User’s Manual ZvSync - EU HD Digital Tuner/Decoder DVB-T / DVB-T2
Notice Warnings Cautions and Notes Throughout the entire user’s manual, pay special attention to the following marks that indicate hazardous situations: Warning Indicates a hazardous situation which could result in serious injury Caution Indicates a situation which could damage the equipment or other apparatus. Note Indicates additional information to make the user aware of possible problems and important information to help understand, use and maintain the installation.
Safety Instructions and Precautions This receiver has been manufactured to comply with international safety standards. Please read the safety precautions carefully. 1. Main Supply (100-240V ~50-60Hz AC) • Operate this product only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to the location where the receiver is to be used, consult your local power company.
7. Ventilation • The slots and openings on the case of the product must be left uncovered to allow for air to pass in and out for proper cooling. • Do not operate the product on soft furnishings or carpet. • Do not stack anything on top of the product. 8. Attachments • Do not use unsupported attachments as these may be hazardous or cause damage to the product. 9. Extraneous Objects • Do not insert anything into the openings of the unit. 10.
Contents 1 Before Using the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.2 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 1.3 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Button Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Programmable Buttons . . . . . . . . . . . .
1 Before Using the Product This section provides detailed descriptions of the product and included accessories. 1.1 Front Panel LED Status Indicator – Indicates state of unit. RED – Power is available, but the unit is DEACTIVATED. GREEN – The unit is powered-up and ACTIVATED. Infrared Jack – Input for installation of the remote infrared sensor. USB – Input for installation of USB storage device used for firmware upgrade or activation of the advanced media functions. Use is strictly optional.
1.2 Rear Panel Aerial/Cable/RF Input – Connect to the antenna for over-the-air reception or to a cable feed for DVB-T reception HD Video Output – The video output most commonly used from the receiver unit. Connect to the HDMI digital input of the display device (typically a television). Both high definition video and digital audio are carried.
1.3 Remote Control The ZvSync receiver/decoder is supplied with a partial learning remote control device. Buttons P1-P5 can be programmed to mimic the functions of a select set of buttons from another remote control unit. The intention is that the TV viewing experience can be controlled from a single handset to include power and volume control of the television set and all other functions directed at controlling the ZvSync receiver/decoder.
Button Definitions Definition Power. Pressing once turns on ZvSync. Again turns it off Key Mute. Disables/Enables audio Reverses playback while in PVR mode Fast Forwards playback while in PVR mode Starts Playback when using PVR mode Back up to division in PVR mode. Pauses playback in PVR mode Advances to division when using PVR mode Displays Electronic Program Guide information Quick channel up and down buttons when watching television programs. Stops playback when using PVR mode.
Programmable Buttons The upper-left portion of the remote houses a set of programmable keys. The intent is to allow for common television functions to be programmed so the user only needs to use a single remote control device to manage their television experience when using the ZvSync receiver/decoder. Keys P1 though P5 can be set to any function the user desires. The labeling is present only to provide visual cues the user may use to help remember which key has been programmed to which function.
To program a key the following sequence shall be executed: Step1: Press and hold the “SET” button for three seconds The RED LED lights immediately when the button is pressed After 3 seconds the LED changes to a very bright state Step 2: Press the key you wish to program (P1-P5) The RED LED changes to a slow flash (1/second) Step 3: Press the key on the remote that you are copying The RED LED performs three quick flashes to acknowledge RED LED turns on solid again.
2 Setup This chapter describes how to connect your ZvSync Receiver to the television and receiving apparatus appropriately. The receiver has various options and interface for connectivity. Select the method appropriate to your application. 2.1 Connecting to an Aerial Should over-the-air reception be desired, connect your antenna to the ZvSync receiver’s ‘RF IN’ jack for over-the-air reception, as follows: 2.
