HDbridge 2312 CON FIG U RATI ON G U I D E SERIES EU
I N S T R U C T I O N S P E R TA I N I N G T O A R I S K O F F I R E , E L E C T R I C S H O C K , O R I N J U R Y T O P E R S O N S Important Safety Instructions. Save These Instructions. WARNING: When using electronic products, basic precautions should always be followed, including: 1. Keep these instructions. 9. Power cord must be accessible to allow for the removal of power from the unit. 2. Heed all warnings. 10.
Welcome to ZeeVee. Table of Contents ZeeVee products convert your video and audio source to Front and Back Panels . . . . . . . . . . . 4 a digital cable channel and broadcast it over coax to all Basic Installation. . . . . . . . . . . . . . . . 5 your HDTVs. This guide walks you through basic and more Tuning your channel at enhanced setup for ZeeVee’s HDbridge 2312 modulator. the HDTV (Auto Scan). . . . . . . . . . .
Front and Back Panels HDb2312 Name and description of unit Color Display Configuration and system status 5-Way Control Navigate options on front panel display Coax Output Two groups of up to 3 frequency-agile DVB-T/C RF CATV output channels for up to 12 video sources (2 groups of 3 channels is the default and recommended). Output power can be set between +45 to +25 dBmV using the Maestro web interface or the front panel.
Basic Installation Composite Video Source Analog Composite Audio Video Video Source RF Output +45 dBmV Back of HDb2312 Modulator Coax cable connects to coax network Ethernet to network or directly to computer WARNING: +45 dBmV Do not connect directly to HDTV Factory default settings allow HDb2312 series modulators to broadcast up to 12SD sources on RF channels 21, 22, 23, 24, 25, and 26 for reception at connected HDTVs. We recommend using the most updated version of firmware.
Front Panel Configuration Shows audio/video being encoded Green — Both audio and video are detected Yellow — Video, but no audio detected Red — No video detected You can set the RF broadcast channels using the front panel controls. In many cases, your ZeeVee modulator will require only these configurations. Setting the RF broadcast channels or power 1. Unlock the panel by pressing/holding together the left and right arrow buttons ( ) until “Setup” lights up. SETUP SCREEN 2.
CCIR Table vs Frequency Map RF Channel Band (MHz) RF Channel Band (MHz) RF Channel Band (MHz) 21 470-478 41 630-638 61 790-798 22 478-486 42 638-646 62 798-806 23 486-494 43 646-654 63 806-814 • RF Channel numbers are applied in threes based on the frequency map. For instance, if you enter RF Channel # “21” then RF Channel # “22” and “23” automatically populate.
Maestro Configuration Maestro is a configuration tool that you use optionally to customize your system beyond what is allowed in the front panel. For example, using Maestro you can assign a channel number (virtual channel) independent of the RF number and label the channels. Configuring RF numbers and logical channel numbers (LCN) 1. Click on the Channel Plan tab. Connecting with Maestro 1.
Using the Maestro tabs Delayed Audio Out found on the Channel Plan tab allows for matching audio to external audio system (first port only). Click on the Maestro tabs to configure your unit as needed. We provide brief information here. Please click on the Help button on each tab or refer to the Support section of our website for further detail on configuration options. Manage All allows you to view and configure all units on your network. THE RF TAB Allows you to change the RF power output.
Troubleshooting Unable to Connect to Maestro If unable to connect, try one of the following: If you are getting a page not found error when directly connected to a PC, try disabling WIFI. If that does not correct it, make sure your PC is not using a static IP address. The PC and the HDbridge2000 unit must be on the same IP subnet for them to communicate. For details on how to check for a static IP address, please see the FAQ section of our website.
5Ways to Register Year Warranty Mobile......... Click on the QR code with your mobile device’s code reader app Online......... Go to zeevee.com/register Email........... Send an email with all card info (below) to warranty@zeevee.com Mail............. Fill out the form, attach a stamp, and mail to ZeeVee Contact +1.877.493.3833 or warranty@zeevee.com with any questions. P age 11 BOSTON | DENVER | LONDON | support@zeevee.com +1.877.4ZEEVEE (1.877.493.
5Ways to Register Year Warranty Maestro...... Click on “ZeeVee Website” in the Support Tab when you begin your configuration Mobile......... Click on the QR code with your mobile device’s code reader app Online......... Go to zeevee.com/register Email........... Send an email with all card info (below) to warranty@zeevee.com Mail............. Fill out the form, attach a stamp, and mail to ZeeVee DECLARATION OF CONFORMITY Regulatory Product Number: Contact +1.877.493.3833 or warranty@zeevee.