Network Keyboard 5000 Series Quick Start Guide V2.0.
Foreword General This document mainly introduces appearance, functions and operations of network keyboard (hereinafter referred to be "the keyboard"). Models NKB5000, NKB5000-F Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a high potential hazard which, if not avoided, will result in DANGER death or serious injury.
Revision History Version Revision Content Release Time October 2019 Add audio adjustment, task management, plan tour and channel group configuration to local preview module. DSS-PRO, DSS-C9100 and DSS-Express platforms support TV wall and live view. Add safety baseline V1.4 needs. Lock the screen with one button. V1.1.0 Update the program December 2018 V1.0.0 First Release October 2017 V2.0.
Important Safeguards and Warnings The following description is the correct application method of the device. Please read the manual carefully before use, in order to prevent danger and property loss. Strictly conform to the manual during application and keep it properly after reading. Operating Requirement Do not place and install the device in an area exposed to direct sunlight or near heat generating device. Do not install the device in a humid, dusty or fuliginous area.
Table of Contents Foreword .................................................................................................................................................... I Important Safeguards and Warnings .................................................................................................... III 1 Introduction............................................................................................................................................ 1 1.1 Overview .........................
4.3.5 TV Wall Icon Description .................................................................................................. 39 4.3.6 PTZ Control ...................................................................................................................... 40 4.3.7 Adding Tasks ..................................................................................................................... 40 4.3.8 Configuring TV Wall .........................................................................
1 Introduction 1.1 Overview The network keyboard can add TV wall, display videos on the TV wall, and carry out PTZ control. For appearance of network keyboard, see Figure 1-1. For details, see Table 1-1. Figure 1-1 Appearance Table 1-1 Icon description No. Icon Function Working power indicator light. Power Green light turns on when working power of network keyboard is normal. 1 Network indicator light. Network Green light turns on when the keyboard is connected to network normally.
No. Icon Function Navigation bar. Homepage. 4 Return. 5 Fn Function key. It is line scanning by default. Preset Make PTZ control, and configure preset point. Tour Make PTZ control, and tour between points. Aux Auxiliary key. It is pattern by default. Includes remote control lever, auxiliary menu and — 6 function operation. 1.2 Key Module Key module is not available in platform preview mode. F1 cannot be called in platform TV wall mode.
Key Example Function Operation mode switch. Mode It is operation mode at Reserved. present. 0–9 Number 0–9 — Screen 123 + Screen Select screen. Window 3 + Window Focus on the third window of present screen. Split 4 + Split Divide present screen into 4 splits. Press Delete 1 digit from number buffer zone. The icon is similar to squares. Drag No. 123 camera group onto the current (Camera group) 123 + window for automatic tour of videos in the channel. Drag No.
Figure 1-3 Rear panel port Table 1-3 Rear panel port description Number Name Description 1 Wi-Fi port Connect Wi-Fi antenna. 2 Grounding stud Grounding. 3 USB2.0 Connect mouse and USB. 4 RS–232 Connect serial port. 5 Alarm input/output port For details, see Table 1-4. 6 Network port Connect the network. 7 USB3.0 Connect mouse and USB. 8 Microphone Connect microphone. 9 Earphone Connect earphone. 10 HDMI1–HDMI4 11 Power port Connect power cord to supply power.
Name Description RS-232 receiving and sending port. Rx, Tx Reserved. The software does not support at present. 3 groups of alarm output port. NO1C1, NO2C2, NO3C3 Reserved. The software does not support at present. RS-422 port. R+, R-, T+, TReserved. The software does not support at present. 1.3.2 Side Panel Port There are three keys on the side panel, including mute key, volume up key and volume down key.
2 Start and Shutdown 2.1 Start Connect the power, press power button, and boot up the network keyboard. The system displays login interface after it is booted up successfully. Its interface can be operated with touch screen and external mouse. 2.2 Shutdown Step 1 Shutdown. Method 1: Click at the upper right corner of main interface, and then select Shutdown to exit the system. Method 2: Press power button on the rear panel.
3 Quick Configuration 3.1 Initialization Initialize the device for the first use. On the login interface, press and hold at the lower left corner of the keyboard for 15 s. The interface prompts that "Do you want to clear all of the configurations?" Click OK to initialize the device. All configurations will be cleared after initialization. Be cautious. Step 1 Boot up the device. The End-User License Agreement interface is displayed.
Figure 3-1 Main interface Table 3-1 Main interface description Name Preview Description Decode and preview local encoding devices and corresponding operations. TV wall Control the locally added decoder, matrix and TV wall. Playback Play back videos in local added recording device. Platform Settings After connecting to the platform, network keyboard is able to control devices on the platform. There are four modules, including device, general, account and system.
Figure 3-2 Settings Table 3-2 Settings description Name Device Description Add, modify and delete devices; view input channel, and modify input channel number. General Set network, Bluetooth, serial port, date, time, hardware and MAC. Account Add, delete and modify role information and account information. System View program version and upgrade. Click at the upper right corner, and a navigation bar appears in the page.
Figure 3-3 Network Step 2 Set the parameters. For details, see Table 3-3. Table 3-3 Wired network parameter description Parameter Description It includes multi-address, fault tolerance and load balance. Multi-address: Two Ethernet cards are used independently. During network status detection, network is deemed to be disconnected if one Ethernet card is disconnected. Fault tolerance: Two Ethernet cards use one IP address.
Parameter Description IP version Keep the default value. Ethernet card Select Ethernet card. IP address Subnet mask Gateway Enter numbers to modify IP address, set corresponding Subnet Mask and Gateway. Default IP address of network keyboard is 192.168.1.108. Preferred DNS IP address of DNS server. Alternate DNS IP address of alternate DNS server. Step 3 Click Save. 3.5.2 Wi-Fi On the General interface, click the Wi-Fi tab to enter the interface.