2.3 Connecting to the Television HDMI Cable A connection to the HDMI input of a television, if so equipped, is the recommended method to get visual content on to the displaying television. Both visual content and audio content are carried over the single cable from the ZvSync to the television display. The digital connection presents the highest resolution, sharpest picture possible from the ZvSync receiver.
RCA Cables Certain televisions or applications do not have digital video inputs. If so, then the ZvSync will output standard definition representations of the programming over the CVBS port. Both the CVBS output and the HDTV digital output are active simultaneously. All content will be scaled down to 576i regardless of the incoming resolution prior to being sent out the CVBS port. Pa g e 1 4 | Zv S y n c - EU U s e r ’s M a nual w ww. z eev ee.
2.4 Infrared Remote Control Receiver The ZvSync-EU receiver/decoder is supplied with an external IR receiver. This is in the form of a cable with an IR receiver at the end. The pigtail MUST be installed for the ZvSync to receive commands from the remote and is required for proper operation. By separating the infrared receiver from the base unit, the main body of the ZvSync receiver/decoder can be installed in an unobtrusive location with only the IR sensor showing. Connecting to ZvSync The 3.
Usable Angles The remote control must have a relatively unobstructed “line-of-sight” to the infrared sensor. The usable angles are quite flexible, yielding many possible mounting options. Common is to use the included double-sided tape to mount the IR sensor to bottom or side bezel of the attached television. At the user’s discretion the main body of the ZvSync-EU receiver/decoder may be placed out of sight, providing the proper ventilation considerations are observed. 2.
As supplied, the power supply will likely be delivered with no adapter plate installed. Several different plates are provided for a variety of different AC mains plug types. Select the one appropriate for your AC mains supply outlet (UK shown). Insert the plug into the wall-mount supply body Turn the plate clockwise about 10 degrees until it “clicks” into place Insure that the plate is secure before any attempt is made to plug in to the AC mains.
Connecting Power Supply to ZvSync The wall-mount power supply (included) provides power for the ZvSync receiver. Other methods of powering the ZvSync may void the warranty. The DC input is rated at 5VDC at a maximum peak consumption of 10W, nominal consumption of 6W during operation, and a standby power draw of 0.8W. Pa g e 1 8 | Zv S y n c - EU U s e r ’s M a nual w ww. z eev ee.
3 Installation Wizard If you are using the receiver for the first time, or have restored it to factory defaults, the installation guide menu will appear on your screen.
After exiting the “Installation Guide” screen, the following screen will appear: Use the RIGHT arrow key to navigate to the “Channel Search” page Use the DOWN arrow key to navigate to “Country” Pa g e 2 0 | Zv S y n c - EU U s e r ’s M a nual w ww. z eev ee.
Use the UP arrow to navigate to the “Auto Search” option Use the RIGHT arrow key to activate a channel search A scanning status screen showing the progress of the initial channel scan will appear. Allow the scanning process to run to completion (several minutes).
4 Basic Operation To access the general setup menu, press the “Menu” button. The user will see with this top-level navigation screen. Major categories may be selected by navigating left and right using the arrow keys. Once a category is selected, the options may be explored by navigating down into the page and selecting the appropriate page item. After selecting a page item, “step into” it by navigating to the RIGHT. The function will execute or a sub-menu will be presented with additional options. 4.
Set Favorite Channels You can create a short list of favorite programs/channels that you can easily access. Set Favorite TV Program: (1) Select your desired channel then press the FAV button. A symbol will appear and the channel is marked as a favorite. (2) Repeat the previous step to select more favorite channels. (3) Confirm and exit the menu by pressing the EXIT key.
Delete a TV Program (1) Select the program and then press the BLUE button. A warning message will appear. (2) Press OK to delete the channel (3) Repeat the process if more channels need to be deleted (4) Hit EXIT to complete Lock Program You can lock certain channels for restricted viewing using that particular ZvSync. (1) Select a particular channel and then press the YELLOW button. A lock-shaped symbol is displayed. The channel is now locked from selection.
