Specifications
Contact your local waste disposal department
for recycling coin cell batteries.
Replacing the ZE1 EMG Monitor Battery
1. Find the batte
ry door located on t
he underside
of the sensor po
d
.
2.
Insert a $ qua
rter, £ 20p or € 20c c
oin into the
slot and rotate a
nti-clockw
ise.
3.
When the batte
ry door becomes loo
se, remove
car
efully. The battery will be inside the battery
door when you re
move it.
4.
Wait for around
2
0-30 seconds
5.
Insert a ne
w battery into the battery doo
r slot
w
ith the flat side of the battery facing down.
6. Once the ne
w battery
is in place, reattach the
batter
y door by placing the door o
ver the
markers.
7. Insert the coin used to open th
e battery
door
and rotate clockw
ise until the battery d
oor fits
flush w
ith the sensor pod under-s
ide.
How to pair your ZE1 EMG Monito
r
to a
Bluetooth Smart Phone
1. Download and install your chosen EMG app and
sw
itch smart phone bluetooth ‘ON’.
2.
Open and setting the app on your Smart phone.
3.
Press sensor pod button ON, the LED light w
ill
flash ‘blue’.
4.
Use smart phone EMG app to pair
sensor pod.
When paring success, sensor pod LED light stop
flash’blue’.
How to look after your ZE1 EMG Monito
r
1. After using complete, please detach the
sensor pod from
the arm sleeve a
nd press
sensor pod butto
n ‘OFF’. This w
ill preserve
batter
y life and makes washing th
e arm
sleeve easier.
2.
When washing th
e arm sleeve, only use
standard
washing detergent and
normal
temperatu
re wate
r.
3.
The arm sleeve can be washed in a
washing
machine at 30C f
or no more than 30 washes.
4.
Do not leave the arm sleeve to dry
on a
radiator o
r hot surface as this may
cause
damage to the
electrode sensors.
5.
Do not tumble dry as this will dam
age the
electrode sensor
s.
ZE1
Two Channel EMG Monitor Manual
Compatible apps
How to wear your ZE1 EMG Monito
r
1. Adjust the arm sleeve to fit your arm that
it is tight.
2
. Atta
ch the two sensor pod to the ar
m
sleev
e(see below photo).
3. If necessary moisten the electrodes
using a small amount of water, saliva or
electrode heart rate gel to improve the
conn
ection.
4. The ZE1 uses button to ON/OFF.
User Battery Replacement
WARNING
2chEXGHolter
Do not use a sharp object to remove the
batt
ery
Please keep batteries out of reach of children
Do no put batteries in your mouth. I
f
s
wallowed contact your physician or lo
cal
pois
on control centre immediately.
Replaceable coin cell batteries may contai
n
perchl
orate material and special handlin
g
ma
y apply
. See
www
.dtsc.ca.gov/hazardouswaste/perchlorate
Limited Warranty
The Zentan ZE1 EMG Monitor is covered
by the standard Zentan limited warranty.
For more details please visit:
www.zentan.com.tw
ZE1 EMG Monitor Specification
Operating range
30 – 240 bpm
Battery type
User replaceable
CR2032 3 volts
Battery life
Approximately
100+
hours
Radio frequency
protocol
Bluetooth Low
Energy
Water rating
IPX7 Water
Resistant
Operating
temperature range
From 0C to 50C /
-32F to 122F
Storage
temperature range
From -10C to 60C
/ -14F to 140F
Weight
18 grams
Size
40mm(diameter)*
9.5mm(thickness)
Maximum output
power
4dBm
Contact:
Zentan Technology Co., Ltd.
NO.92, Hsing-Sheng Road, Chia-
Li District, T
ainan City, 72254
Taiwan
CAUTION
sensorpodposition
Troubleshoot:
1. Check from the receiving device's manual that it
supports Bluetooth 4.0 (Bluetooth Smart).
2. Check that you have paired the EMG sensor
with the application
3. Check that you are wearing correctly
4. Check battery be getting empty or not
5. Check receiving device positioned correctly
6. Tried restarting the application and sensor pod.
7. If your receiving device has a bluetooth devices
list, try removing from the list and pairing it
again
8. Try restarting the receiving device to see if it
would help
Still having trouble? You can see contact information
or search http://www.zentan.com.tw/ on the internet
to get help
Operation Frequency : 2.402 – 2.480 GHz
RF Output Power : 4.52 dBm (e.i.r.p.)