User's Manual
AGE12+
Remote controller instruction:
Lithium Battery Notes:
Calibrating:
2206 Z-Wings 1.0
• For parents,please read this user manual together with your
children for your safety.
• Do not touch moving toys.
• Please keep your hair ,clothes or other stuff far away from motors.
Safety warning:
Install Batteries in the Remote Control:
Install the drone battery:
1. Make sure the remote control is turned off.
2. Use a screwdriver to open the baery
compartment. Then insert three AAA
baeries , matching the polaries (+ and –)
marked inside. Use alkaline baeries
for opmal performance.Replace the cover.
1. Open baery compartment.
2. Connect baery with drone connector strict.
3. close baery with compartment top case.
Charge the drone battery:
1. Hold the baery connector ( NOT the cable) and
carefully unplug the baery from the drone.
2. Use the USB charging cable to connect the
baery to a 5V USB power source, such as a
laptop. The red LED on the USB connector flash
when charging.Aer full charged,red LED stay light.
3. A full charge takes about 50 minutes. When the
baery is fully charged,the drone can fly 5~6
minutes.
Aer charging, unplug the USB charging cable. Do
not aempt to overcharge the baery.
Cauon:
• Use only the supplied lithium baery. Using any
other baery may damage the drone.
• Only use the included USB charging cable tocharge
the drone baery.
1. Turn on the drone and remote controller. The LEDs on the drone and on the controller light up.Move the le
throle all the way up with one beep sound, then down with one beep sound to pair the remote control with
the drone.When paired, all LEDs on both the remote control and drone light steadily.
2. Aer pairing, with the drone on the ground, press one buon take off or move the le throle forward to ascend.
To avoid ground air turbulence, fly the drone at least 1 . (30cm) off the ground.One buon take off/landing
again,the drone descend slowly.
3. Forward/backword Trim: If the drone tends to move forward, press backword trim; if iends to move backward,
press forward trim.
4. Le /Right Slide Trim: If the drone tends to slide right,press le trim; if it tends to slide le,press right trim.
5. The right throle can switch high/low speed.press with single beep,the drone switch to low speed flying mode;
press with double beep,switch to high speed.
6. Press and hold the le throle control. The transmier beeps.Move the right steering control to perform flip:
• Front Move lever forward/Back Move lever backward;Barrel roll: Move lever right or le To exit stunt
mode, release the throle before moving the steering control.
7. Press Angle+ or Angle- buon,can adjust drone prow lean to forward or backword.
1. when the drone swerves or moves erracally before taking off,the gyroscope inside
your drone needs calibrang.Do the following:
2. Place the drone on level ground,switch on and pair your drone with the remote
control set to ON posion.Move the throle all the way down and the steering
forward at the same me. Hold this posion unl the drone LED eyes start to blink
rapidly. Then release the controls.
3. The drone LED eyes light steadily. Calibraon is successfully completed, and you are now ready for take off.
• please do not aempt to change or remove the lithium baery yourself.
• Do not dispose of baeries in fire.
• Do not leave baeries in hot places such as an automobile under direct sunlight.
• Do not mix used and new baeries, or install used baeries in other equipment.
• Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium) or (Nickel Metal Hydride) baeries.
• Do not reverse the polarity (posive and negave terminals) of baeries.
• For best results, use type AAA baeries.
• Install only new baeries of the the same type in your product.
• Failure to insert baeries in the correct polarity, as indicated in the baery compartment, may shorten the life
of the baeries or cause baeries to leak.
• Baeries should be recycled or disposed of as per state and local guidelines.
LED
Trim backward
Trim forward
Trim left
Trim right
One-touch take off/land
Descend
Turn
left
Turn
right
Ascend
Slide
left
Slide
right
Forward
Backword
Turn on/Off
Angle-
Angle+
Throttle
Steering
push
( turn mode)
push(high/low speed)
Warning: CHOKING HAZARD –Small parts.
Not for children under3 years.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules.
Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operaon.
2. Changes or modificaons not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15
or the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may casue harmful interference to radio communications, However, there is no guarantee
that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
--- Reorient or relocate the receiving antenna.
--- Increase the separation between the equipment and receiver.
--- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--- Consult the dealer or an experienced radio/ TV technician for help.