Use and Care Manual

35°C
For safety reasons, do not store this product in an environment above 35℃ or
below -10℃ for a long time.
Satellite Battery B6400/4600
User Manual
Power Button
Press for 1 second to turn ON Satellite Battery, press and hold for 3
seconds to turn OFF Satellite Battery.
Briefly press to turn OFF the Power Indicators.
IoT Reset Button
Press and hold for 3 seconds to reset Bluetooth and Wi-Fi connected.
LED Button*
Briefly press to turn ON/OFF LED Light.
Press for 1 second to cycle through LED lighting, ambiance, and SOS modes.
DC Power Button
Briefly press to turn ON/OFF DC Outputs.
* Reset the device: Press IoT Reset Button and LED Button simultaneously
for 3 seconds.
Indicators
5.4 Connect with Another Satellite Battery
A Satellite Battery can be stacked on and connected to another unit. Satellite
batteries stacked onto one another do not require a Battery Cable for connection.
1. Remove the Rubber Strips
from the top of the lower
Satellite.
2. Remove the Protective
Cover from the bottom of
the upper Satellite.
4. Gently align the two units until
all feet are settled into place.
3. Align and place two of the
feet in their proper place.
Tips:
· It's recommended that all Satellite Battery units are turned off before
connection.
· After power on, they will flash (LED Light) 3 times and beep 3 times;
then you can start charging or discharging.
· Do not connect them during charging/discharging process.
· Do not touch the metal pins of the ports with your hands or other objects.
Gently clean them with a dry cloth when necessary.
· Battery Mounting Bracket is optional for fixing all the Satellite Battery
units securely.
5.5 Recharging
The Satellite Battery can be charged via SuperBase V, or via XT90 input
port from a solar panel or car battery. When charging from solar panels or
a car, make sure the XT90 port is set to input mode.
5.6 Firmware Update
When using your Satellite for the first time, please check and update to
the latest firmware. There are two methods:
1) USB Flash Drive via Firmware Update Port
Step 1: Download the latest firmware version onto a USB Flash Drive.
Step 2: Insert the USB Flash Drive into the Firmware Update Port.
Step 3: Satellite Battery will begin update, and the Fault Indicator,
Overload Indicator, and Hot/Cold Indicator will all appear red., Indicators
will turn off when update is complete.
2) Zendure App over-the-air (OTA) update
Read the Zendure App user guide and access the download link here:
https://zendure.com/pages/download-center
Tips:
· Do Not turn off the device during the firmware update .
· Please update the firmware when the capacity is more than 20%, in
order to have enough power to complete the update.
Privacy Policy
By using Zendure Products, Applications and
Services, you consent to the Zendure Terms of Use
and Privacy Policy, which you can access via the
"About" section of the "User" page in the Zendure
App.
6. FAQs
[e-mail]
Read all safety guidelines, warnings and other product information in
this manual carefully, and read any labels or stickers attached to the
product before using. Users take full responsibility for the safe usage
and operation of this product. Familiarize yourself with relevant
regulations in your area. You are solely responsible for being aware of
all relevant regulations and using Zendure products in a way that is
compliant.
Keep this manual for future reference.
The information contained herein is subject to change without notice.
For the latest version, please visit
https://zendure.com/pages/download-center.
DISCLAIMER
CONTENTS
2. Specifications
1. Before You Begin
7. FCC Caution:
1. Before You Begin
2. Specifications
3. Safety Guidelines
3.1 Usage
3.2 Disposal Guide
4. Important Tips
5. Getting Started
5.1 What’s in the Box
5.2 Product Overview
5.3 Connect with SuperBase V
5.4 Connect with Another Satellite Battery
5.5 Recharging
5.6 Firmware Update
6. FAQs
7. FCC Caution
3.2 Disposal Guide
1. When possible, fully discharge the battery before disposing of it. Consult
your local laws on battery recycling and disposal.
2. If the battery cannot be fully discharged due to product failure, contact
a professional battery recycling company for further processing.
3. When disposing of secondary cells or batteries, keep cells or batteries of
different electrochemical systems separate from each other.
General
Weight
Dimensions
Capacity
Wireless Type
≈ 101lbs / 46.0kg
ZDSATB6400 ZDSATB4600
≈ 99lbs / 45.0kg
4,608Wh(90Ah/51.2V)
27.2x11.2x10.8in / 690 x 285 x 274mm
6,438Wh (126Ah/51.1V)
Bluetooth, Wi-Fi
Zendure USA Inc.
Phone: [phone] (US)
Office Hours: Mon - Fri 9:00 - 17:00 PST
Support / Contact: www.zendure.com/support
Website: www.zendure.com
2023
4. Important Tips
It is recommended to use this product in an environment at 15
℃~30℃, away from water, fire and other sharp objects.
For long-term storage, please charge and discharge this product
once every 3 months. That is, discharge the product to 30% first,
and then recharge it to 60%.
60%
If the power of this product is lower than 1% after use, please
charge it to 60% before storing it. Leaving the battery discharged
for a long time can cause irreversible damage to the battery and
shorten the service life of the product.
Do not disassemble the product. When service or repair is required,
please consult official Zendure channels. Improper disassembly or
reassembly may result in a risk of fire or personal injury.
