AP8432_IG.
AP8432_IG.book Page 2 Monday, March 14, 2016 8:39 AM 2 AP-8432 Access Point Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. © 2016 Symbol Technologies, Inc.
AP8432_IG.book Page 3 Monday, March 14, 2016 8:39 AM Installation Guide 1.0 Introduction ............................................................................................. 5 1.1 Document Conventions ....................................................................... 5 1.2 Warnings ............................................................................................. 5 1.3 Site Preparation ................................................................................... 6 1.
AP8432_IG.book Page 4 Monday, March 14, 2016 8:39 AM 4 AP-8432 Access Point 5.3.1 Potentially Hazardous Atmospheres - Vehicle Installation ........ 36 5.3.2 Potentially Hazardous Atmospheres - Fixed Installations ......... 36 5.3.3 Safety in Aircraft ........................................................................ 36 5.3.4 Safety in Hospitals .................................................................... 36 5.4 RF Exposure Guidelines .........................................................
AP8432_IG.book Page 5 Monday, March 14, 2016 8:39 AM Installation Guide 5 1 Introduction Zebra AP-8432 internal antenna Access Point's are high-tier Access Points for dependable and efficient network performance. The Access Point’s unique WiNG 5 software enables the Access Point to function as either a Standalone Access Point, an Adaptive Access Point or a Virtual Controller.
AP8432_IG.book Page 6 Monday, March 14, 2016 8:39 AM 6 AP-8432 Access Point 1.3 Site Preparation • • • • • • 1.4 Consult your site survey and network analysis reports to determine specific equipment placement, power drops, and so on. Assign installation responsibility to the appropriate personnel. Identify and document where all installed components are located. Ensure adequate, dust-free ventilation to all installed equipment. Identify and prepare Ethernet and console port connections.
AP8432_IG.book Page 7 Monday, March 14, 2016 8:39 AM Installation Guide 1.5 7 AP-8432 Antennas 1.5.1 Dual Band 2.4 GHz / 5 GHz Internal - US An AP-8432 internal antenna Access Point supports the following dual band antenna: Antenna Type Monopole 2.4 GHZ Gain (dBi) Bluetooth: 7.7 Radio 2: 4.4 5 GHZ Gain (dBi) Radio 1: 6.8 Radio 2: 5.9 Elevation Gain (dBi) Radio 1: 3.4 Radio 2: 4.
AP8432_IG.book Page 8 Monday, March 14, 2016 8:39 AM 8 AP-8432 Access Point 2 Hardware Installation 2.1 Installation Instructions An AP-8432 Access Point mounts either on a wall (with M 3.5 x 0.6 x 23 MM pan head screws and mounting bracket or equivalent) or on a suspended ceiling T-bar. To prepare for the installation: 1. Match the part number on the purchase order with the part numbers in the packing list and on the case of the Access Point. 2.
AP8432_IG.book Page 9 Monday, March 14, 2016 8:39 AM Installation Guide 2.2 9 Precautions Before installing an AP-8432 Access Point, verify the following: • • • 2.3 Your are using the correctly rated power solution for the AP-8432 (either the AP-PSBIAS-2P3-ATR Power Injector or the PWR-BGA48V45W0WW external power supply) Do not to install the AP-8432 in wet or dusty areas. Verify the environment has a continuous temperature range between 32° F to 104° or 0° C to 50° C.
AP8432_IG.book Page 10 Monday, March 14, 2016 8:39 AM 10 AP-8432 Access Point Caution • Using a non-compliant injector, or an injector supporting legacy modes prohibits the AP-8533 from functioning optimally. Caution • Do not plug the AP-PSBIAS-2P3-ATR Power Injector into the Access Point’s Console port. Connecting the Power Injector into the console port can damage the port and void the Access Point’s product warranty. The AP-8432’s supported Power Injector (Part No.