Figure 3-5 Wi-Fi connection Step 2 Enter correct password, and then tap . In case of successful connection, the connected Wi-Fi Name and Connected will be displayed at the upper-left corner. Disconnect Wi-Fi Click on the right of connected Wi-Fi and click Disconnect in the pop-up dialog box. See Figure 3-6. Click to disconnect the Wi-Fi. Figure 3-6 Disconnect 3.6 Adding Device It includes manual adding and auto search. On the Settings interface, click Device. The Device interface is displayed.
Figure 3-7 Device 3.6.2 Manual Add Step 1 On the Device interface, click . The Manual Add dialog box is displayed. Step 2 Select Protocol. The Protocol interface is displayed. See Figure 3-8.
Figure 3-9 Manual add (ONVIF) Step 3 Set the parameters. See Table 3-4. Table 3-4 Manual add parameter description Parameter Description Select protocol type. It supports Private and Onvif at present. Protocol With ONVIF protocol, PTZ control only supports rotation and zoom function in the fixed speed mode, rather than other auxiliary PTZ functions. Start IP and End IP Enter start IP and end IP when one IP segment is added. Enter start IP when one IP is added. Port Enter port number.
Click . The Dev Import interface is displayed. See Figure 3-10. Click USB Check to check USB capacity. Click Dev Import to import device files. Figure 3-10 Dev Import Click . The Dev Export interface is displayed. Click USB Check to check whether USB flash drive is inserted, and then click Dev Export to export files. Select Dev Export Encryption to export encrypted files. See Figure 3-11. If Dev Export Encryption is not selected, export unencrypted files. See Figure 3-12.
Figure 3-12 Dev Export (Unencrypted) Click to refresh the interface. 3.6.3 Auto Search Step 1 On the Device interface, click . The auto search interface is displayed. See Figure 3-13. Figure 3-13 Auto search setting Step 2 Enter IP segment and select the check box. Step 3 Click Save.
The auto search results are displayed. See Figure 3-14. Alternatively, click to view search results. Figure 3-14 Auto search result Step 4 Select the check box in the line of a device, and then click to add the device.
4 System Configurations 4.1 Preview Preview local devices, video on wall, PTZ control, snapshot and recording. There are 3 buttons on the side panel, including mute button, volume up button and volume down button, to adjust the volume of local preview interface. Click Preview on the main interface. The Preview interface is displayed. See Figure 4-1. There are five modes, including HDMI1–HDMI4 and VGA5. Figure 4-1 Preview 4.1.
Icon Description Icon Maximize and restore Description Single split. the window. 4-split. 9-split. Custom split. 16-split. Local preview interface does not support custom split. Select window/all windows on the screen. PTZ. This button is used with deletion button. Smart stream mode. Switch main and sub streams on the local preview Delete. interface. Manual switch is not needed on the local preview interface. 4.1.2 Channel Grouping Step 1 On the Preview interface, click .
Figure 4-2 Input channel (1) Step 2 Click . The Add channel interface is displayed. See Figure 4-3. Figure 4-3 Add channel Step 3 Select the channels, and then click OK. The added channels are displayed on the Input Channel interface. Step 4 Click Group. The Channel grouping interface is displayed. See Figure 4-4.
Figure 4-4 Channel grouping Step 5 Select Input group, and then configure Group name and Time. Step 6 Select the channels that you need. Click on the Channel grouping interface to add channels. Step 7 Click Save to save the channel group. 4.1.3 Video on Wall Step 1 On the Preview interface, select HDMI1–HDMI4 or VGA5 in drop-down list. Step 2 Select video source on the right, drag it onto TV wall or double-click the video source. Quick Video on Wall (Optional) Click , and a dialog box pops up.
Figure 4-5 Short-cut Refer to "4.6.1.2 Input Channel" to inquire Number in the input channel. Relevant operation Click , and channel with the previous number will be displayed on wall. For example, current number is 123, click Click , and No. 122 channel will be displayed on the wall. , and channel with the next number will be displayed on wall. For example, current number is 123, click Channel group does not support , and No. 124 channel will be displayed on the wall. and at present.
Figure 4-6 Keypad Maximize and Restore Window Click to maximize and restore the window. Single, 4, 9, 16 and Custom Split Click , , , or respectively, representing single, 4, 9, 16 or custom split. Clearing Video Source Step 1 Select a window. Click to select the focused window. Click again and the icon turns into to select all windows within present operating screen. Step 2 Click . Smart Stream Mode Main stream goes on wall in case of single split.
4.1.5.1 Adding Task Step 1 On the Preview interface, select video according to actual needs. For example, play the videos of channel 1 and channel 2. Step 2 Click on the Preview interface. The Add Task interface is displayed. See Figure 4-7. Figure 4-7 Add Task Step 3 Enter task name. Step 4 Click to save the task. 4.1.5.2 Viewing Task Select task name from Add Task drop-down list. See Figure 4-8. You can view the task.
4.1.5.3 Deleting the Scheme Step 1 Click . The Scheme Config interface is displayed. See Figure 4-9. Figure 4-9 Scheme Config Step 2 Select the scheme that you want to delete, and then click to delete it. 4.1.6 Patrol Config Carry out patrol according to the sequence of adding scheme to the patrol. Step 1 On the Scheme Config interface, click Patrol Config. The Patrol Config interface is displayed. See Figure 4-10.
Figure 4-10 Patrol Config Step 2 Click . The Scheme Config interface is displayed. See Figure 4-11. Figure 4-11 Scheme Config Step 3 Select the scheme, and click OK. Scheme can only be added one by one. If less than 2 schemes are added, patrol is not available. Step 4 Click Return to configure Patrol Time. Relevant Operation On the Preview interface, click to enable patrol. See Figure 4-12.