Power Indicators
IoT Indicator
· Waiting for pairing: the indicator flashes
· Connected the indicator is on
LED Indicator
DC Power Indicator
Status Indicators
· Indicates LED ON/OFF
· Indicates DC power ON/OFF
· Indicates Power ON/OFF
· 10 LED indicators, each representing 10%, to
indicate current battery level, SoC (State of
Charge) level and firmware update status.
· Fault: there is some error, please check it in
detail via Zendure App
· Overload: there is overload protection; please
remove the load device
· Hot/Cold: there is high temperature or low
temperature protection, normal operation will
resume automatically after battery reaches
appropriate temperature.
5.3 Connect with Satellite Battery
Can Satellite Battery B6400 (or B4600) connect with SuperBase
V4600 (or V6400)?
No, it can't, as they use different battery types.
How many Satellite batteries can be connected to a single
SuperBase V?
For each SuperBase V, you can connect up to 4 Satellite Battery units.
Can it charge and discharge at the same time?
Yes. It supports pass-through charging.
Can a Satellite Battery be charged with solar panels from a
different brand?
Yes, a Satellite Battery can be charged by other solar panels with voltage
ranging from 12V to 150V; Zendure's 400W Solar Panel has been thoroughly
tested with Satellite Batteries and remains our recommendation.
How do I store my Satellite Battery?
For long-term storage, please charge and discharge this product once
every 3 months. That is, discharge the product to 30% first, and then
recharge it to 60%.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2)This device must accept any interference received, including
interference that may cause undesired operation.
2. any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance of 20cm between the radiator & your
body.
Outputs
Car Outlet (1)
Andersen (1)
12.6V 30A, 378W Max
12.6V 10A, 126W Max
XT90 (1**)
12-60V 10A, 600W Max (App enabled)
3.1 Usage
1. Store product in a cool and dry place.
2. Do not dispose of the product in heat or fire.
3. Do not expose to moisture or submerge it in liquid.
4. Do not use around strong static electricity or magnetic fields.
5. Do not disassemble the product. Consult official Zendure channels when
service or repair is required. Incorrect disassembly or reassembly may
result in a risk of fire or injury to persons.
6. When using the product, please strictly follow the operating
environment temperature range specified in the user manual. If the
temperature is too high, it may result in a fire or explosion; if the
temperature is too low, the product performance may be severely
reduced, or the product may cease to work.
7. Do not block or obstruct the fan during use or place the product in an
unventilated or dusty area.
8. Ensure the product is not hit, dropped, or heavily vibrated. Securely
fasten the product when transporting to avoid damage. If severely
damaged, turn off the power source immediately and discontinue using
the product.
9. If you accidentally drop the product into water during use, please place
it in a safe open area, and stay away from it until it is completely dry.
The dried product should not be used again and should be properly
disposed of according to the Disposal Guide section of this manual.
10. Only clean the ports with a dry cloth.
11. Place on a flat surface to keep the product from falling over. If the
product is overturned and severely damaged, turn it off immediately,
place the battery in an open area, keep it away from people and
combustibles, and dispose of it in accordance with local laws and
regulations.
12. Keep out of reach of children and pets.
3. Safety Guidelines
Inputs
XT90 (1) 12V-150VDC 10A, 600W Max
Battery
Cell Chemistry
Cycle Life
SBS (Semi-solid State Battery) LFP
6,000+ cycles3,000+ cycles
* The temperature figures above refer to ambient temperature.
USB-A Firmware Update with USB Flash Drive
* 378W refers to the combined maximum output power of the Car Outlet and the
Andersen port together.
**The XT90 port is an input by default and can be switched to output via zendure App.
It will reset to input mode any time the device is reset.
ZDSATB6400/4600
5. Getting Started
5.1 What’s in the Box
Rubber Strip
LED Light
Battery Port Male
IoT Reset Button & Indicator
LED Button & Indicator
DC Power Button & Indicator
Car Output
Anderson Output
Power Button & Indicators
XT90 Input
Firmware Update Port
Status Indicators
Battery Port Female
User Manual
Warranty Card
5.2 Product Overview
Satellite Battery Handle Cover
SuperBase V can be connected to a Satellite
Battery for capacity expansion. A Battery Cable
(not included) is needed. One SuperBase V can
connect with up to 4 Satellite Battery units.
Only stack one Satellite Battery on top of the
main unit. Refer to the user manual of the
SuperBase V for detailed instructions.
Tips:
· It’s recommended that both SuperBase V
and Satellite Battery are turned off before
connection.
· Make sure to tighten the screw on both sides
after connecting the battery cable.
· The Satellite Battery icon will show up on the
display after connection; then you can start
charging or discharging.
· Do not connect the SuperBase V to the
battery during charging/discharging process.
· Do not touch the metal pins of the ports with
your hands or other objects. Gently clean
them with a dry cloth when necessary.
· Tightly connect the Battery Cable with
SuperBase V and Satellite Battery. A bad
connection can affect the device's
performance or lead to a fire.
Temperature*
Optimal Operating
Temperature
Discharge Temperature
59°F to 95°F (15°C to 30°C)
-4°F to 140°F (-20°C to 45°C)
Charge Temperature
Storage Temperature
-4°F to 110°F (-20°C to 45°C) 0℉ to 110℉(0°C to 45℃)
14°F to 95°F (-10°C to 35°C)
ZDSATB6400 ZDSATB4600