Specifications

step.1
Connect Wingman SD to Saturn / Dreamcast / PC via port.
Permanently light of the Console Green LED of Wingman SD
indicates that the connection to the console is successful.
step. 2
Wired Connection:
Connect the Xbox 360 / Xbox One / PS3 / PS4 / Switch wired
controller or game pad to Wingman SD through the USB port. Some
devices with high power consumption, such as the Switch Pro
controller, require an external USB power source for normal use.
Using a X360 wireless controller:
Simply connect the wireless X360 wireless receiver to the Wingman
SD through the USB port.
Using PS3 / PS4 / Switch Pro wireless controller:
After completing the connection according to the instructions of the
Wired Connection, remove the USB cable, and then wake up the PS3
/ PS4 / Switch Pro wireless controller.
step. 3
Check whether the Device Red LED of the Wingman SD is
permanently on. This indicates that the connection is completed.
step.1
Holding the Brook Key on the Wingman SD for 1 second will activate
wireless connection pairing mode. The Wingman SD will engage in
pairing with surrounding Bluetooth devices. The pairing mode will
end if:
A. The connection pairing with the wireless controller is successful.
B. The connection pairing is unsuccessful after 90 seconds.
C. The Brook Key is held for 1 second.
step. 2
Wireless connection records between an Xbox One wireless control-
ler (with Bluetooth function) / Xbox One Series 2 and the Wingman
SD will be erased if a wired connection is used. Wireless connection
re-pairing will be required if wireless connection is used.
step. 3
If Xbox One Elite Series 2 controller is used, please turn o controller
prole settings to prevent interference with Wingman SD’s Turbo or
Remap settings. As Xbox One Elite Series 1 controller is incapable of
turning o prole settings, using Xbox One Elite Series 1 controller
might result in Remap function overlapping.
Connecting to the DeviceLED Display Switch the input mode on SaturnConnection Pairing Supplementary Instructions
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
•Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
•Ambient Operating Temperature ......................0℃ to +50℃
1
7 8 9 10 11 12
3 4 5 6
CONVERTER
SD
X360, X1
Xbox Elite 1, Xbox Elite 2
PS3, PS4, Switch Pro
Saturn
Dreamcast
PC
(X-Input)
The following instructions are based on the Xbox One controller.
For those using other controller, please refer to the Corresponding
Buttons List.
Buttons that can be set as Turbo function buttons include: A, B, X, Y,
LB, RB, LT, RT, LSB, RSB (hereinafter referred to as FK)
Step 1. Enter setting mode:
Press VIEW + Xbox Guide, the Device Red LED of the
Wingman SD will be o.
Step 2. Choosing a FK button: (e.g. Setting A as turbo function)
Hold VIEW, then press A
Step 3. Completing Setting Mode:
Release all buttons, then press MENU to save settings.
Step 4. Exit setting mode:
Press Xbox Guide, the Device Red LED of the Wingman SD
will be permanently on.
Turbo Function Settings
Turbo Function Settings
Step 1. Enter setting mode:
Press VIEW + Xbox Guide, the Device Red LED of the
Wingman SD will be o.
Step 2. Erasing all Turbo function buttons
Press VIEW + MENU
Step 3. Exit setting mode:
Press Xbox Guide, the Device Red LED of the Wingman SD
will be permanently on.
Cancelling Turbo Function
The following instructions are based on the Xbox One controller.
For those using other controller, please refer to the Corresponding
Buttons List.
Buttons that can be remap include: A, B, X, Y, LB, RB, LT, RT, LSB, RSB
(hereinafter referred to as FK)
Step 1. Enter setting mode:
Press MENU + Xbox Guide, the Device Red LED of the
Wingman SD will be o.
Step 2. Choosing a FK button: (e.g. Setting X as A+B)
Press X
Step 3. Choosing button to be set:
Hold VIEW, then press A + B.
Step 4. Completing setting mode:
Release all buttons, then press MENU to save settings.
Step 5. Exit setting mode:
Press Xbox Guide, the Device Red LED of the Wingman SD
will be permanently on.
Step 1. Enter setting mode:
Press MENU + Xbox Guide, the Device Red LED of the
Wingman SD will be o.
Step 2. Erasing all settings for Button Remap Settings.
Press VIEW + MENU.
Step 3. Exit setting mode:
Press Xbox Guide, the Device Red LED of the Wingman SD
will be permanently on.