AP8432_IG.book Page 11 Monday, March 14, 2016 8:39 AM Installation Guide 11 A separate Power Injector is required for each AP-8432 Access Point comprising the network. The Power Injector can be installed free standing, on an even horizontal surface or wall mounted using the Power Injector’s wall mounting key holes. The following guidelines should be carefully followed before cabling the Power Injector to an Ethernet source and an Access Point: • • Do not block or cover airflow to the Power Injector.
AP8432_IG.book Page 12 Monday, March 14, 2016 8:39 AM 12 AP-8432 Access Point • The Power Injector isn’t a repeater, and does not amplify the Ethernet signal. For optimal performance, ensure the Power Injector is placed as close as possible to the data port. CAUTION To avoid problematic performance and restarts, disable POE from a wired switch port connected to an Access Point if mid-span power sourcing equipment (PSE) is used between the two, regardless of the manufacturer of the switch.
AP8432_IG.book Page 13 Monday, March 14, 2016 8:39 AM Installation Guide 2.5.1 13 Wall Mount Procedure - New Installation This section describes a new AP-8432 installation with no previous Access Point existing on the intended wall surface. 1. Place the mounting bracket against the wall. 2. Mark the screw hole locations depending on the intended deployment orientation of the unit. Note • When pre-drilling a hole the recommended hole size is 4mm (0.16in.). 3.
AP8432_IG.book Page 14 Monday, March 14, 2016 8:39 AM 14 AP-8432 Access Point For Power Injector installations: a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the Power Injector Data & Power Out connector and the Access Point’s GE1/POE port. b. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the Power Injector Data In connector. c.
AP8432_IG.book Page 15 Monday, March 14, 2016 8:39 AM Installation Guide 2.6 15 Suspended Ceiling T-Bar Mount Instructions Ceiling mount requires holding the AP-8432 up against the T-bar of a suspended ceiling grid and twisting the unit on to the T-bar. If deploying the AP-8432 on a sculpted ceiling T-Bar, the Access Point mounting kit (Part No. KT-135628-01) can optionally be used as well. 1.
AP8432_IG.book Page 16 Monday, March 14, 2016 8:39 AM 16 AP-8432 Access Point For standard power adapter (non Power Injector) and line cord installations: a. Connect a RJ-45 Ethernet cable between the network data supply (host) and the Access Point’s GE1/POE port. b. Verify the power adapter is correctly rated according the country of operation. c. Connect the power supply line cord to the power adapter. d. Attach the power adapter cable into the power connector on the Access Point. e.
AP8432_IG.book Page 17 Monday, March 14, 2016 8:39 AM Installation Guide 17 8. Rotate the Access Point chassis 45 degrees counter-clockwise. The clips click as they fasten to the T-bar. The Access Point is ready to configure.
AP8432_IG.book Page 18 Monday, March 14, 2016 8:39 AM 18 AP-8432 Access Point 2.7 LED Indicators The AP-8432 LED activity indicators are located on the top of the housing and are visible through the enclosure. The LEDs display error conditions, and transmission, and network activity for the 5 GHz 802.11ac (amber) radio and the 2.4 GHz 802.11n (green) radio, sensor radio (white) and the BLE radio (blue). State 5 GHz Activity LED (Amber) 2.
AP8432_IG.book Page 19 Monday, March 14, 2016 8:39 AM Installation Guide State 19 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green) LED (Blue) LED (White) Not configured On On N/A N/A Locate AP Mode LEDs blink in an alternating green, amber, blue and white pattern using an irregular blink rate. This LED state in no way resembles normal operating conditions LEDs blink in an alternating green, amber, blue and white pattern using an irregular blink rate.
AP8432_IG.book Page 20 Monday, March 14, 2016 8:39 AM 20 AP-8432 Access Point 3 Basic Access Point Configuration Once the AP-8432 is installed and powered on, complete the following steps to get the Access Point up and running and access management functions: 1. The Access Point’s IP address is optimally provided using DHCP. A zero config IP address can also be derived if DHCP resources are unavailable.
AP8432_IG.book Page 21 Monday, March 14, 2016 8:39 AM Installation Guide 21 5. Click the Login button to load the management interface. Note • When logging in for the first time, you’re prompted to change the password to enhance device security in subsequent logins. Note • If you get disconnected when running the wizard, you can connect again with the Access Point’s actual IP address (once obtained) and resume the wizard.