Figure 4-12 Patrol Click to stop the patrol. See Figure 4-13. Figure 4-13 Stop patrol 4.1.7 Snapshot Step 1 Insert the USB flash drive into network keyboard. Step 2 On the Preview interface, click . The Snap & Record interface is displayed. Step 3 Set the snapshot storage path. For details, refer to "4.1.9 Snapshot and Recording Settings." Step 4 On the Preview interface, click . You can take a snapshot with joystick buttons.
4.1.8 Recording Step 1 Insert the USB flash drive into network keyboard. Step 2 On the Preview interface, click . The Snap & Record interface is displayed. Step 3 Set the recording storage path. For details, refer to "4.1.9 Snapshot and Recording Settings." Step 4 On the Preview interface, click . 4.1.9 Snapshot and Recording Settings Store in USD Flash Drive Step 1 On the Preview interface, click . The Snap & Record interface is displayed. See Figure 4-14.
Parameter Description Select resolution. Resolution When video resolution is ﹥ the set resolution, snapshot image adopts the set resolution. When video resolution is ﹤ the set resolution, snapshot image adopts actual video resolution. USB|FTP USB is enabled for storage by default. Format Click this button to format USB flash drive. Click this button to select snapshot storage path. See Figure 4-15. Click to return to the upper level of folder. Click to create a folder.
Figure 4-16 Snap & Record Step 2 In the USB|FTP drop-down list, select FTP. The FTP interface is displayed. See Figure 4-17. Figure 4-17 FTP Step 3 Click to enable FTP storage. Step 4 Configure parameters. For details, see Table 4-3. Table 4-3 Snap & record parameter (FTP) Parameter Description Snap It supports only 1 snapshot at present.
Parameter Description Select resolution. Resolution When video resolution is ﹥ the set resolution, snapshot image adopts the set resolution. When video resolution is ﹤ the set resolution, snapshot image adopts actual video resolution. USB|FTP Select FTP. Address Set FTP address. User Name FTP user name. Password FTP login password. Directory Set directory name. Test Click this button to test whether FTP is available. Step 5 Click OK. 4.1.
Figure 4-19 Playback of recorded video 4.2 Playback Play back the recorded videos. Step 1 On the main interface, click Playback. The Playback interface is displayed. See Figure 4-20. Figure 4-20 Playback (2) Step 2 Select playback device and channel, configure time and click Playback. The system starts to play back recorded videos. See Figure 4-21.
Figure 4-21 Playback of recorded video During playback, you can control the playback speed, download the video and display the video on the TV wall. For details, see Table 4-4. Table 4-4 Playback icon description Icon Description Icon Description Download the video to With HDMI port, display the video USB flash drive. onTV wall and then view the video. Clip the video and saveit to USB flash Configure the play time. drive. The playback is paused during clipping.
Figure 4-22 Playback (3) Click Detect to search external USB flash drive. Click Format to format the storage device, and all files in the storage device will be cleared. Please be careful. 4.3 TV Wall In platform TV wall mode, it does not support calling with F1 number. Control decoder, matrix and TV wall. Devices can be added only through WEB client. For details, refer to "4.3.1 Adding TV Wall through Matrix Web Interface" and "4.3.2 Adding TV Wall through Decoder Web Interface.
This part also applies to TV wall device. Step 1 Enter IP address of matrix at address bar of the browser, and then press Enter. Matrix login interface is displayed. See Figure 4-23. Figure 4-23 Matrix login interface Step 2 Enter username and password. Step 3 Click Login to enter web interface. 4.3.1.1 Adding Network Signal Search or add network signals manually. Step 1 Select Setup > Signal Management > Network Signal. The Network Signal interface is displayed. See Figure 4-24.
4.3.1.2 Signal Group Select Setup > Signal Management > Signal Group. The Signal Group interface is displayed. See Figure 4-25. Devices in the device list can be added to group list. Figure 4-25 Signal group 4.3.1.3 Adding Video Wall Step 1 Select Setup > Display Management > Video Wall Setup. The Video Wall Setup interface is displayed. See Figure 4-26. Figure 4-26 Video wall setup Step 2 Click Add Video Wall to add. 4.3.
Figure 4-27 Login interface of decoder Step 2 Enter username and password. Step 3 Click Login to enter web interface. 4.3.2.1 Adding Remote Device Search or add network signals manually. Step 1 Select Settings > Remote Device. The Remote Device interface is displayed. See Figure 4-28. Figure 4-28 Remote device Step 2 Add a remote device. Click Device Search to show search results, select the needed device and click Add. Click Add to set parameters in the pop-up dialog box. 4.3.2.
4.3.3 Adding Device Add TV wall, matrix and decoder device at the network keyboard. Refer to "3.6 Adding Device" for details. 4.3.4 Video on Wall Step 1 On the main interface, click TV Wall. The TV Wall interface is displayed. Step 2 In the pull-down list, select TV wall. See Figure 4-29. Figure 4-29 TV wall (screen) Step 3 Click one screen in Figure 4-29, such as MON:1. Step 4 Split the screen. Click , enter the line and column numbers, and customize the splicing. Maximum splicing is 20×20.
Figure 4-30 TV wall (screen information) Switching Main and Sub-stream Click to switch main and sub-stream. M represents main stream, while S represents sub-stream. Please switch the stream, and then drag the video onto the TV wall. Clearing Screen Click to clear screen. 4.3.5 TV Wall Icon Description Refer to Table 4-5 for icon description.
Icon Description Icon 16-split Description Custom split Select one window or all windows on the screen. PTZ This button is used with deletion button. Switch main and sub-stream. M represents main stream, while S Delete represents sub-stream. Display the video on the wall quickly. Detailed information about channel. Refer to "4.1.3 Video on Wall" for details. Display signal group. Display all input channels. Refer to "4.3.1.2 Signal Group" for new signal group. Start or stop the scheme patrol.
