User's Manual

ManualsBrandsZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY ManualsElectronicsRF Remote Control

JCHR35H6D1 Remote control User manual

1、Remote control Effect Picture

2、Remote control function description

2.1、 Pairing:

Remote control pair code:

1) put the battery into the remote control.

2) power the control box (supporting our control box).

3) at the same time, hold down the head up button on the remote control

and the foot up button. When the LED on the control box to be matched stops

flashing and the buzzer makes a sound, the pairing operation is completed. To

test whether or not the pairing is successful, head up/down, foot up and down

keys, buttons and so on related to drive, if you can hear the "tick" sound emitted

by the relay, specification matching success. Otherwise, repeat all the above

steps.

Note: after successful code alignment, operate any two buttons at the same time during

use, and the remote control will not send signals.

Summary of content (6 pages)

PAGE 1
JCHR35H6D1 Remote control User manual 1、Remote control Effect Picture 2、Remote control function description 2.1、 Pairing: Remote control pair code: 1) put the battery into the remote control. 2) power the control box (supporting our control box). 3) at the same time, hold down the head up button on the remote control and the foot up button. When the LED on the control box to be matched stops flashing and the buzzer makes a sound, the pairing operation is completed.
PAGE 2
3、Function description Learning function: after the controller is powered on or long press the learning button, it enters the learning state. The green light of the controller keeps flashing. In the learning state, press the "head up" and "foot up" buttons of the remote control at the same time until the controller will emit a "tick". At the same time, the blue headlight of the remote control flashes twice to indicate that the learning is completed, and the green light of the controller stops flashing. 3.
PAGE 3
Under-bed lighting, massage), actuator will stop moving and begin to perform the button’s function. FLAT Buttons: Press FLAT, actuator begin to lower, until the actuators arrive in the lowest position. During this process, press any button (such as under-bed lighting, massage., etc.) the actuator will stop moving, and begin to perform the button’s function. ZG/ANTI SONRE Buttons： Press ZG or ANTI-SNORE button, actuator will move to corresponding position.
PAGE 4
reaches the third gear, the massage will turn off. It means, the massage operates with the round cycle 0-1-2-3-0. Stop Button: Press the button to turn off the massage. There only have one massage mode—Continues mode. Currently users can switch the massage mode in Dream Motion APP, but cannot switch in wireless remote. (This item will be supplemented if have changes) 3.2 Dial switch: the dial switch has three gears in total: left (gear A) - middle (gear AB) - right (gear B).
PAGE 5
M1 push rod up 0X01 M1 push rod down 0X04 M2 push rod up 0X02 M2 push rod down 0X05 FLAT location 0X08 ZG location 0x07 Memory location A 0x0A Memory location B 0x0C Antisnore location 0x09 Night light 0x13 foot massage 0x0F head massage 0x0D Massage stop 0x0E 5、Others 5.1. The operating frequency range： 2404MHZ~2479MHZ; 5.2. Maximum RF output power of the product: The overall power of the remote control is 82.72 dBμV/m. 5.3.
PAGE 6
、Remark A、FCC 15.21 Information to user Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. B、FCC 15.19 Information to user This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.