AP8432_IG.book Page 22 Monday, March 14, 2016 8:39 AM 22 AP-8432 Access Point Note • The Initial Setup Wizard displays the same pages and content for each Access Point type supported. The only difference being the number of radios configurable by Access Point, as models vary. The Introduction screen displays the various actions that can be performed using the wizard under the Function Highlight field. Use the Choose One type to Setup the Access Point field options to select the type of wizard to run.
AP8432_IG.book Page 23 Monday, March 14, 2016 8:39 AM Installation Guide 23 A green checkmark to the left of an item in the Navigation Panel defines the task as having its minimum required configuration set correctly. A red X defines a task as still requiring at least one parameter be defined correctly. 6. Select Save/Commit within each page to save the updates made to that page's configuration. Select Next to proceed to the next page listed in the Navigation Panel without saving your updates.
AP8432_IG.book Page 24 Monday, March 14, 2016 8:39 AM 24 AP-8432 Access Point Note • The professional installer should refer to the WiNG Access Point System Reference Guide available at www.zebra.com/support for detailed information on how to set the Access Point’s transmit power, antenna gain and channel in respect to the deployment country’s unique regulatory requirements. 9.
AP8432_IG.book Page 25 Monday, March 14, 2016 8:39 AM Installation Guide 25 12. The Typical Setup Wizard displays the Network Topology screen to define how the Access Point manages network traffic. 13. Select an Access Point Mode from the available options. • Router Mode - In Router Mode, the Access Point routes traffic between the local network (LAN) and the Internet or external network (WAN). Router mode is recommended in a deployment supported by just a single Access Point.
AP8432_IG.book Page 26 Monday, March 14, 2016 8:39 AM 26 AP-8432 Access Point 2.4GHz and 5GHz radio bands. Note • When Bridge Mode is selected, WAN configuration cannot be performed and the Typical Setup Wizard does not display the WAN configuration screen. 14. Select Next. The Typical Setup Wizard displays the LAN Configuration screen to set the Access Point's LAN interface configuration. 15.
AP8432_IG.book Page 27 Monday, March 14, 2016 8:39 AM Installation Guide 27 fields will become enabled on the bottom portion of the screen. • Use on-board DHCP server to assign IP addresses to wireless clients - Select the checkbox to enable the Access Point’s DHCP server to provide IP and DNS information to requesting clients on the LAN interface. • Range - Enter a starting and ending IP Address range for client assignments on the LAN interface. Avoid assigning IP addresses from x.x.x.1 - x.x.x.
AP8432_IG.book Page 28 Monday, March 14, 2016 8:39 AM 28 AP-8432 Access Point 17. Set the following WLAN1 Configuration parameters: • SSID - Configure the SSID for the WLAN. • WLAN Type - Configure encryption and authentication settings to protect the data and user integrity of WLAN 1. • No Authentication and No Encryption - Configures a network without any user authentication or data encryption. This means any data transmitted through the network is in plain text.
AP8432_IG.book Page 29 Monday, March 14, 2016 8:39 AM Installation Guide 19. Use the Radius Server Configuration screen to configure the users for the onboard RADIUS server. Use the screen to add, modify and remove RADIUS users. 20. Select Add User to display the dialog to enter user information to add to the RADIUS server user database.
AP8432_IG.book Page 30 Monday, March 14, 2016 8:39 AM 30 AP-8432 Access Point 21. Enter the following user information: • Username - Provide a user name to authenticate the user. • Password - Provide a password to authenticate the user. • Confirm Password - Confirm the password by entering the same password entered in the Password field. • Description - Provide a description to identify the user created in the RADIUS server database. 22.
AP8432_IG.book Page 31 Monday, March 14, 2016 8:39 AM Installation Guide 31 26. Select Next. The Typical Setup Wizard displays the Summary and Commit screen to summarize the screens (pages) and settings updated using the Typical Setup Wizard. No user intervention or additional settings are required. Its an additional means of validating the Access Point’s updated configuration before it’s deployed.