Figure 4-31 Add task Step 3 Enter task name. Step 4 Click . 4.3.8 Configuring TV Wall On the TV Wall interface, click to enter TV Wall interface. See Figure 4-32. Figure 4-32 Configure TV wall Enable TV Wall Click to enable TV Wall. Then, TV Wall pull-down list in Figure 4-29 will display this TV wall. If decoding channel of this TV wall is bound to other TV walls, other TV walls will be disabled.
New TV Wall Step 1 Click . The New TV Wall dialog box pops up. See Figure 4-33. Figure 4-33 New TV wall Step 2 Enter the name, select line and column, and then click . Step 3 Drag decoding channels on the right into the screen to bind them. Step 4 (Optional) Select two or more screens, and then click to merge them into one screen. Step 5 Click . Delete TV Wall Click to delete TV wall. Cancel Merged Screen Select a merged screen and then click .
Figure 4-34 Edit TV wall Return to TV Wall Interface Click Return to return to TV wall interface. Exit TV Wall Interface Click to exit TV wall interface. 4.4 Platform The network keyboard can connect to a platform, and thus control the devices that are added to the platform. At present, the supported platforms include DSS, DSS-PRO, DSS-C9100 and DSS-Express. DSS platform does not support platform channel preview at present. Key module is not supported in platform preview mode. 4.4.
Figure 4-35 Platform server login interface (DSS-PRO) Step 2 Enter username and password. The default username is system and default password is admin123. Click Login. Main interface of platform server is displayed. See Figure 4-36. Figure 4-36 Main interface of platform Step 3 Click and select Device on the New Tab interface. The system will display the Device interface. See Figure 4-37.
Figure 4-37 Device Step 4 Click Add. The interface is shown in Figure 4-38. Figure 4-38 Add a device (1) Step 5 Select Protocol, Manufacturer, Add Type, Device Category, Organization, Video Server, input IP Address, Device Port and Username/Password. The parameters vary with the selected protocols. The actual interface shall prevail.
In the Add Type dropdown list, When IP Address is selected, enter device IP address. When Auto Register is selected, enter device registration ID. Add encoders through auto register; the ID of auto register has to be in accordance with the registered ID configured at encoder. When Domain Name is selected, the options are from the configured domain during deployment. Step 6 Click Add. The interface is shown in Figure 4-39.
Figure 4-40 Video wall configuration interface Step 2 Click Add Video Wall. The Add New Video Wall interface is displayed. See Figure 4-41. Figure 4-41 Add a video wall Step 3 Enter Video Wall Name, select window distribution. Step 4 Click Select Channel. The Select decode channel interface is displayed. See Figure 4-42.
Figure 4-42 Select a decoding channel It can set if it displays ID in the screen, ID has been disabled; click the icon and it becomes means that the screen , and then it means that screen ID has been enabled. Step 5 Click Done. 4.4.2 Video on Wall Step 1 On the main interface, click Platform. The connection interface of keyboard operation platform is displayed. See Figure 4-43.
Figure 4-43 Connect keyboard operation platform Step 2 Set parameters. Refer to Table 4-6. Table 4-6 Platform parameter description Parameter Description No. Customize platform number. Type Select platform type, including DSS (the old version before DSS-PRO), DSS-PRO, DSS-C9100 and DSS- Express. IP Enter IP address of platform. Set port number. Port Regarding DSS platform, default port number is 9000. Regarding DSS-PRO and DSS-Express platform, default port number is 80.
Figure 4-44 Platform (1) Step 5 Click one screen in Figure 4-44, such as MON:500. Enter display screen information interface. Step 6 Split the screen. For example, click Click to get 16-split screen. , enter the line and column numbers, and customize the splicing. Maximum splicing is 20×20. Step 7 Drag video source on the right onto large screen. See Figure 4-45. Figure 4-45 Platform (2) Step 8 Click .
Switch to live view interface. See Figure 4-46. Figure 4-46 Live view Switching Main Stream and Sub-stream Click to switch main and sub-stream. M represents main stream, while S represents sub-stream. Please switch the stream, and then drag the video onto the TV wall. Clearing Screen Click to clear screen. For other operations of TV wall, please refer to "4.1.3 Video on Wall." DSS-PRO, DSS-C9100 and DSS- Express platforms do not have this icon. The layout is cleared after each split. 4.4.
Icon Description Icon Description Return Maximize and restore the window. Single split 4-split 9-split 16-split Custom split. PTZ Select one window or all windows on the screen. Switch main and sub-stream. M represents main stream, while S This button is used with represents sub-stream. deletion button. Delete Switch to live view interface. Detailed information about input channel. Switch to TV wall mode. 4.4.4 PTZ Control Refer to "4.5 PTZ Control." 4.4.5 Adding Task Refer to "4.3.
Figure 4-47 PTZ control Table 4-8 PTZ control parameter description Parameter Description It consists of fixed step and variable step. Step type By selecting Fixed, the step remains unchanged when PTZ turns; it is always the set step value. By selecting Variable, the step changes with the tilt of joystick. The larger tilt angle represents quicker turning speed. 8 direction keys Control turning direction of SD lens. Zoom Set the zoom increase/decrease of PTZ lens.
Figure 4-48 Call Enter a number in the input box, such as 1. Click Preset to call the preset point 1. It will be called successfully after you have set preset point. Call methods of scan, tour and pattern are the same as that of preset point. Refer to "4.5.2 Settings" for details. 4.5.2 Settings 4.5.2.1 Settings of Preset Point Step 1 Step 2 Step 3 Step 4 Turn the camera to required position with the joystick or direction button. Select Preset.
