Wireless Keypad User’s Manual ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.
User’s Manual Foreword General This manual introduces the installation, functions and operations of the wireless keypad (hereinafter referred to as the "keypad"). Read carefully before using the device, and keep the manual safe for future reference. Model DHI-ARK30T-W2 (868); DHI-ARK30T-W2 Safety Instructions The following signal words might appear in the manual. Signal Words Meaning DANGER Indicates a high potential hazard which, if not avoided, will result in death or serious injury.
User’s Manual About the Manual ● The manual is for reference only. Slight differences might be found between the manual and the product. ● We are not liable for losses incurred due to operating the product in ways that are not in compliance with the manual. ● The manual will be updated according to the latest laws and regulations of related jurisdictions. For detailed information, see the paper user’s manual, use our CD-ROM, scan the QR code or visit our official website.
User’s Manual Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard protection, and protection of property damage. Read carefully before using the device, and comply with the guidelines when using it. Operation Requirements ● Make sure that the power supply of the device works properly before use. ● Do not pull out the power cable of the device while it is powered on. ● Only use the device within the rated power range.
User’s Manual Table of Contents Foreword ............................................................................................................................................................................................ I Important Safeguards and Warnings ................................................................................................................................ III 1 Introduction .................................................................................................
User’s Manual 1 Introduction 1.1 Overview Wireless keypad is used with alarm hub, and supports multiple users, allowing each one to access the alarm security system with their own private passcode. The system also conveniently keeps a log of the operations performed by each user, making it easy to review and analyze usage history. It is ideal for use in villas, shops, apartments and more. 1.2 Technical Specifications This section contains technical specifications of the keypad.
User’s Manual Type General Parameter Description Operating Temperature –10 °C to +55 °C (+14 °F to +131 °F) (indoor) Operating Humidity 10%–90% (RH) Power Supply 4 × AA batteries Battery Life 3 years (if the device is used to arm and disarm once a day) Product Dimensions 146.0 mm × 82.0 mm × 22.6 mm (5.75" × 3.23" × 0.89") Packaging Dimensions 180.0 mm × 104.0 mm × 58.0 mm (7.07" × 4.09" × 2.28") Installation Wall mount Net Weight 240 g (0.529 lb) (with battery) 145 g (0.
User’s Manual 2 Checklist Figure 2-1 Checklist Table 2-1 Checklist No. Item Name Quantit y No.
User’s Manual 3 Appearance Figure 3-1 Appearance 4
User’s Manual Table 3-1 Structure No. Name Description There are four indicators, including communication, arming and disarming, fault, and alarm indicators. ● All indicators are solid for 2 seconds: Powered on. ● All indicators are off: Not enter paring mode. ● Communication indicator status: Flashes green quickly: Pairing mode. ◇ Sold green for 2 seconds: Pairing successful. ◇ Flashes green 3 times: Pairing fails. ◇ Off: Online.
User’s Manual No. Name Description 4 Back cover When the tamper switch is released, the tamper alarm will be triggered. 5 On/off switch Turn on or turn off the keypad. 6 4 × Batteries Insert batteries to power on the keypad. 7 Tamper switch When the tamper switch is released, the tamper alarm will be triggered.
User’s Manual 4 Adding the Keypad to the Hub Before you connect it to the hub, install the DMSS app to your phone. This manual uses iOS as an example. ● Make sure that the version of the DMSS app is 1.98 or later, and the hub is V1.001.0000000.8.R.220319 or later. ● Make sure that the hub has a stable internet connection. ● Make sure that the hub is disarmed. Step 1 Go to the hub screen, and then tap Step 3 Tap Next after the keypad has been found. Step 2 Step 4 Step 5 Step 6 Tap to add the keypad.
User’s Manual 5 Installation Prior to installation, add the keypad to the hub and check the signal strength of the installation location. We recommend installing the keypad in a place with a signal strength of at least 2 bars. The keypad supports wall mount. Step 1 Loosen the screw to open the keypad. Figure 5-1 Loosen the screw Figure 5-2 Open the keypad Step 2 Insert four batteries into the keypad.
User’s Manual ● If the battery is dead, you need to replace the battery. ● When replacing the battery, make sure that the side marked with "＋" faces the back cover of the keypad. ● Make sure to use the same model when replacing the battery to avoid fire or explosion. ● Make sure not to mix the old batteries with new one. Figure 5-3 Put on the batteries Step 3 Drill four holes in the wall according to the hole positions of the keypad, and then put the expansion bolts into the holes.
User’s Manual Figure 5-5 Close the keypad Step 5 Secure the keypad with screw.
User’s Manual 6 Configuration You can view and edit general information of the keypad. 6.1 Viewing Status On the hub screen, select a keypad from the accessory list, and then you can view the status of the keypad. Table 6-1 Status Parameter Value The status for whether the functions of the keypad are enabled or disabled. Temporary Deactivate ● ● ● Temperature : Enable. : Only disable tamper alarm. : Disable. The temperature of the environment. The signal strength between the hub and the keypad.
