User´s Manual English Digital Satellite Receiver DX 2202
-2-
Table of Contents 1. General Information ..................................................................... 5 1.1 Main Features.............................................................................................5 1.2 Safety instructions.....................................................................................6 1.3 Unpacking...................................................................................................7 1.4 General Operation of the DX 2202 ..........................
6. General Viewing Functions ....................................................... 20 6.1 Select Channel ......................................................................................... 20 6.2 Previous Channel Recall ......................................................................... 20 6.3 TV & Radio Mode ..................................................................................... 20 6.4 TV & VCR Mode.................................................................................
1. General Information The DX 2202 allows you to view a variety of satellite programs. This user’s guide covers the installation of the DX 2202 and the necessary steps to operate various features. It also explains special features available only in this DX 2202 in detail, and will allow you to take full advantage of these features. 1.1 Main Features • Fully MPEG2, DVB compliant • PIG (Picture In Graphic) support DiSEqC1.
1.2 Safety instructions The following section contains important information relating to operation, place of installation and connecting-up of the receiver. Read these notes carefully before putting the unit into operation. Important notes regarding operation • Extended absence / Thunderstorms Always switch the unit off via its mains switch during periods of extended absence or at the onset of thunderstorms. This also applies to any other equipment attached.
• Solar radiation/heat Do not place the receiver close to radiators nor expose it to direct sunlight. • Grounding The parabolic antenna is to be grounded in accordance with regulations. Here, the relevant German VDE regulations (or equivalent) are to be observed. Connecting up and putting into operation • Attention The following section is intended specifically for the specialist dealer. If you are not carrying out the installation yourself, there is no need to pay any attention to this section.
1.5 Remote Control Unit Key Function Turns power ON/OFF of the DSR. When watching a channel, enables/disables the audio. 0~9 MENU EXIT PR+,PR- Enter number of the required menu item or Select a channel number to watch . Press this key one time to run menu on screen, and call command box. Returns to the previous menu on the menu screen or escape from the menu. When watching a channel, change channels, or moves to the next higher or lower item in the menu.
1.6 Front Panel DX 2202 Figure 2: Front Panel KEY FUNCTION Power Turns on and off the power of the receiver (standby). PR V/Λ When watching, changing to the previous and next channel, or moves to the next higher or lower item in the menu 1.
2. Installation of DX 2202 This section explains the installation of DX 2202. Refer to the manuals supplied with the equipment for the installation of outdoor equipment such as the dish antenna. When adding new equipment, be sure to refer to the related parts of the manual for the installation and be sure you have correctly adjusted the antenna to a satellite. 2.1 Connecting to Antenna and TV Satellite antenna antenna Scart cable cable 2.
2.
3. Menu Information Once you have installed and connected the cables of the DX 2202, the menu is displayed. This menu consists of 4 main menus as shown below. • Channel Manager (chapter 7) • Installation (chapter 4) • Preferences (chapter 5) • Timer (chapter 9) During the installation the OK key confirms a selection and key shows the Drop Down List Box. You can also use the numeric keys on the RCU to enter a numeric value. Use the PR+, PR- key to move up or down from one line to another line.
4. User Installation This menu consists of 5 sub-menus as shown below. • Antenna Settings • Automatic Search • Manual Search • Motor Setting • Factory Default 4.1 Antenna Settings 1. Satellite name: Select first satellite you want. 2. Transponder: Select desired transponder.press OK key will Display a down list box which also let's you select desired transponder. 3. LNB Type: Select you LNB type. 4. Low Freq.(MHz)/High Freq.
4.2 Automatic Search: In this menu after pressing white button you can select NIT Search ON or OFF, as well as only FREE channels, only scrambled channels (CAS) or ALL. Select search channel mode. Than press blue button, the DSR will automatic search as shown below: In this menu, press OK key to confirm satellite, than press Scan key (Blue colour key) on the RCU to search satellite, the screen will display a sub-menu as below: 4.2.