Click Del Preset to delete the preset point from this tour route. Repeat the operation to delete multiple preset points from this tour route. Preset points cannot be deleted in some protocols. Click Del Tour to delete the present tour route. 4.5.2.3 Settings of Pattern Step 1 Step 2 Step 3 Step 4 Select Pattern. Enter pattern no. in Pattern No. input box. Click Start Pattern to carry out operations of zoom, focus, iris or direction. Click Stop Pattern to complete the settings of one pattern route.
Refer to Table 4-9 for introductions to icons. Table 4-9 SD menu parameter description Parameter Description Direction key Select PTZ menu options. OK key Confirm operations. Click to open PTZ menu on preview interface. Then, use direction key to select different functions to operate the PTZ. PTZ menu Click to close PTZ menu on preview interface. 4.5.4 Auxiliary Function Figure 4-50 Auxiliary function Auxiliary function includes Single Light, Multi-light and Wiper.
4.6.1 Device Management 4.6.1.1 Adding Device Refer to "3.6 Adding Device." 4.6.1.2 Input Channel Display input number, channel, channel name, device, IP address and details. Meanwhile, modify input channel number. On the Settings interface, click Device, and then click Input Channel tab. The Input Channel interface is displayed. See Figure 4-51. Figure 4-51 Input channel Modifying Input Channel Number Click to modify input channel number and name in the pop-up dialog box. 4.6.2 General Settings 4.6.2.
4.6.2.2 Wi-Fi Refer to "3.5.2 Wi-Fi" for details. 4.6.2.3 Bluetooth Step 1 On the General interface, click Bluetooth tab. The Bluetooth interface is displayed. Step 2 Click to enable Bluetooth. Step 3 Click to search nearby Bluetooth device. Step 4 Double-click the searched device and the system will display Connecting. After several seconds, the system will display Connected, so it is connected successfully. See Figure 4-52. Figure 4-52 Bluetooth 4.6.2.
Figure 4-53 Serial Step 2 Set the parameters. Refer to Table 4-10. Table 4-10 Serial port parameter description Parameter Address Description In case of serial port control, identify devices according to the address. Value ranges from 0 to 255. Baud rate Baud rate ranges from 1200 to 115200. There are 8 levels available. Data bit Select data bit, including 5, 6, 7 and 8. Stop bit Select stop bit, including 1 and 2. Parity Select parity, including none, odd, even, checkmark and null parity.
Figure 4-54 General Step 2 Set the parameters. Refer to Table 4-11. Table 4-11 General parameter description Parameter Description Name Set network keyboard name. Language Select language. Date Set date. Time Set time. Format Set time format, including 24-hour and 12-hour. Separator Excel Set date separator, including ".", "-" and "/". When it takes effect, system time is displayed as "2019.10.17", "2019-10-17" and "2019/10/17". Excel config file import separator. It is comma by default.
Figure 4-55 Hardware Step 2 Set the parameters. Refer to Table 4-12. Table 4-12 Hardware parameter description Parameter Description Volume Adjust the volume. It is 0 by default. Keyboard lock After keyboard is locked, log in to the device again to enter it. Step 3 Click Save. 4.6.2.7 MAC Add MAC through key module, and then execute continuous action groups according to the adding sequence. On the local preview interface or TV wall interface, press number key + F2 to call MAC.
Figure 4-56 MAC Step 2 Click Add. The MAC Settings interface is displayed. See Figure 4-57. Figure 4-57 MAC Settings (1) Step 3 Enter Macro Name, which can be free combination of no more than 15 letters and numbers. Step 4 Create MAC with key module. For example, on the key module, press [5+MON+4+MULT+1+WIN+123+ CAM+1+GOTO]. The corresponding interface is displayed. See Figure 4-58. You can switch and call the presets.
Figure 4-58 MAC Settings (2) Step 5 Click Return. Relevant Operation Select a MAC, and then click Delete to delete the MAC. Select a MAC, and then click Detail to view detail. 4.6.3 Account 4.6.3.1 Role In the whole network, users might have different permissions to access network keyboard. You can classify users with the same permission into one role, and thus maintain and manage user information conveniently. Then, you can add, delete and modify role. Select Settings > Account > Role.
Figure 4-59 Role Adding Roles Default admin of the system cannot be deleted. Admin has the highest authority by default. Step 1 Click . The Add roles interface is displayed. See Figure 4-60. Figure 4-60 Add roles Step 2 Set Role name and Role rank. There are 8 role ranks. The number 1 rank is the highest, only second to default admin. It drops from number 1 to number 8.
Step 3 In System authority, select role authority to operate the system. Tick the check box to enable the authority. Tick All to select all authorities. Step 4 Configure operation authority of device input channel. 1) Click Input Channel. The Input Channel interface is displayed. See Figure 4-61. Figure 4-61 Input channel 2) Click . The Add channel interface is displayed. See Figure 4-62. Figure 4-62 Add channel 3) Tick the check box of corresponding channel, and click OK.
Click Group to divide the input channels into groups. Step 5 Click Return to return to Add roles interface. Step 6 Click to save the settings. Deleting Roles Step 1 Tick the check box of corresponding role. Step 2 Click Delete. The Message dialog box pops up. Step 3 Click OK to finish. Modifying Role Step 1 Click corresponding to the role. The Modify role interface is displayed. See Figure 4-63. Figure 4-63 Modify role Step 2 Modify role information according to actual needs.
Figure 4-64 Account Adding User Default admin of the system cannot be deleted. Admin has the highest authority by default. Create a role before adding account. Step 1 Click . The Add user interface is displayed. See Figure 4-65. Figure 4-65 Add user Step 2 Set User Name, enter New and Confirm, and select Subordinate Role. New and Confirm shall be the same. Step 3 Click to save the settings.
Deleting User Step 1 Click the user that shall be deleted. Step 2 Click Delete. The Message dialog box pops up. Step 3 Click OK to finish. Modifying Password Step 1 Click corresponding to the user. The Modify user interface is displayed. See Figure 4-66. Figure 4-66 Modify user Step 2 Enter old password, and set a new password. Step 3 Click to save the settings. 4.6.4 System 4.6.4.1 Version Upgrade Upgrade the device with flash drive. Step 1 On the System interface, click Upgrade tab.
