ET1 ENTERPRISE TABLET QUICK START GUIDE
Motorola reserves the right to make changes to any product to improve reliability, function, or design. Motorola does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
Features Decode LED Microphone Light Sensor Battery Charge LED Communication LED Front-facing Camera Touch Screen Programmable Buttons Back Button Home Button Menu Button 3
Features Secondary Microphone Camera Flash Rear-facing Camera USB Host Expansion Module Power Button Right Scan/Action Button Left Scan/Action Button Battery Charging LED Battery Release Latch Battery Speaker Speaker Headset Jack 4 I/O Connector HDMI Output Connector
Getting Started 3. Push the battery in until it snaps into place. To get started: Charge the Battery • Install the battery • Charge the battery Before using the ET1, charge the battery using one of the following accessories: • Start the ET1. • Single-slot USB Docking cradle • Four-slot Charge Only Docking cradle • USB/Charge cable and power supply. Install the Battery 1. Remove the battery from the packaging. 2.
Launch Applications Power Button To launch an application: Use the Power button to place the ET1 in suspend mode, battery swap mode, to reset the ET1 or to power off the ET1. 1. Touch the Launcher icon. The Launcher window displays. Launcher Suspend Mode Press and release the Power button to place the ET1 in suspend mode. In Suspend Mode the ET1 turns off the display and goes into a low power state to conserve battery power.
Hardware Reset Scan a Bar Code If the ET1 stop responding perform a hardware reset. Simultaneously press the Left Scan/Action, Right Scan/Action and Power buttons. Use the rear-facing camera to scan bar codes. Ensure that DataWedge is enabled and the cursor is in a text field. Lock the Screen Lock the screen to protect access to data. When locked, a Pattern, PIN or Password is required to unlock the ET1. Press the Power button to lock the screen. The ET1 also locks after a pre-defined time-out.
Photos and Videos To capture video: Use the rear-facing camera to take photos and capture video. NOTE A microSD card is required to save photos and videos. 1. Touch Launcher > Camera and then touch the video icon . 2. Point the ET1 at the subject. 3. On the screen, frame the subject in the window. 4. Touch the on-screen record button 5. Touch the on-screen stop button to begin recording. to end recording. View photos and videos using the Gallery application. To take a photo: 1.
Connect to a Bluetooth Device Connect to a WLAN Network To enable Bluetooth: To set up a WLAN network: 1. Touch 1. Touch > Settings > Wireless & networks. 2. Touch the Bluetooth checkbox. A green check appears in the checkbox and the Bluetooth icon appears in the Status bar indicating that Bluetooth is enabled. 3. Under Bluetooth settings, touch Scan for devices. The ET1 begins searching for discoverable Bluetooth devices in the area and lists them under Bluetooth devices. 4.
Battery Replacement To replace the battery: 1. Press and hold the Power button until the Device options menu displays. 2. Touch Battery Swap. The Scan LED lights red. 3. Wait until the Scan LED turns off. 4. Turn the ET1 over. 5. Press thumb against the side of the ET1 and battery. Using the index and middle fingers, move the battery release latch toward thumb and pull the battery out of the battery compartment. 6.
Accessories The following accessories are available for the ET1: • Single-slot Docking Cradle • Four-slot Charge Only Docking Cradle • Four-slot Battery Charger • USB/Charge Cable • Two-way DC Cable • Power supplies.
Motorola Solutions, Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2011 Motorola Solutions, Inc. All Rights Reserved.