4.3.1 Add Transponder In Manual Search menu, press Add TP key (White colour key) on the RCU, the screen will display a submenu, in this sub menu, you can add the frequency and symbol rate, select Hor or Ver polarization mode to add new transponder. 4.3.2 Delete Transponder Delete TP : If you want to delete a Transponder, please select the Transponder which you want to delete and then press Green button on the RCU. A confirm message box will be displayed. Confirm by YES to delete. 4.3.
Recalculate All Positions : When all the locations of searched satellites are shifted for any reason, you can realign all of them once you adjusted one satellite location. Goto Reference: When you install the motor of DiSEqC 1.2 antenna, you can select this function to move the center of the antenna to 0°. Limit Setting: East West Limit On selecting Limit Setting, the Limit Setup menu will pop up. Pressing the Left key on the RCU continuously will take you to the eastern most point.
5.1.System Options 1. OSD Language: Select OSD language out of about 8 languages. 2. OSD Transparence: Set OSD transparence from 1 to 10. 3. OSD Timeout: Set OSD timeout from 1 Sec to 10 Sec for automaticly fade out OSD. 4. Remote System: You can set to code B if you have a Dual Remote Control FB22 from Zehnder to use different RCU IR codes by pressing SHIFT button. 5.2.AV Setting 1. Screen Ratio: Select 4:3, 16:9 or LetterBox screen ratio depending on your TV screen. 2.
5.5 Parental Control This function allows you lock the channel with a password in order to prevent children from accessing the channel. You can also protect your installed data and information using the Install Lock. How to change the Password:Enter the current password. 2. Select ON of Parental Lock. 3. Enter new password. 4. Confirm your new password entering new password again. Note: Default password is 0000. In case you forgot your personnel password the master code is 2381. How to use Parent Lock 1.
5.6 Software- Update via Satellite Because of continuous changes in DVB broadcasting it is also necessary to update your receivers software to be every time on the height of the time. Therefore Zehnder company offers actual upgrade software files on their homepage www.zehnder-sat.de to download to your receiver through RS 232 interface. But the more easy and convenient way is the „upgrade via satellite“ function offered in the main menu „Receiver Information“ of the receiver.
6. General Viewing Functions The following describes the basic functions of your DX 2202 while watching satellite TV or listening to satellite radio. 6.1 Select Channel If you want to select channel, use CH key on the front panel or PR+, PR- key on the RCU or numeric keys. In addition to the above normal function, DX 2202 provides more convenient channel change function. While watching, press OK key on the RCU. A channel list will be displayed on the left side of the screen.
6.6 Favorite List To call a favorite group list press on the RCU. key You can access the next of 8 favorite groups when you press the BLUE button. The method to group favorite channels is explained in the Favorite Channel (page 23). 6.7 Volume & Audio Control 1. Volume Control To increase or decrease volume, use key on the RCU. Note: DX 2202 has 33 volume levels and this can be controlled from the volume level of your TV. 2. Mute To mute the sound, press Mute button on the RCU.
6.9 Pause the frame Press PAUSE button (Blue button) on the RCU to pause the screen. To bring it back to the normal mode, press PAUSE key once again. 6.10 Zoom details of picture This function allows to zoom into details of a TV picture. 1. To show the zoom marks press ZOOM button (White Button), Pressing the Zoom button repeatly extends the size of the mark picture part. 2. Move the marks to the correct part of the picture by using the arrow buttons. 3. At least press OK to zoom the picture.
6.12 Position If you need to adjust the antenna more key on the RCU and accurately, press the position menu will be displayed. Go to key on the RCU to “Move” and press adjust the motor driven antenna. 6.13 Sat If you searched channels from more than one satellite and want to have a channel list for each satellite, press key on the RCU, a satellite list will be displayed. Select one satellite you want, press OK key on the RCU then you will have a channel list of your choice.
7. Channel Manager DX 2202 provides one of the most powerful channel managing functions in the world. This function not only allows you to watch channels but also do a lot of interesting and useful things. 7.1 Channel Manager Channel manager consists of Edit channel and Set Favorites, which contain similar menu structures. Note: Since the usage of Radio Channel is same as that of TV channel, in this manual only TV Channel manager is explained.