Figure 4-67 Upgrade Step 2 Insert flash drive into the network keyboard, and click USB Check. Step 3 Click Choose File to upgrade. The keyboard will restart automatically after upgrade. 4.6.4.2 Configuration You can import or export system configurations. Step 1 On the System interface, click Config tab. The Config interface is displayed. See Figure 4-68.
Step 2 Insert flash drive into the network keyboard, and click USB Check. Detect all connected USB and capacity. Step 3 Import or export configurations. Import: Import config information in flash drive into the network keyboard. Export: Export config information in the present keyboard to flash drive. Click Format to format the storage device, and all its files will be cleared. Operate cautiously. 4.6.4.
Step 1 On the System interface, click LOG tab. The LOG interface is displayed. See Figure 4-70. Figure 4-70 Log Step 2 Enter Start Time and End Time. Step 3 Select Type. Step 4 Click Search. The found logs are displayed. See Figure 4-71. Figure 4-71 Search log Relevant Operation Click to view log details. Click Clear to clear all the logs. Be careful.
4.6.4.5 Device Information You can view S/N and MAC address of the network keyboard. On the System interface, click Device Information tab. The Device Information interface is displayed. See Figure 4-72. Figure 4-72 Device information 4.7 Extension Control the devices with direct physical connection with network keyboard. At present, it only supports to control speed dome with RS–485 port. Step 1 On the main interface, click Extension. The Analog interface is displayed. See Figure 4-73.
Figure 4-73 Analog (1) Step 2 Set the parameters. Refer to Table 4-13. Table 4-13 Analog keyboard parameter description Parameter Description Connection mode Set the connection mode, which only supports RS–485 at present. Device type Enter device type. Address Enter device address. Select the protocol, including SD1, PELCOD and PELCOP. Protocol AA-SD1 is the same as SD1, AA-PELCOD is the same as PELCOD, and AA-PELCOP is the same as PELCOP.
Figure 4-74 Analog (2) System Configurations 74
Appendix 1 Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. Below are some tips and recommendations on how to create a more secured security system.
5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Change Default HTTP and Other Service Ports We suggest you to change default HTTP and other service ports into any set of numbers between 1024~65535, reducing the risk of outsiders being able to guess which ports you are using. Enable HTTPS We suggest you to enable HTTPS, so that you visit Web service through a secure communication channel.
The network should be partitioned and isolated according to the actual network needs. If there are no communication requirements between two sub networks, it is suggested to use VLAN, network GAP and other technologies to partition the network, so as to achieve the network isolation effect. Establish the 802.1x access authentication system to reduce the risk of unauthorized access to private networks.
Legal and Regulatory Information Legal Considerations Video surveillance can be regulated by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes. Disclaimer Every care has been taken in the preparation of this document. Please inform your nearest Dahua office of any inaccuracies or omissions.
Technology. The most up to date copy of the signed EU Declaration of Conformity (DoC) can be downloaded from: www.dahuasecurity.com/support/notice/ CE-Electromagnetic Compatibility (EMC) This digital equipment is compliant with Class A according to EN 55032. Warning: This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.
Technology Equipment. CAUTION This is a Class A equipment. Operation of this equipment in a residential environment could cause radio interference. In such a case, the user may be required to take corrective actions. Batteries Correct disposal of batteries in this product This marking on the battery indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life.
to local laws and regulations. For information about your nearest designated collection point, contact your local authority responsible for waste disposal. In accordance with local legislation, penalties may be applicable for incorrect disposal of this waste. This symbol means that the product shall not be disposed of together with household or commercial waste. Directive 2012/19/EU on waste electrical and electronic equipment (WEEE) is applicable in the European Union member states.
response. If you are connected to the Internet, you can: Download user documentation and software updates. Search by product, category, or phrase. Report problems to Dahua support staff by logging in to your private support area. Chat with Dahua support staff. Visit Dahua Support at www.dahuasecurity.com/support Contact Information ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. Address: No.1199, Bin'an Road, Binjiang District, Hangzhou, P.R.
device for specific working temperature and humidity. Do not place the device in a location exposed to dampness, dust, extreme hot or cold, strong electronic radiation, or unstable lighting condtions. Do not install the device in a place near the heat source, such as radiator, heater, furnace, or other heat generating device to avoid fire. Prevent liquid from flowing into the device to avoid damge to internal components.
Symbol WSKAZÓWKI UWAGA Znaczenie Oznacza wskazówki pozwalające na rozwiązanie problemu lub oszczędność czasu. Oznacza informacje uzupełniające tekst główny. Wymogi dot. Bezpieczeństwa Przestrzegaj lokalnych standardów bezpieczeństwa elektrycznego celem upewnienia się, że źródło napięcia jest stabilne i zgodne z wymogami określonymi dla urządzenia. Urządzenie należy transportować, używać i przechowywać w warunkach o dozwolonym poziomie wilgotności i temperatury.
Sikkerhedsanvisninger Følgende signalord med beskrivelse kan forekomme i vejledningen. Signalord Beskrivelse FARE Angiver høj risiko, som, hvis den ikke undgås, kan medføre død eller alvorlig personskade. ADVARSEL Angiver middel eller lav risiko, som, hvis den ikke undgås, kan medføre lettere til moderat personskade. FORSIGTIG Angiver mulig risiko, som hvis den ikke undgås, kan resultere i skade på ejendom, tab af data, reduceret ydelse eller uforudsigelige resultater.