Button Remap Settings
Button Remap Settings
Cancelling Button Remap Settings
P/N: Wingman SD
M/N: ZPP005B
Console LED
Status
Green LED
Permanently on
Connect to
Saturn
Connect to
Dreamcast
Switching
Method*
Connect to
PC
Red LED
Permanently on
3D Controller Mode
Gamepad Mode
Select+Triangle
PC Connecting
Standard Mode
Arcade Stick Mode
Select+Cross
-
For more details please visit our ocial website at
www.brookaccessory.com
202006V2
LT
LB
RT
RB
Pair button
R
005-102461
FCC ID: 2ADKM005B
*Each Wingman SD can only connect to a single Xbox 360 /
Xbox One / PS3 / PS4 / Switch device. Wingman SD supports
most of the accessories that are compatible with original
factory specifications. To expand the number of supported
accessories, firmware will be updated irregularly.
Console LED
Brook Key
(For Wireless
Registration)
Connect to
Dreamcast
Connect to
Saturn
Device LED
Connect to wired Xbox360 /
Xbox One / PS3 / PS4 / Switch
Pro controller to use. Also
supports relevant Xbox360 /
Xbox One / PS3 / PS4 / Switch
peripheral accessories.
Connect to PC or external
power source
Fighting Stick
Xbox Adaptive
Controller
Xbox 360
Xbox One
Xbox Elite
Xbox 360
wireless receiver
wired
Brook Key
(For Wireless Registration)
Xbox One
(BT Model)
Xbox Elite
Series2
USB Wired/ BT Wireless
SATURN
Dreamcast
PC (X-Input)
PS3/ PS4Switch Pro
* The example of the switching method used PS3 / PS4 controller.
Please refer to the Corresponding Buttons List
when using other controllers.
Device LED
Red LED
Permanently On
Red LED
O
Red LED
Slow blinking
(Once every two seconds)
Red LED
Fast blinking
(Seven times per second)
Red LED
Blinking
(Five times per second)
Status
The connector and the device
are currently connected.
Wired device is not connected.
Wireless device is searching for
connection…
Wireless pairing mode is ON
Searching for pairing
device…
Turbo-Remap button is being
pressed.
Entering Turbo-Remap
Settings.
Corresponding Buttons
D-Pad (U/D/L/R)
Lx / Ly
Rx / Ry
Analog Stick
╳
○
□
△
L1
R1
L2
R2
L3
R3
START
SELECT
PS Key
╳
○
□
△
L1
R1
L2
R2
L3
R3
OPTIONS
SHARE
PS Key
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
START
BACK
Xbox Guide Key
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
MENU
VIEW
Xbox Guide Key
B
A
Y
X
L
R
ZL
ZR
L3
R3
+
-
Home
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
START
BACK
Xbox Guide Key
A
B
X
Y
Z
C
L
R
START
START
A
B
X
Y
L
R
START
START
The default controller input setting of Wingman SD is “3D Control
mode”. When using a standard controller, you can switch to
”Standard mode” manually. The following instructions are based on
the Xbox One controller. For those using other controller, please
refer to the Corresponding Buttons List.
Press VIEW + Y, the Console
Green LED is permanently on.
Press VIEW + A, the Console
Red LED is permanently on.
Switch to “3D Control Mode” Switch to “Standard Mode”
Switch the input mode on Dreamcast
The default controller input setting of Wingman SD is “Gamepad
mode”. When using a arcade stick, you can switch to ”Arcade Stick
mode” manually. The following instructions are based on the Xbox
One controller. For those using other controller, please refer to the
Corresponding Buttons List.
Press VIEW + Y, the Console
Green LED is permanently on.
Press VIEW + A, the Console
Red LED is permanently on.
Switch to “Gamepad Mode” Switch to “Arcade Stick Mode”
(3D Control Mode) (Standard Mode)
(Gamepad Mode) (Arcade Stick Mode)
PS3 PS4 Xbox360 XboxOne Switch PC Saturn Dreamcast
Using Xbox One wireless controller / Xbox One Elite Series 2 controller:
Connect the Xbox One wireless controller (Bluetooth model) or the
Xbox One Elite Series 2 to the Wingman SD and the controller will be
ready for use. When connecting, hold the Brook Key on the Wingman
SD for 1 second to enter wireless pairing mode. Then press the Pair
button on the wireless
controller to begin pairing.
Fast blinking of Device Red
LED of Wingman SD indicates
that pairing is in progress.