7.4 Rename Channel In the Main Page, press Rename key (white color key) on the RCU. This Rename command allows you to rename the channel. First select the channel to be renamed and press OK key, then a Keypad dialog box will be displayed. Enter the desired name. Check whether the channel name is changed on the channel list. 7.5 Delete Channel In the Channel manager, you can enter Delete CH mode, if you press Delete key (Red color key) on the RCU.
7.7 Favorite Channel When you select channel manager and then Set Favorites menu the list will be shown on screen as name “Favorite”. Press FAV key repeatedly to switch between 8 different favorite groups as News, Sports, Kids, Movies, Music, Science, Fashion. Select your favorite channel and then press OK key. Then will be marked next to your selected channel name. If you want to remove the channel name from the favorite channel list, press OK key once again, then the mark will disappear.
8. EPG (Electronic Program Guide) DX 2202 provides EPG function for you to get access to the TV Guide (or Radio Guide if you are listening to radio channels) that will show the titles and other information of the current and next programs on different channels. The information is only available from the network to which the channel you are watching. To see the EPG data, press EPG key on your RCU when watching a channel. The EPG box will be displayed.
9. Timer In this menu you can program the timer in various ways. This function is one of the strong points of DX 2202. One basic condition for the correct operation of this function is the correct time displayed at the top right of the timer menu window. Time Adjust Usually you get the information real time from the satellite automatically but sometimes they transmit wrong information.
10.
11. Software-Update via RS 232 For this receiver you can download new software from Zehnder homepage http://www. zehnder-sat.de to up-grade your receiver with new operating system and new channel list by using RS232 interface and programm editor „CREdit “ . Find at support area ´Download //Software Update´. Then select respective receiver type. With this software you also can prepare your personal channel list at the PC by sorting, moving, deleting, changing, adding channels in a very easy way. 1.
5. Call “Software_Upgrade” Menu from Main Menu and select „Upgrade Applikation“ 6. You can see file window. Select and open the „rom.bin“ file to be upgraded. 7. During the download, your PC and Front panel of the receiver display the procedure situation. will the receiver 8. After completed Download, automatically writes downloaded data in its Flash Rom. Please wait until it displays “ good ” message on the Front Panel Display.
12. Easy plug-and-play data transfer without PC Below you can find another easy method to upgrade operating software by easy plug-and-play data transfer from one receiver to the other. 1. Notice that both receivers, master and slave, are powered off . 2. Connect one receiver to another receiver by using RS 232 cable. 3. Switch your master receiver to stand-by mode. 4. Turn on the slave receiver by Power ON/OFF and check the front display is "d.000". From now on the slave receiver will be upgraded. 5.
13. Trouble Shooting Problem Possible Causes What To Do The display on the front panel does not light up. Main cable is not connected. Check that the main cable is plugged into the power socket. No sound or picture, but the front panel red light is ON. TheThe SRS-5518-GB Receiver is inis in standby mode. standby mode. No sound or picture. The satellite dish is not pointing at the satellite. No singal or weak signal. Bad picture / blocking error.
Problem Possible Causes What To Do The systen is connected by SCART leads and TV is not in AV/EXT mode. If the system is connected by SCART leads, switch the TV to the appropoate AV input. The systen is connected using RF leads. Check the UHF channel fixed in your system and tune the UHF channel properly. There is interference on your digtal satellite channels.
14. SPECIFICATIONS CPU & Memory CPU Processing Speed Program memory (Flash) Decoding Memory( RAM) CX24142 133MHz 1 Mbyte 8 Mbyte Tuner & Channel Connector 1 IF Loop through Frequency Range Digital Signal Input Level LNB Supply 22KHz Tone DiSEqC Control Demodulation Input Symbol Rate 2 x F-Type, 3/8-32UNEF-2A Yes 950 to 2150 MHz -25 to -65dBm 13.0V / 18.0V (max.400mA), Short Circular Protection Frequency:22 ± 4KHz Version1.0/ 1.
03.06 Änderungen vorbehalten! HEINRICH ZEHNDER GMBH SATELLITEN-EMPFANGSTECHNIK Weierhalden 37/1 D-78144 Tennenbronn / Germany - 36 - Tel. 07729/881-0 Fax 07729/881-72 http://www.Zehnder-SAT.de e-mail: Info@Zehnder-SAT.