User’s Manual Parameter Value Transmit through Repeater The status of whether the keypad forwards its messages to the hub through the repeater. Program Version The program version of the keypad. 6.2 Configuring the keypad On the hub screen, select a keypad from the accessory list, and then tap to configure the parameters of the keypad. Table 6-2 Keypad parameter description Parameter Device Configuration Description ● View keypad name, type, SN and device model.
User’s Manual Parameter Description Enable the keys on the keypad first and set if an event happens. ● Fire Alarm: Enable by default. After enabling the Fire Alarm, when a fire is detected, you need to press and hold the fire key on the keypad for 3 seconds to trigger fire alarms. ● Link Fire Alarm to Siren: Enable by default. After enabling the function, the siren and the buzzer will be linked when fire alarms are triggered. ● Emergency Alarm: Enable by default.
User’s Manual Parameter Description Select from high, low, and automatic. Transmit Power The higher transmission power levels are, the further transmissions can travel, but power consumption increases. If you select Low, the keypad will enter into reduced sensitivity mode. Enable card reader function and soft encryption function on the keypad. ● Card Reader: Enable by default. If enabled, the keypad Card Reader Config supports card recognition function.
User’s Manual 7 User Management 7.1 Adding Users You can add, modify, or delete keypad users when it is disarmed. Only installer and admin users have permission to add users. Procedure Step 1 Step 2 Step 3 Step 4 Go to the home screen. Select a hub, and then select > Device Details > Hub Setting > User Manager. Tap to add a user. Enter your username, passcode, and duress passcode, and then select arming and disarming permissions for the room. ● Passcode and duress code must be 4 to 6 digits.
User’s Manual Related Operations ● Deleting a User On the User Manager screen, select the user, and then swipe left to delete the user. The admin user must be the last to be deleted. ● Modifying User's Information On the User Manager screen, select the user, and then you can modify user's information, including username, passcode, duress code and arming and disarming permission. 7.2 Adding Card You can add, modify, or delete the card when the keypad is disarmed. There are 2 ways to add the card.
User’s Manual Step 4 Step 5 Step 6 Press any key to wake up the keypad. Place the card near the card swiping area of the keypad to enter to the linking process. On the Linked User screen, you can select whether to create a new user, or link the card to the added user. If you select to create a new user, tap Create User. For details on adding a user, see Step 7 "7.1 Adding Users". Tap Completed.
User’s Manual 8 Operations 8.1 Frequently Used Commands Following are frequently used commands for the keypad. Before using the keypad, make sure you have created accounts on the DMSS or COS app. Table 8-1 Command Function Command Global away arming Enter the password + + #. Global home arming Enter the password + + #. No passcode arming Press and hold Global disarming Enter the password + Away arming for a single room Enter the password + * + Room No. + + #.
User’s Manual To arm the system without a passcode, you can enable the No Passcode Arming function first, and then press and hold or . ● To arm a single room, you can enter the relevant arming command. ◇ ◇ If the arming is successful, the arming and disarming indicator light will flash blue 3 times slowly, and then will remain solid, with one short beep.
User’s Manual ◇ ◇ If one or more rooms associated with the card are in the arming status, then all the associated rooms will be disarmed if you swipe the card. If all the rooms associated with the card are in the disarming status, then all the associated rooms will be armed if you swipe the card. 8.5 Searching for the Room Status You are only allowed to search for the status of a single room. ● If your search is successful, the keypad will beep once, and indicator lights will show the room status.
User’s Manual Appendix 1 Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. Below are some tips and recommendations from Dahua on how to create a more secured security system.
User’s Manual The account lock feature is enabled by default, and we recommend you to keep it on to guarantee the account security. If an attacker attempts to log in with the wrong password several times, the corresponding account and the source IP address will be locked. 5. Change Default HTTP and Other Service Ports We suggest you to change default HTTP and other service ports into any set of numbers between 1024–65535, reducing the risk of outsiders being able to guess which ports you are using. 6.
User’s Manual In order to better ensure the safety of device and reduce potential cyber risks, we recommend: ● Disable the port mapping function of the router to avoid direct access to the intranet devices from external network. ● The network should be partitioned and isolated according to the actual network needs.
User’s Manual
Legal and Regulatory I nformation 1 .2.51 .32. 1 52 1 0-001 V2.0.0 Legal Considerations Video s u rve, l lance can be repulated by l aws that vary from cou ntry to ccuntry Check the l aws ,n you r loca region before us,ng th,s prod u ct for s u rve, l lance p u rposes Disclaimer , Restrictions of Haza rdous Substances (Ro HS) Directi ve 2011 /65/EU and its amending Directive (EU) 201 5/863 A copy of the original declaration of oonfonnity may be obtained from Dah u a Technology.