Bortskaf brugte batterier i overensstemmelse med lokale bestemmelser eller batteriproducentens anvisninger. Suomi Tärkeitä varotoimenpiteitä ja varoituksia Tässä luvussa kuvataan laitteen asianmukainen käsittely, vaarojen torjunta ja omaisuusvahinkojen estäminen. Lue tämä sisältö huolellisesti ennen laitteen käyttämistä ja noudata näitä ohjeita, kun käytät laitetta. Säilytä ohjeet tulevia tarpeita varten.
Paristo Alhainen pariston varaustaso vaikuttaa tosiaikakellon (RTC:n) toimintaan nollaten sen jokaisella käynnistyskerralla. Lokiviesti ilmestyy tuotteen palvelinraporttiin, kun paristo on vaihdettava. Lisätietoa palvelinraportista saat tuotteen asetussivuilta tai ottamalla yhteyttä Dahuan tukeen. VAROITUS Räjähdysvaara, jos paristo asetetaan väärin paikalleen. Vaihda vain samanlaiseen paristoon tai Dahuan suosittelemaan paristoon.
A tűz elkerülése érdekében ne telepítse az eszközt hőforrás, mint például radiátor, hősugárzó, kemence, vagy más hőtermelő eszköz közelében lévő helyre. A belső alkatrészek károsodásának elkerülése érdekében akadályozza meg, hogy folyadék folyjon az eszközbe. A leesésének megakadályozása érdekében az eszközt vízszintesen telepítse, vagy stabil helyre telepítse. Az eszközt jól szellőző helyre telepítse, és ne blokkolja az eszköz szellőzését. Önkényesen ne szerelje szét az eszközt.
Сигнални думи Значение СЪВЕТИ Обозначава начини, които да ви помогнат да разрешите проблем или да спестите време. ЗАБЕЛЕЖКА Предоставя допълнителна информация като акцент и допълнение към основния текст. Изисквания за безопасност Спазвайте местните стандарти за електрическа безопасност, за да осигурите стабилно напрежение, отговарящо на изискването за захранване на устройството.
Dispozitivului Instructiuni de siguranta Urmatoarele semne categorizate pot aparea in Ghid. Signal Words PERICOL AVERTIZARE ATENTIE SFATURI NOTA Meaning Indică un risc potențial ridicat care, dacă nu este evitat, va duce la deces sau vătămări grave. Indică un pericol potențial mediu sau scăzut care, dacă nu este evitat, poate duce la răni ușoare sau moderate.
AVERTIZARE Risc de explozie dacă bateria este înlocuită incorect. Înlocuiți numai cu o baterie identică sau cu o baterie recomandată de Dahua. Aruncați bateriile uzate în conformitate cu reglementările locale sau cu instrucțiunile producătorului bateriei. Čeština Důležitá bezpečnostní opatření a varování Tato kapitola popisuje obsah vztahujícíse na správnou manipulaci se zařízením, prevenci nebezpečí a prevenci škod na majetku.
Zařízení instalujte na dobře větraném místě a neblokujte odvětrávání zařízení. Zařízení svévolně nedemontujte. Během přepravy, skladování a instalace zamezte silnému tlaku, prudkým vibracím a namočení. Při přepravě je nezbytné úplné zabalení. Při přepravě použijte obal z výroby nebo obdobnýobal. Baterie Nízké nabití baterie ovlivňuje fungování hodin ve skutečném čase a způsobuje, že se při každém spuštění resetují.
Σήματα με λέξεις ΣΥΜΒΟΥΛΕΣ ΣΗΜΕΙΩΣΗ Σημασία Παρέχει μεθόδους που θα σας βοηθήσουν να επιλύσετε ένα πρόβλημα ή να εξοικονομήσετε χρόνο. Παρέχει πρόσθετες πληροφορίες δίνοντας έμφαση και συμπληρώνοντας το κείμενο. Απαιτήσεις ασφαλείας Τηρήστε τα τοπικά πρότυπα ηλεκτρικής ασφάλειας για να βεβαιωθείτε ότι η τάση είναι σταθερή και συμμορφώνεται με την απαίτηση τροφοδοσίας της συσκευής.
hrvatski Važne zaštitne mjere i upozorenja Ovo poglavlje opisuje sadržaj koji obuhvaća pravilno rukovanje uređajem, sprječavanje opasnosti i sprečavanje oštećenja imovine. Pažljivo pročitajte ove sadržaje prije korištenja Uređaja, pridržavajte ih se pri upotrebi i sačuvajte ih za buduću uporabu. Sigurnosne upute U vodiču se mogu pojaviti sljedeće kategorizirane signalne riječi s definiranim značenjem.
zaštitno pakiranje. Koristite tvorničko pakiranje ili ekvivalent za transport. Baterija Niska baterija utječe na rad RTC, uzrokujući da se resetira pri svakom uključivanju. Kad bateriju treba zamijeniti, pojaviti će se poruka u izvješću poslužitelja (server). Dodatne informacije o izvješću poslužitelja (server) potražite na stranicama priručnika proizvoda ili se obratite Dahua podršci. UPOZORENJE Rizik od eksplozije ako se baterija nepravilno zamijeni.
vlhkosti a teploty. Prečítajte si príslušné technické špecifikácie zariadenia pre špecifickú pracovnú teplotu a vlhkosť. Zariadenie neumiestňujte na miesto vystavené vlhkosti, prachu, extrémnemu teplu alebo chladu, silnému elektronickému žiareniu alebo nestabilným podmienkam osvetlenia. Zariadenie neinštalujte na miesto, ktoré sa nachádza blízko zdroja tepla, ako je napríklad radiátor, ohrievač, pec alebo iné zariadenie na tvorbu tepla. Predídete tak vzniku požiaru.
