REVIEW ONLY 3/9/20 TC21 / TC26 Touch Computer Quick Start Guide MN-003892-01EN
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 Copyright ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2020 Zebra Technologies Corporation and/or its affiliates. All rights reserved. COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/copyright. WARRANTY: For complete warranty information, go to www.zebra.
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 Unpacking 1. Carefully remove all protective material from the device and save the shipping container for later storage and shipping. 2. Verify that the following were received: • Touch computer • PowerPrecision Lithium-ion battery • Regulatory Guide. 3. Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global Customer Support center immediately. 4.
REVIEW ONLY TC21/TC26 Quick Start Guide Table 1 3/9/20 Front View Features (continued) Number Item Function 5 Charging/Notification LED Indicates battery charging status while charging and application generated notifications. 6 Touch Screen Displays all information needed to operate the device. 7 Speaker Provides audio output for video and music playback. Provides audio in speakerphone mode.
REVIEW ONLY TC21/TC26 Quick Start Guide Table 2 3/9/20 Back View Features (continued) Number Item Function 15 Scan Button Initiates data capture (programmable). 16 Battery Release Latches Press to remove the battery. 17 Camera Flash Provides illumination for the camera. 18 Rear Camera Takes photos and videos. 19 Power Button Turns the display on and off. Press and hold to reset the device or power off. 20 Exit Window Provides data capture using the imager.
REVIEW ONLY TC21/TC26 Quick Start Guide 1. Lift the access door. Figure 3 Lift Access Door 2. Slide the microSD card holder to the unlock position. Figure 4 Unlock microSD Card Holder 3. Lift the microSD card holder.
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 4. Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door. Figure 6 Insert microSD Card in Holder 5. Close the microSD card holder and slide into the lock position. Figure 7 Re-install Access Door CAUTION: Access door must be replaced and securely seated to ensure proper device sealing. 6. Re-install the access door.
REVIEW ONLY TC21/TC26 Quick Start Guide 1. Remove access cover. Figure 9 Remove Access Door 2. Slide the SIM card holder to the unlock position. Figure 10 Unlock SIM Card Holder 3. Lift the SIM card holder door.
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 4. Place the nano SIM card into the card holder with contacts facing down. Figure 12 Place SIM Card in Holder 5. Close the SIM card holder door and slide into the lock position. Figure 13 Close SIM Card Holder Door CAUTION: Access door must be replaced and securely seated to ensure proper device sealing. 6. Re-install the access door.
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 1. Insert the battery, bottom first, into the battery compartment in the back of the device. Figure 15 Insert Bottom of Battery into Battery Compartment 2. Press the battery down into the battery compartment until the battery release latches snap into place.
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 Charging the Device CAUTION: Ensure that you follow the guidelines for battery safety described in the device Product Reference Guide. Use one of the following accessories to charge the device and/or spare battery. Table 3 Accessories Accessory Part Number Description 1-Slot Charge Only Cradle CRD-TC2Y-BS1CO-01 Provides communication and power to the device. Requires USB-C cable (CBL-TC5X-USBC2A-01) and power supply (PWR-WUA5V12W0xx).
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 Main Battery Charging To charge a device: 1. Insert the device into a slot to begin charging. 2. Ensure the device is seated properly. The device’s Charging/Notification LED indicates the status of the battery charging in the device. The 3,220 mAh (typical) standard battery charges from fully depleted to 90% in approximately 2.5 hours and from fully depleted to 100% in approximately three hours.
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 NOTE: In many cases the 90% charge provides plenty of charge for daily use. To achieve the best fast charging results use only Zebra charging accessories and batteries. Table 5 Spare Battery LED Charging Indicators LED Indication Solid Amber Spare battery is charging. Solid Green Spare battery charging is complete. Solid Red Spare battery is charging and battery is at the end of useful life. Charging complete and battery is at the end of useful life.
REVIEW ONLY TC21/TC26 Quick Start Guide Table 6 3/9/20 1-Slot Charge Only Cradle Features Number Item 1 Power Supply 2 USB-C Cable 3 USB-C Port 1-Slot USB/Ethernet Cradle Figure 17 1–Slot USB/Ethernet Cradle Setup 6 1 2 5 4 3 Table 7 1-Slot USB/Ethernet Cradle Features Number Item 1 Power Supply 2 DC Line Cord 3 USB-A Connector 4 USB micro-B Connector 5 USB micro-AB Port 6 AC Line Cord 23
REVIEW ONLY TC21/TC26 Quick Start Guide 4-Slot Charge Only Cradle with Battery Charger Figure 18 4-Slot Charge Only Cradle with Battery Charger 4 3 1 2 Table 8 4-Slot Charge Only Cradle with Battery Charger Features Number Item 1 Spare Battery Charging LED 2 Power LED 3 Spare Battery Slot 4 Device Charging Slot 24 3/9/20
REVIEW ONLY TC21/TC26 Quick Start Guide 5-Slot Charge Only Cradle Figure 19 5-Slot Charge Only Cradle 2 1 Table 9 5-Slot Charge Only Cradle Features Number Item 1 Power LED 2 Device Charging Slot 25 3/9/20
REVIEW ONLY TC21/TC26 Quick Start Guide 5-Slot Ethernet Cradle Figure 20 5-Slot Ethernet Cradle 3 2 1 Table 10 5-Slot Ethernet Cradle Features Number Item 1 100/100 LED 1 1000 LED 2 Device Charging Slot 26 3/9/20
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 4-Slot Battery Charger Figure 21 4-Slot Battery Charger 3 2 1 Table 11 4-Slot Battery Charger Features Number Item 1 Power LED 2 Battery Charging LED 3 Battery Slot USB cable The USB cable plugs into the bottom of the device. When attached to the device the cable allows charging, transferring data to a host computer, and connecting USB peripherals.
REVIEW ONLY TC21/TC26 Quick Start Guide Figure 22 3/9/20 USB cable Scanning with Internal Imager To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows the user to enable the imager, decode the barcode data, and display the barcode content. To scan with the internal imager: 1. Ensure that an app is open on the device and a text field is in focus (text cursor in text field). 2. Point the exit window on the top of the device at a barcode.
REVIEW ONLY TC21/TC26 Quick Start Guide 3/9/20 4. Ensure the barcode is within the area formed by the crosshairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions. Figure 24 Aiming Pattern Figure 25 Pick List Mode with Multiple Barcodes 5. The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded successfully. 6. Release the scan button. NOTE: Imager decoding usually occurs instantaneously.
REVIEW ONLY 3/9/20 www.zebra.