Installation and Operating Instructions

ManualsBrandsZENNER USA ManualsElectronicsIoT gateway

English

Installation instructions

IoT gateway indoor

1. General information

3. Installation location

In order to gain optimum LoRaWAN network coverage,

an installation location which is as high as possible is

recommended due to various technological advan-

tages. For example, if an attic is available with potential

installation space, this installation location should be

preferred.

Note:

In stairwells and hallways, the current building

regulations should be checked. It is not permitted to

install the product in the service room of the lift.

After selecting the preferred installation location, you

should test the mobile radio connection in this location

prior to attaching it.

1.1. Intended use

Operational safety is only guaranteed if the product

is used as intended by the manufacturer. No liability

is assumed for damage caused by other applications.

Any modifications are only permitted with approval

from the manufacturer. Otherwise the manufacturer’s

declaration is invalidated.

1.2. Safety instructions

If it is necessary to establish a new power connec-

tion, the installation and commissioning must only be

performed by trained qualified specialists. Only trained

qualified electricians may work on electrical systems.

They must be able to assess the work assigned to them

at all times, detect any potential sources of danger and

adopt appropriate safety measures. The installation

work must only be performed in a de-energised state.

Valid specifications and standards are to be observed.

4. Installation

4.1.

Check whether cables are routed to the selected

installation point.

Note the length of the power cable (range for

socket / junction box).

Mark drilling holes on the wall according to

the hole spacing and use a spirit level (drilling

template attached) (ill. 1).

Drill drilling holes, fit dowels and screws in the

holes (included in scope of delivery).

Attach wall mounting bracket to the wall.

Ensure that the correct side of the wall moun-

ting bracket faces upwards. Pay attention to the

following illustration (ill. 1).

Tip:

In the case of uneven walls, use washers.

4.2.

4.3.

2. Product description

4.4.

2.1. Intended use

The ZENNER IoT Gateways use high-performance Lo-

RaWAN® technology, whose excellent building penetra-

tion and long-range network coverage generally ensure

the connectivity of IoT sensors even under challenging

environmental and installation conditions.

The Indoor Gateway is ideally suited for LoRa network

coverage within a building to receive the values of

sensors, some of which are difficult to access, on

several floors and in basements - without the need for

additional repeaters. The device can be used across

various sectors for a variety of IoT applications and is an

integral part of ZENNER IoT system solutions.

4.5.

⬆

2.2. Scope of delivery

ZENNER IoT Indoor Gateway incl. integrated SIM

Mounting hardware (screws & dowels)

Installation and operating instructions

Declaration of conformity

ill. 1

■

4.6.

Snap the gateway into the wall mounting

bracket. The electrical connection is then

established.

■

⬆

ill. 2

Summary of content (5 pages)

PAGE 1
English Installation instructions IoT gateway indoor 1. General information 1.1. Intended use Operational safety is only guaranteed if the product is used as intended by the manufacturer. No liability is assumed for damage caused by other applications. Any modifications are only permitted with approval from the manufacturer. Otherwise the manufacturer’s declaration is invalidated. 1.2.
PAGE 2
5. Electrical connection 6. Commissioning Gateway with plug-in power supply This variant is operated with a plug-in power supply. The electrical connection can be established by a laymen. Commissioning is performed by inserting the power supply unit. The gateway starts immediately after insertion / connection. The gateway passes through several phases during the boot process, which are indicated by the LEDs. Please observe the following sequence of the four LEDs. LED No.
PAGE 3
English 7. Technical data and performance characteristics ■ Suitable for LoRaWAN® IoT solutions from ZENNER ■ Plug & Play - Simple integration into the ZENNER system landscape through pre-configured software* ■ Compatible with the Gateway Management System (GMS) from ZENNER (remote configuration)* ■ Security patches and software updates are distributed in an automated manner* Technical data Mobile radio N/A LAN RJ45 TX power 8 channels internal antenna max.
PAGE 4
8. Dismantling 8.1. Use a narrow flat head screwdriver to gently lift the far right lug on the assembly plate (wall mounting bracket). 8.2. Carefully pull the gateway downwards with an appropriate level of strength. 8.3. Remove the assembly plate from the wall and replace the gateway for a new one, if required. ill.
PAGE 5
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.