Oznaka UPOZORENJE OPREZ PREPORUKE BELEŠKA Značenje Označava opasnost srednje ili niske potencijale koja bi, ukoliko se ne izbegne, mogla dovesti do blagih ili umerenih povreda. Označava potencijalni rizik koji bi, ukoliko se to ne izbegne, mogao dovesti do oštećenja imovine, gubitka podataka, niže performanse ili nepredvidivog rezultata. Pruža metode za pomoć u rešavanju problema ili uštede vremena. Pruža dodatne informacije kao naglasak i dodatak tekstu.
Türkçe Önemli Kurallar ve Uyarılar Bu Bölüm, Cihazın doğru kullanımını, tehlike önlemeyi ve mal zararının önlenmesini kapsayan içerikleri anlatmaktadır. Cihazı kullanmadan önce bu içerikleri dikkatli şekilde okuyun, kullanırken bunlara uyun ve ileride başvurmak üzere saklayın. Güvenlik Talimatları Aşağıda, belirtilen açıklamaya sahip kategorize edilmiş uyarı sözcüklerini Kılavuzda görebilirsiniz.
Cihazı iyi havalandırılan bir yere monte edin ve cihazın hava sirkülasyonunu engellemeyin. Cihazın parçalarını gelişigüzel sökmeyin. Cihazın nakliyesi, saklanması ve montajı esnasında ağır baskılardan, şiddetli sarsıntılardan ve sıvıya batmalardan kaçının. Cihazın nakliyesi esnasında ambalajın tamamı gereklidir. Nakliye için fabrikasyon ambalajı ya da eş değerini kullanın. Pil Düşük pil gücü, her güç açma esnasında sıfırlanmasına neden olarak RTC’nin çalışmasını etkiler.
סִמון מִלוע התְה משמתוע .ולהשלמתו לטקסט להדגשה נוסף מידע מספקת ִטִחוע דְִשע ותואם יציב שהמתח להבטיח מנת על בחשמל לבטיחות המקומיים התקנים לכל לציית יש .המכשיר של החשמל אספקת לדרישות .המותרים והלחות הטמפרטורה לתנאי בהתאם יעשו המוצר של ואחסון שימוש ,הובלה המוגדרים וללחות לטמפרטורה המכשיר של המקבילים הטכניים למפרטים להתייחס יש .
Précautions d’emploi Les mentions d’avertissement catégorisées suivantes ayant un sens défini sont susceptibles d’apparaître dans le manuel. Mentions d’avertissement DANGER AVERTISSEMENT AVERTISSEMENT Signification Indique un danger à risque élevé qui entraînera la mort ou des blessures graves si les instructions données ne sont pas respectées. Indique une situation moyennement ou faiblement dangereuse qui entraînera des blessures faibles ou modérées si les instructions données ne sont pas respectées.
Batterie Un niveau de batterie faible affecte le fonctionnement du RTC, qui se réinitialisera à chaque redémarrage. Lorsque la batterie doit être remplacée, un message de journal apparaît dans le rapport du serveur du produit. Pour plus d’informations sur le rapport du serveur, consultez les pages de configuration du produit ou contactez l’assistance Dahua. AVERTISSEMENT Risque d’explosion si la batterie est remplacée de façon incorrecte.
correspondientes del dispositivo para la temperatura y humedad operativas específicas. No coloque el dispositivo en un lugar expuesto a humedad, polvo, calor o frío extremos, radiaciones electrónicas fuertes o condiciones de iluminación inestables. No instale el dispositivo en un lugar cerca de fuentes de calor, como radiadores, calentadores, hornos u otros dispositivos generadores de calor, para evitar un incendio.
Signalwörter Bedeutung WARNUNG VORSICHT Weist auf eine mittlere oder geringe potentielle Gefahr hin, die, wenn sie nicht vermieden wird, zu leichten oder mittelschweren Verletzungen führen kann. Weist auf ein potenzielles Risiko hin, das, wenn es nicht vermieden wird, zu Sachschäden, Datenverlust, geringerer Leistung oder unvorhersehbaren Ergebnis führen kann. TIPPS Stellt Methoden bereit, mit denen Sie ein Problem lösen oder Zeit sparen können.
Explosionsgefahr. Ersetzen Sie die Batterie nur durch eine identische Batterie oder eine Batterie, die von Dahua empfohlen wird. Entsorgen Sie leere Batterien entsprechend den örtlichen Vorschriften oder den Anweisungen des Batterieherstellers. Italiano Norme di sicurezza e avvertenze importanti Il presente capitolo descrive le procedure per una corretta manipolazione del dispositivo, per la prevenzione dei rischi e per la prevenzione di danni materiali.
Installare il dispositivo in un ambiente adeguatamente ventilato e non ostruire la circolazione dell'aria. Non smontare il dispositivo in modo casuale. Evitare forte sollecitazioni, violente vibrazioni e non bagnare il prodotto durante il trasporto, lo stoccaggio e l’installazione. Trasportare il prodotto utilizzando un imballaggio adeguato. Utilizzare l'imballaggio standard previsto o un imballaggio equivalente.
Veiligheidsvereiste Houdt u aan plaatselijke veiligheidsstandaarden om ervoor te zorgen dat het voltage stabiel is en voldoet aan de vereiste stroomvoorziening van het apparaat. Transporteer, gebruik en bewaar het apparaat onder de toegestane relatieve luchtvochtigheid en temperatuuromstandigheden. Zie de overeenkomstige technische specificaties van het apparaat voor specifieke werktemperatuur en relatieve luchtvochtigheid.
Palavras-sinal Significado ATENÇÃO Indica um risco potencial elevado que, se não for evitado, resultará em morte ou ferimentos graves. Indica um risco potencial médio ou baixo que, se não for evitado, poderá resultar em ferimentos ligeiros ou moderados. Indica um risco potencial que, se não for evitado, pode resultar em danos materiais, perda de dados, desempenho inferior ou resultados imprevisíveis. SUGESTÕES Disponibiliza métodos para o ajudar a resolver um problema ou a poupar o seu tempo.
