Instruction Manual

Thank you for purchasing the Classic True Wireless Earbuds.
This manual provides more information about the wireless earbuds,
please read the instructions before using.
INSTRUCTION MANUAL
Pair the wireless earbuds with your mobile device
1. Keep the distance between the earbuds and mobile device within 32.8 feet.
2. De-activate the Bluetooth function on your mobile device.
3. Take both Earbuds out from Charing case and wait for 3 to 5 seconds for auto
pairing. The earbud has indicator blinking alternatively in Red and Blue.
One of the earbud will be blinking in Blue slowly when auto pairing is done
successfully on L/R earbuds..
4. Activate the Bluetooth function on your mobile device and select
“CLASSIC TWS” from the list shown.
5. After pairing is successful, both earbuds will start blinking slowly in blue.
*Attention: If the auto pairing is not successful, manual pairing between earbuds
is essential by following below procedures:
1. Make sure the earbuds are charged.
2. De-activate the Bluetooth function on your mobile device. (if you had been paired
the earbuds to some other mobile device(s) nearby, please sure to de-activate
those device(s) too).
3. Power on both earbuds simultaneously by pressing the touch control area for
3 seconds and wait for 3 to 5 seconds for auto pairing. (Keep the Bluetooth
function off on your mobile device before this operation.)
4. Activate the Bluetooth function on your mobile device and select “CLASSIC TWS”
from the list shown.
5. After pairing successfully, both earbuds will start blinking slowly in blue.
Reconnect the wireless earbuds to your mobile device
Disconnect the wireless earbuds from your mobile device
Switch off the Bluetooth on your mobile phone; or
Leave the earbuds 60 ft away from your mobile phone or further.
Answer / Reject a call
When receive a call, click touch control area once (on either earbud) to accept
the call, or answer the call normally via your mobile phone.
Touch and hold touch control area for 2 seconds to reject it.
End a call
To end the call, just click touch control area once at any side of earbud with
Beep sound to end it.
Functions
Pause / Play Music: Click touch control area once.
Skip to next track of music: Double click the touch control area.
Recharge Charging Case
1. Open the charging case cover.
2. Insert the Classic Earbuds into the charging case.
3. The earbuds will start to charge automatically or press the charging On/Off button.
4. LED indicator of the earbud will be turned to Red when charging
your earbuds.
5. Once fully charged, the LED will be off.
Charging your Earbuds
If the wireless earbuds cannot be paired with your device,
please try the following:
Ensure that your earbuds are in pairing mode or reconnection mode
Ensure that Bluetooth search function of your mobile device is activated.
If the wireless earbuds will not turn on:
Make sure the earbuds are fully charged.
Can I change the battery for the earbuds and the charging case?
The wireless earbuds and the charging case use a built-in non-detachable battery
which cannot be removed.
If the charging case cannot be recharged:
If you use a power outlet, ensure that the power supply is connected securely
and the outlet works. If you use a computer, ensure that it is connected and the
USB port is powered.
FAQ
Product Overview Power On/Off
Package Contents
-The input voltage to the product is 5V 1A.
-In order to charge the product in safe manner and reliable conditions, please
only adopt certified appropriate charger/ adapter for charging the product.
-Only charge the product at ambient temperatures between 10 deg °C/ 50 deg °F
and 40 deg °C/104 deg °F.
- Do not heat above 70 deg °C/158 deg °F, eg. Do not expose to sunlight or
throw into fire.
-Switch off the product after use.
-Please note that we won’t take any responsibility for any wrong operation (eg.
Voltage higher than 5V) as this may result in severe injury or loss of property, and
we cannot control the operating process during the time the user using this
product.
-In extreme cases, abuse or misuse of Lithium battery pack can lead to
explosion, heat generation, fire development or smoke development.
Safety instructions for the lithium battery and charging the product
4
5
6
1. Touch Control Area
2. LED Indicator / Built-in
Microphone
3. Magnetic Charging Port
4. Charging On / Off Button
5. LED Indicator
6. Micro USB Charging Port
USB Plug Micro USB Plug
Classic True Wireless Earbuds x 1 pair
Portable Charging Case x 1
Micro USB Charging Cable x 1
Instruction Manual x 1
Power On
Take out the earbuds from the charging case, it will automatic turn on and the
LED indicator will flash.
The Earbud can be power on manually by touch and hold the touch control area of
the earbud more than 3 seconds.
Power Off
Put back the earbuds into the charging case, it will automatic turn off.
The Earbuds will be power off by hold the control area more than 5 seconds.
The Earbuds will be power off automatically if no Bluetooth connection is made
within 3 minutes.
When powered on, the wireless earbuds will automatically connect with the last
successfully paired device.
Specifications
Driver Diameter: 10 mm
Impedance: 32 Ohms
Frequency Response: 20 Hz – 20K Hz
Sensitivity: 102 dB +/- 3 dB
Earbud Battery Capacity:
Li-ion 3.7V 40 mAh Per Earbud
Charging Case Battery Capacity:
Li-ion 3.7V 400 mAh
Bluetooth Range: 32.8 Feet
Playtime: 1.5 Hours Per Charge
Total Playtime: 7 Hours
(Earbuds playing time is 1.5 hours and
the Charging case can provide 4 times
for the earbuds charging.)
Charging Time: 4 Hours
Charging Method:
Magnetic Charging Case
Micro USB Charging Cable Included
Instruction Manual
Micro USB Charging Cable
Instruction
Manual
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
FCC ID: 2ADM5-EP-0635
Keep all relevant information for
future reference
Distributed by 1616 Holdings, Inc.
701 Market Street, Suite 200
Philadelphia, PA 19106
Made in China
ITEM# EP-0635
Earbuds Charging Case
Front Back
1
2
3
NOTE:
• You must select a qualified charger from a regular manufacturer.
• You must charge the charging case and earbuds if it has been not used for more than
12 months.
1. Use the Micro USB charging cable provided with the packaging.
2. Connect the Micro USB plug to Micro USB charging port on the charging case, then
connect the USB plug to a USB port on a computer or wall adapter to begin charging.
3. The Red LED on the charging case will be flashing during charge.
4. Once fully charged, the Red LED will be on.
For your safety, please always use appropriate 5V input charger/Adapter to charge the product.
DO NOT USE Quick Charging USB Adapter to charge the product, as it might damage the product.
CLASSIC
TRUE WIRELESS EARBUDS
DC5V / 1A