Wireless PIR–Camera User’s Manual ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.
User’s Manual Foreword General This manual introduces the installation, functions and operations of the wireless PIR–Camera (hereinafter referred to as the "PIR–Camera"). Read carefully before using the device, and keep the manual safe for future reference. Model DHI-ARD1731-W2; DHI-ARD1731-W2 (868) Safety Instructions The following signal words might appear in the manual. Signal Words Meaning DANGER Indicates a high potential hazard which, if not avoided, will result in death or serious injury.
User’s Manual About the Manual ● The manual is for reference only. Slight differences might be found between the manual and the product. ● We are not liable for losses incurred due to operating the product in ways that are not in compliance with the manual. ● The manual will be updated according to the latest laws and regulations of related jurisdictions. For detailed information, see the paper user’s manual, use our CD-ROM, scan the QR code or visit our official website.
User’s Manual Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard protection, and protection of property damage. Read carefully before using the device, and comply with the guidelines when using it. Operation Requirements ● Make sure that the power supply of the device works properly before use. ● Do not pull out the power cable of the device while it is powered on. ● Only use the device within the rated power range.
User’s Manual Table of Contents Foreword ............................................................................................................................................................................................ I Important Safeguards and Warnings ................................................................................................................................ III 1 Introduction..................................................................................................
User’s Manual 1 Introduction 1.1 Overview With its built-in 2-MP HD camera and CMOS image sensor, wireless PIR–Camera detects intrusions and captures high-definition snapshots. It is a wireless passive infrared detector that sends snapshots through the Wi-Fi and Ethernet connection to your phone and ARC (alarm center), for the causes of intrusions to be effectively identified.
User’s Manual Type Parameter Signal Strength Carrier Frequency Communication Distance General Technical Description RF Signal test RF-HD signal test DHI-ARD1731-W2(868): DHI-ARD1731-W2: 868.0 MHz-868.6 MHz 433.35 MHz-434.6 MHz DHI-ARD1731-W2(868): DHI-ARD1731-W2: RF-HD: Up to 300 m (984.25 ft) in an open space RF-HD: Up to 300 m (984.25 ft) in an open space RF: Up to 1,600 m (5,249.34 ft) in an open space RF: Up to 1,200 m (3,937.
User’s Manual Type Parameter Description Two-way Digital Temperature Compensation Yes Scenario Indoor Operating Current 65 μA Alarm Current Day: 170 mA (Avg); 800 mA (Max) Night: 230 mA (Avg); 2.
User’s Manual 2 Checklist Figure 2-1 Checklist Table 2-1 Checklist No. Item Name Quantit y No.
User’s Manual 3 Design 3.1 Appearance Figure 3-1 Appearance Table 3-1 Structure No. Name Description 1 IR light Provides IR light for dark environments. 2 Camera Captures images when an intrusion alarm is triggered. ● Flashes green quickly: Pairing mode or reduced 3 Indicator sensitivity mode. ● Solid green: An alarm event was triggered. ● Solid green for 2 seconds: Pairing successful. ● Slowly flashes green for 3 seconds: Pairing failed.
User’s Manual 3.
User’s Manual 4 Power On Step 1 Loosen the screw to open the PIR–Camera. Figure 4-1 Loosen the screw Figure 4-2 Open the PIR–Camera Step 2 Insert batteries into the PIR–Camera. ● When inserting the batteries, make sure that they are all charged to the same level. ● When inserting the batteries, align the "+" symbols on the battery to those on the PIR–Camera.
User’s Manual Figure 4-3 Insert batteries Step 3 Turn on the PIR–Camera.
User’s Manual 5 Adding the PIR–Camera to the Hub Before you connect it to the hub, install the DMSS app to your phone. This manual uses iOS as an example. ● Make sure that the version of the DMSS app is 1.99 or later, and the hub is V1.001.0000000.8.R.220528 or later. ● Make sure that the hub has a stable internet connection. ● Make sure that the hub is disarmed. Step 1 Go to the hub screen, and then tap Step 3 Tap Next after the PIR–Camera has been found.
User’s Manual 6 Installation 6.1 Field of View Field of view of the PIR–Camera are shown below. When installing and using the PIR–Camera, make sure there are no objects partially or fully obscuring the detector's field of view. Figure 6-1 Field of View 6.2 Installing the PIR–Camera Before installation, add the PIR–Camera to the hub and test the signal strength and RF-HD. We recommend installing the PIR–Camera in a place with a signal strength of at least 2 bars.
User’s Manual Figure 6-2 Drill holes Step 2 Close the PIR–Camera. Figure 6-3 Close the PIR–Camera Step 3 Secure the PIR–Camera with a screw. Figure 6-4 Secure the PIR–Camera : Installation height cannot be higher than 2m.
User’s Manual 7 Configuration You can view and edit general information of the PIR–Camera. 7.1 Viewing Status On the hub screen, select a PIR–Camera from the accessory list, and then you can view the status of the PIR–Camera. Table 7-1 Status Parameter Value The status for whether the functions of the PIR–Camera are enabled or disabled. Temporary Deactivate ● ● ● Temperature : Enable. : Only disable tamper alarm. : Disable. The temperature of the environment.
User’s Manual Parameter Value 24 H Protection Zone Status Active status of the 24 h protection zone. ● ● : Enable. : Disable. Sensitivity Sensitivity level during a shock alarm. Transmit through Repeater The status of whether the PIR–Camera forwards its messages to the hub through the repeater. Program Version The program version of the PIR–Camera. 7.
User’s Manual Parameter Description Configure the number of snapshots that can be taken at a time, the interval and the parameters of the image. ● Tap Times to Take Snapshots, and then select times from 1 to 10. ● Tap Trigger Interval, and then you can select 10, 30, 60, or 120 seconds. Snapshot Config ● Tap Image resolution and Quantity, and then for the image resolution, you can select 1600 × 1200, 1280 × 960, 640 × 480, or 320 × 240. For the image quantity, you can select between 1 and 20.
User’s Manual Parameter Description The system provides you with time to leave or enter the protection zone without alarm. ● Delay Time for Entering Arming Mode: When you enter the zone, if you do not disarm the system before the delay ends, an alarm will be triggered. Delay Time Make sure that the delay time for entering arming mode is no longer than 45 seconds in order to comply with EN50131-1.
User’s Manual Appendix 1 Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. Below are some tips and recommendations from Dahua on how to create a more secured security system.
User’s Manual The account lock feature is enabled by default, and we recommend you to keep it on to guarantee the account security. If an attacker attempts to log in with the wrong password several times, the corresponding account and the source IP address will be locked. 5. Change Default HTTP and Other Service Ports We suggest you to change default HTTP and other service ports into any set of numbers between 1024-65535, reducing the risk of outsiders being able to guess which ports you are using. 6.
User’s Manual In order to better ensure the safety of device and reduce potential cyber risks, we recommend: ● Disable the port mapping function of the router to avoid direct access to the intranet devices from external network. ● The network should be partitioned and isolated according to the actual network needs.
User’s Manual
Legal and Regulatory I nformation 1 .2.51 .32. 1 52 1 0-001 V2.0.0 Legal Considerations Video s u rve, l lance can be repulated by l aws that vary from cou ntry to ccuntry Check the l aws ,n you r loca region before us,ng th,s prod u ct for s u rve, l lance p u rposes Disclaimer , Restrictions of Haza rdous Substances (Ro HS) Directi ve 2011 /65/EU and its amending Directive (EU) 201 5/863 A copy of the original declaration of oonfonnity may be obtained from Dah u a Technology.