AP8432_IG.book Page 32 Monday, March 14, 2016 8:39 AM 32 AP-8432 Access Point 4 AP-8432 Access Point Specifications 4.1 Electrical Characteristics An AP-8432 Access Point has the following electrical characteristics: Operating Current 48VDC, 0.625A (AUX input voltage) & Voltage 48VDC PWR-BGA48V45W0WW Power Supply 48VDC, 0.53A (POE) 802.3at AP-PSBIAS-2P3-ATR Power Injector 4.2 Physical Characteristics An AP-8432 Access Point has the following physical characteristics: Dimensions 8.25 in. L x 8.25 in.
AP8432_IG.book Page 33 Monday, March 14, 2016 8:39 AM Installation Guide 4.3 33 Radio Characteristics The AP-8432 Access Point has the following radio characteristics: Data Rates Supported 802.11b/g: 1,2,5.5,11,6,9,12,18,24,36,48 and 54 Mbps 802.11a: 6,9,12,18,24,36,48, and 54 Mbps 802.11n: MCS 0-31 up to 600Mbps 802.11ac: MCS 0-9 up to 1.
AP8432_IG.book Page 34 Monday, March 14, 2016 8:39 AM 34 AP-8432 Access Point 5 Regulatory Information 5.1 Regulatory Information This guide applies to the following Model Numbers: AP-8432I. All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translations are available at the following Website: www.zebra.
AP8432_IG.book Page 35 Monday, March 14, 2016 8:39 AM Installation Guide 5.2 35 Wireless Device Country Approvals Note: This section is only applicable to WW/WR/EU configurations. Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use in the following countries and continents: United States, Canada, Japan, China, South Korea, Australia, and Europe. Please refer to the Declaration of Conformity (DoC) for details of other country markings.
AP8432_IG.book Page 36 Monday, March 14, 2016 8:39 AM 36 AP-8432 Access Point Avertissement: Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.
AP8432_IG.book Page 37 Monday, March 14, 2016 8:39 AM Installation Guide 37 Wireless devices transmit radio frequency energy and may affect medical electrical equipment. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, or healthcare facilities. These requests are designed to prevent possible interference with sensitive medical equipment. Wireless devices transmit radio frequency energy and may affect medical electrical equipment.
AP8432_IG.book Page 38 Monday, March 14, 2016 8:39 AM 38 AP-8432 Access Point 5.4.2 International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on “International” human exposure to electromagnetic fields refer to the Declaration of Conformity (DoC) at www.zebra.com/doc. 5.4.
AP8432_IG.book Page 39 Monday, March 14, 2016 8:39 AM Installation Guide 39 Remote and Standalone Antenna Configurations To comply with FCC RF exposure requirements, Antennas that are mounted externally must be professionally installed at a fixed location and operate with a minimum distance of 40cm from all persons. To comply with FCC Antenna requirements, the Antenna must be adjusted such that the RF emission lobes are below 30 degrees elevation. 5.
AP8432_IG.book Page 40 Monday, March 14, 2016 8:39 AM 40 AP-8432 Access Point 5.6.1 Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 5.6.
AP8432_IG.book Page 41 Monday, March 14, 2016 8:39 AM Installation Guide 41 puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante. In compliance with respective local regulatory law, AP software provides professional installers the option to configure the antenna type and antenna gain for approved antennas.
AP8432_IG.book Page 42 Monday, March 14, 2016 8:39 AM 42 AP-8432 Access Point 5.9 Japan (VCCI) - Voluntary Control Council for Interference Class B ITE 5.10 Korea Warning Statement for Class B ITE 5.11 Other Countries All 2.4GHz and 5GHz Wireless Devices: Australia Use of 5GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65GHz. Brazil (UNWANTED EMISSIONS - ALL PRODUCTS) Regulatory declarations for AP-8432 - BRAZIL For more information consult the website www.anatel.gov.br.
