MADE IN ITALY 100% IT IS RECOMMENDED TO READ INSTRUCTIONS BEFORE USING THE PRODUCT. For simplification, the instructions refer to the most advanced models that offer multiple Features. Some models may not have these Features (consult our web site www.zenelli.it).
MADE IN ITALY 100% MADE IN ITALY 100% STANDARD MODEL HAND LOCKINGS 1 8 1. TILT locking. 2. PAN locking by means lever with recovery position (pull rotate) 3. Balance locking by means lever with recovery position (pull rotate) 4. Plate locking by means of Quick Release (QR) lever. 5. Temporary TILT locking by means of Save Lenses lever. 6. Safety locking by means of Save Locking lever. 5 3 12 MAIN FEATURES 9 6 4 7. Levelling bubble. 8. Balancing adjustment safety pin. 9.
MADE IN ITALY 100% MADE IN ITALY 100% SETTING UP OF PLATE REMOVAL OF PLATE Remove Gimbal head (b) and Plate from package (carton box). Insert plate (a) into proper head (b) dovetail (c) Dovetail (c) is shown hereunder (see figure at right). To remove plate (a) from Gimbal head (b) keep stop pin pressed down (see figure hereunder) and carefully withdraw plate (a): a pin b Stop pin will return to its initial position, once plate (a) has been duly withdrawn.
MADE IN ITALY 100% MADE IN ITALY 100% USING QUICK RELEASE LEVER AND SAVE LOCK LEVER (present only in some versions) SETTING UP OF TELEPHOTO – LENS Safety guide rails (see paragraph on QR plates) Save lock lever (shown in red color in above figure) ensures tightness of buckle (shown in orange color in above figure). Save Lock lever will maintain safety, in case of casual opening of lever (shown in blue color in above figure).
MADE IN ITALY 100% MADE IN ITALY 100% QUICK RELEASE LEVER LOCKING ADJUSTMENT CHANGING DIRECTION OF QUICK RELEASE LEVER Not every Arca Swiss profile plate in the market has the same width. Zenelli® Quick Release Lever is equipped with a serrated pin (see pin figure – in purple color at previous pages) suitable to absorb and to undo any small width difference.
MADE IN ITALY 100% MADE IN ITALY 100% TELEPHOTO - LENS BALANCING 4. Vertical and horizontal adjustments allow the proper weight balancing of telephoto - lens. - - Balancing is meant proper, when telephoto lens stands steady in every position. (i.e. it has to stand steady , when set in every possible position ). Adjust telephoto - lens center to be aligned with TILT rotation axis, by means of the proper knob.
MADE IN ITALY 100% - MADE IN ITALY 100% Balancing assembly is to be rotated at about 45° towards yourself and TILT knob is to be tighten (this is the easiest way to operate). Position and maintain up lever (shown in blue color) as shown in previous figure and proceed as follows: SAVE LENSES REMOVAL In order to remove save lenses proceed as follows: - Unscrew screw (indicated by the green arrow hereunder). Position lever ( shown in blue color hereunder) Withdraw lever.
MADE IN ITALY 100% MADE IN ITALY 100% COMPACT VERSION HAND LOCKINGS 1. TILT locking. 2. PAN locking by means lever with recovery position (pull rotate) 3. Balance locking by means lever with recovery position (pull rotate) 4. Plate locking by means with recovery position (pull rotate) 1 5 3 MAIN FEATURES 8 7 5. Arca Swiss dovetail profile. 6. Standard 3/8-16 UNC Tripod plugging. 7. Body made from composite material.
MADE IN ITALY 100% MADE IN ITALY 100% REDUCED VERSION HAND LOCKINGS The left model is the standard model with the reduced plate assembly. The model on the right is the new reduced version, sold directly in this configuration. 1. TILT locking. 2. PAN locking by means lever with recovery position (pull rotate) 3. Plate locking by means of lever with recovery position. 3 1 Balancing Adjustment MAIN FEATURES 4. Levelling bubble. 5. Arca Swiss dovetail profile. 6.
MADE IN ITALY 100% MADE IN ITALY 100% CONVERSION MODEL Balancing Adjustment 2 1 4 Balancing Adjustment Camera-body rotation Mechanical Stop 5 3 Telephoto lens, in this model, is equipped with camera-body rotation system. Functioning of levers and of all other parts is that one of Standard Model (see previous paragraphs). To gather further information on our products visit our Web page at www.zenelli.it.
MADE IN ITALY 100% MADE IN ITALY 100% HAND LOCKING 1. TILT locking. 2. Plate locking by means lever with recovery position (pull rotate) Balancing Adjustment MAIN FEATURES 3. Levelling bubble. 4. Arca Swiss dovetail profile. 5. Body made from composite material. Zenelli® advise against removal of those parts, for which no keys a/o tools are supplied in user’s kit. Zenelli® decline all responsibilities for any damage caused by improper removal of components.
MADE IN ITALY 100% MADE IN ITALY 100% QUICK BUCKLE FOR ECONOMIC MODEL Modify Standard Gimbal head into an economic head is feasible by means of a proper tool. To remove balancing system proceed as follows: 3 holes Buckle can easily be assembled and disassembled by means of 3 screws (as shown above). Necessary tools to perform this operation are supplied in user’s kit. The same when disassembling of QR lever is required. QUICK RELEASE PLATES TO BE USED.
MADE IN ITALY 100% MADE IN ITALY 100% ACCESSORIES GENERAL INFORMATION See our Web site www.zanelli.it for other accessories. Zenelli® suggest the use of original accessories and spare parts. The use of nonoriginal accessories and/or spare parts may cause malfunctioning of the product. Zenelli® decline any responsibility for damages occurred by the non-use of original components and/or spare parts.
MADE IN ITALY 100% BRAND Zenelli® is a young Italian company born in 2013 from the passion for the photo world of the company owner, who had gained experience in the planning and manufacturing of high quality supports for cameras and photographic devices. He developed the idea of manufacturing an innovative Gimbal Head, of attractive design, as light as possible, especially designed for any photographer, both professional and amateur.