4.2 Picture Settings The allowed output video settings can be adjusted at the “Picture” top-level settings page. When the HDTV port is connected via HDMI to the display television all the settings are honored. If component video (CVBS) or RF modulation are being used to send the video to the display device the only supported resolution is 576i regardless of the setting on the resolution item.
4.3 Channel Search The “Channel Search” top-level navigation page allows the ZvSync tuner/ decoder to rescan for channels and change settings relevant to the attached reception method. Auto Search Automatically searches for channels and saves them once the scan is complete. All previous entries will be deleted. Select “Auto Search” and press OK or RIGHT arrow to start To cancel press EXIT. Only found channels will be saved.
4.4 Time Setting Time Offset Automatic or manual GMT time offset adjustments. Country Region Select country of interest for use with Auto Time Offset adjustments. Time Zone Time zone when Time Offset is set to manual. Sleep Allows setting of an interval after that the ZvSync will automatically shut off Power On/Off Allows setting a schedule for time-of-day activation and shutdown of the ZvSync device.
4.5 World Option Settings The Option screen allows for setting the On Screen Display language and the audio language to be played if the incoming program allows for those options. Digital Audio Allows setting various types of audio to be output over the HDTV port. Pa g e 2 8 | Zv S y n c - EU U s e r ’s M a nual w ww. z eev ee.
4.6 System Settings Various System Parameters Default user password is ‘000000’. Master unlock password is ‘888888’.
4.7 USB & Multimedia The ZvSync device supports a rich set of features enabled through the use of a USB device. In order to support the PVR functions of time shifting and recording, a storage device (not provided) must be present. It is recommended that a high-performance USB storage device be used if these functions are to be utilized. The format must be FAT32. NTFS is not supported. Use of the PVR and media storage functions is freely available and encouraged.
5 Troubleshooting Problem Potential Reason Possible Action No picture Power is not connected Connect power supply Check wall source Switch on power to ZvSync The power is switched off Screen shows “No Signal” Cable feed is not connected Aerial cable is faulty Check/Connect power cable Check aerial and connections Correctly connect the audio cables No sound Incorrect or faulty from speaker connection with audio cable Sound on mute Only sound, no image on screen Incorrect A/V cable connection Progra
6 Technical Specifications Item Sub-Item Parameter Tuner Input Frequency 48-862MHz RF Input Level -20 to -82dBm IF Bandwidth 6,7, and 8MHz Modulation Aspect Ratio QPSK, 16QAM, 64QAM, 256QAM, DVB-T, DVB-T2 MPEG4 AVC/H.264 HP@l4 MPEG2 MP@ML/HL 480i, 480p, 576i, 576p, 720p, 1080i, 1080p60Hz 4:3, 16:9, Auto Output Port HDMI(v1.
7 Declaration of Conformity The Original Equipment Manufacturer herewith declares the conformity of the product with the following directives and standards: Low Voltage Directive 2006/95/EC EN 60065:2002+A1:2006 EMC Directive 2004/108/EC EN 55 013:2001+A1:2003+A2:2006 EN 55 020:2007 EN 61 000-3-2:2006 EN 61 000-3-3:2008 FCC, CE, C-Tick This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed of at the end of its life separately from normal hou
Contact ZeeVee Support For support, repairs, and warranty service contact the distributor where you purchased the product. For additional questions call +1(877) 4-ZEEVEE (1.877.493.3833) or e-mail support@zeevee.com. Representatives are available from 9:00 AM to 6:00 PM, Monday through Friday (Eastern Time). Sales North America: +1 (347) 851-7364 Phone sales@zeevee.com EMEA: +44 1494 956677 Phone EMEAsales@zeevee.com Pa g e 3 4 | Zv S y n c - EU U s e r ’s M a nual w ww. z eev ee.
Z v S y nc - E U Us er ’s Manual | P age 35
ZvSync-EU_70-00042-00_RevC