wall.
1 Paste installation positioning 1 Use a Ø6-6.5mm drill bit. stickers on the wall and align the cross center to the hole in the wall. 2 Drill 30 mm-depth guide 2 Lead the cables across the hole on the wall. 3. Mount the plastic rivets of self-tapping screws. holes according to the positions marked by stickers. 4. Screw the locknut to loosen the universal joint before attaching your camera to the wall. Knock the plastic rivets into the guide holes and ensure that they are tightened up. Locknut 5.
Antenna Interface Antenna Reset Lead tapping screws through the guide holes in the base and fix them on the wall by using a screwdriver. 7. Adjust the monitoring direction. 1 8. Power on your camera and adjust images. 3 2 1 Adjust the opening of the universal joints as required. 2 Rotate the spherical hinge of the camera to get the desired monitoring direction. 3 Tighten the locknut.
installation is adopted, cables are not penetrated into the wall but threaded out from the outlet on one side of the base. Access Your Camera Before you begin, check that: Your camera is operating properly and connected to the network. The PC you are using is installed with Internet Explorer 7.0 or later. Follow these steps to access your camera through the Web: Open your browser, input the IP address of your camera in the address bar and then press Enter to open the login page.
If the installation failed, open Internet Option in IE before login. Click the Security tab, click Trusted sites, and then click Sites to add the website. If you use Windows 7, you need to save the setup.exe to your PC first, and then right-click the file, select Run as administrator, and then install it according to instructions.
