User Manual A01-A60 LED Lamp LED + Wi-Fi REPEATER Features Install like any other light bulb. Easy to setup and enjoy the extended Wi-Fi signal coverage evenly. Supports two Wi-Fi network mode: Access Point (AP) / Repeater Two build-in antennas for high throughput data exchange rate of maximum 300Mbps Compatible with most smart phones, tablets and computers that support Wi-Fi IEEE 802.11b/g/n standard at 2.4GHz.
Operating Humidity: 10% ≤ RH ≤ 95%, Non condensation Atmospheric Pressure: 86kPa ~ 106kPa Colour: Neutral White Dimensions: 120mm (H) x Φ 60mm (Dia.) Weight: 290g (approx.) Spécifications de produit (par ampoule) • Alimentation: 100 ~ 230V AC, 50/60 Hz • Douille: E26 / E27 / B22 • Consommation d’énergie: 7.
Power: 1.8 Watts (Standby), 2.8 Watts (Full load) 2T2R MIMO wireless technology Security Mode: 64/128 bit WPA-PSK/WPA2-PSK, WPA/WPA2 Encryption Type: WEP64/WEP128/TKIP/AES Wi-Fi Transmitter power: @ 802.11b: +15dBm (Max) @ 802.11g: +15dBm (Max) @ 802.11n: +17dBm (Max) Wi-Fi Receiver power: @ 802.11b: -89dBm @ 802.11g: -81dBm @ 802.11n: -71dBm Distance Range between Router and A01-A60 Bulb: 115 feet (near line of sight) © 2014 SENGLED, Incorporated. All rights reserved.
5. Launch the boost by Sengled application, and a 'Welcome' page appears. At the beginning, press the "network" tab to initialize boost A01-A60 bulb's configuration. After that, click the “START” button to enter the configuration and control interface of the bulb/s. 6. The App will search and list out nearby available wireless router/s automatically. Choose one of the routers as the root router. Type in the Access Password and press “Next” to move forward.
7. Input the access password which is as the router Wi-Fi router, click “Next” to enter the Next step. At this point, APP will send multicast to make the lamp of the Factory Settings is connected to the root router, and the program will search out these lamps. The names of these lamps apply their MAC address the name of the last two as a suffix, and display them on the interface for users to choose whether to access the network.
bulbs, the interface shows a Main Control Page. This can be used to control the overall LED light dimming and ON/OFF. 11. To control the LED bulb individually, pull up the bulb list at the bottom, each bulb can be dimmed separately. Click the arrow on the right, and it goes to the bulb wireless network configuration page. Main page shows that adjust total brightness. The list displays the brightness of each lamp.
following figure. If need editing the lamp information, click the edit button at top right corner, and enter the lamp password to edit mode. Enter the edit mode, basic setup can modify the SSID, the Name of the light, and set the brightness which the lamp is in power memory last time, so as to recover after the next to electricity save. Security Settings change the lamp encrypted and password.
13. If re-configuration of the wireless network is needed, press the Setting Menu button on the Main Control Page and click the "Network" tab. Re-initialize all bulbs on the network and start setup wizard again. 14. If the bulb cannot be detected by the portable smart devices or App in any ways, user can press the physical RESET button to reset the configuration of the bulb (in the middle of the LED lens), as shown below.
RESET button IMPORTANT SAFETY INSTRUCTIONS • Read and keep these safety instructions. • Heed all warnings contained within these instructions. • Please follow all user manual instructions when installing the product. • Clean SENGLED product only with a dry towel. • This Product is intended for indoor use only. • Do NOT use this product outdoors. • Do NOT get this product wet and do NOT use near any water source. • The product should not be exposed to dripping or splashing liquids of any kind.
apart. There are no serviceable parts inside. • To prevent product failure, the bulb should only be installed in operating environments. • Do not block any ventilation openings on the product. • Never push any objects into the openings or slots on the product. Doing so may create an electric shock or fire hazard. • Maintain sufficient distance around your product for sufficient ventilation, do not put anything within at least 6 inches of lightbulb socket.
Warranty Information Warranty statement For this product, the manufacturer grants a warranty of 2 years for workmanship and material. Warranty repairs may be performed exclusively by an authorised customer service. The original sales receipt has to be enclosed as proof.
FCC STATEMENT FOR USERS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. SECTION 15.
co-located or operated in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance.
IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste,ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.