AP8432_IG.book Page 43 Monday, March 14, 2016 8:39 AM Installation Guide Este dispositivo está em conformidade com as diretrizes de exposição à radiofrequência quando posicionado pelo menos 25 centímetros de distância do corpo. Para maiores informações, consulte o site da Anatel. Chile Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas. China Hong Kong In accordance with HKTA1039, the band 5.15GHz - 5.
AP8432_IG.book Page 44 Monday, March 14, 2016 8:39 AM 44 AP-8432 Access Point Taiwan 在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用 Turkey Bu cihaz Türkçe karakterlerin tamam?n? ihtiva eden ETSI TS 123.038 V8.0.0 (veya sonraki sürümün kodu) ve ETSI TS 123.040 V8.1.0 (veya sonraki sürümün kodu) teknik özelliklerine uygundur. Ukraine Дане обладнання відповідає вимогам технічного регламенту №1057, № 2008 на обмеження щодо використання деяких небезпечних речовин в електричних та електронних пристроях.
AP8432_IG.book Page 45 Monday, March 14, 2016 8:39 AM Installation Guide 5.12 Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee. Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage.
AP8432_IG.book Page 46 Monday, March 14, 2016 8:39 AM 46 AP-8432 Access Point Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: www.zebra.com/weee. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση www.zebra.
AP8432_IG.book Page 47 Monday, March 14, 2016 8:39 AM Installation Guide 6 Support If you have a problem with your equipment, contact support for your region. Contact information is available at: www.zebra.com/support When contacting support, please provide the following information: • Serial number of the unit • Model number or product name • Software type and version number Support responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements.
AP8432_IG.book Page 48 Monday, March 14, 2016 8:39 AM 48 AP-8432 Access Point 7 Zebra Technologies Inc. End-User Software License Agreement BY INSTALLING AND/OR USING THIS PRODUCT, YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND ITS TERMS. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, ZEBRA IS NOT WILLING TO LICENSE THE PRODUCT TO YOU, AND YOU MUST NOT INSTALL OR USE THIS PRODUCT.
AP8432_IG.book Page 49 Monday, March 14, 2016 8:39 AM Installation Guide 49 Portions of the Products are protected by United States patent and copyright laws, international treaty provisions, and other applicable laws. Therefore, you must treat the Products like any other copyrighted material (e.g., a book or musical recording) except that you may make one copy of the Product solely for back-up purposes.
AP8432_IG.book Page 50 Monday, March 14, 2016 8:39 AM 50 AP-8432 Access Point BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some jurisdictions do not permit limitations of liability for incidental or consequential damages, so the above exclusions may not apply to you. This Limitation of Liability provision survives the termination of this Agreement and applies notwithstanding any contrary provision in this Agreement.
AP8432_IG.book Page 51 Monday, March 14, 2016 8:39 AM Installation Guide 51 Assignment Except as otherwise provided in this section, neither party may assign this Agreement, or any of its rights or obligations under this Agreement, without the prior written approval of the other party, which will not be unreasonably withheld. Any attempted assignment, delegation, or transfer without the necessary approval will be void.
AP8432_IG.book Page 52 Monday, March 14, 2016 8:39 AM 52 AP-8432 Access Point Third Party Software The Products may contain one or more items of Third-Party Software. The terms of this Agreement govern your use of any Third-Party Software UNLESS A SEPARATE THIRD-PARTY SOFTWARE LICENSE IS INCLUDED, IN WHICH CASE YOUR USE OF THE THIRD-PARTY SOFTWARE WILL THEN BE GOVERNED BY THE SEPARATE THIRD-PARTY LICENSE. Open Source Software The Products may contain one or more items of Open Source Software.
AP8432_IG.
AP8432_IG.
AP8432_IG.
AP8432_IG.
AP8432_IG.book Page 55 Monday, March 14, 2016 8:39 AM Zebra Technologies Corporation Lincolnshire, IL 60069 USA Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc. a Zebra Technologies company. © 2016 Symbol Technologies, Inc.
AP8432_IG.
