WA9903 - RFID MODULE UHF CIRCULAR (NA) POD H/W INSTALLATION SHEET Important: All Approval and safety information is outlined in the ‘WORKABOUTPRO4 Regulatory & Warranty Guide – part number 8000296 provided with each WORKABOUTPRO4. Warning: The WORKABOUTPRO4 with the RFID option must not be held closer than 20 cm from the rest of the body. This product must not be used in a holster or on a belt-clip. RFID cannot be used in co-transmission with WAN module. © 2014 Motorola Solutions, Inc.
1. Product Description Easily installable expansion modules for the WORKABOUT PRO4 allow you to customise this hand-held to meet your specific mobile computing requirements. This chapter outlines how to install the AMERICAN UHF CIRCULAR RFID Module. The RFID MODULE UHF CIRCULAR (WA9903) kit is based on the Sailfish UHF module from MOTOROLA Inc. (Model: 21-121559).
2. Product Installation Before installing a module in the WORKABOUT PRO4, all power sources must be turned off. Remove the battery. If your unit is using AC power, disconnect it. Figure 2-1 Battery location With the power shut down, you can now install the AMERICAN RFID Module UHF CIRCULAR. Remove the existing endcap and pod or backplate Figure 2-2 WAP4 Disassembled © 2014 Motorola Solutions, Inc. All Rights Reserved.
Slide the RFID Module inside the back opening Figure 2-3 RFID Module Assembly Drive the 4 screws that fix the RFID module on WAP4 frame Figure 2-4 RFID Module Assembly © 2014 Motorola Solutions, Inc. All Rights Reserved. March 20, 2014 8073681 C MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners..
Stick EMI Gaskets on the RFID module as shown hereafter: Plug the 2 U.FL antenna connectors to the Sailfish module. Warning: Make sure you use the proper RF port Connect UFL connector with white rubber on the right port. Figure 2-5 CIRCULAR ANTENNA Assembly © 2014 Motorola Solutions, Inc. All Rights Reserved. March 20, 2014 8073681 C MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.
Reassemble the pod antenna and the endcap Figure 2-6 Final Assembly IF the model number of WorkAbout Pro4 is 7528XUHFN (WLAN only) put this label: Figure 2-7 FCC/IC Label for WLAN only variant © 2014 Motorola Solutions, Inc. All Rights Reserved. March 20, 2014 8073681 C MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners..
IF the model number of WorkAbout Pro4 is 7528XPUHFN (WWAN version) put this label type: Figure 2-8 FCC/IC Label for WWAN variant Stick the label in the location following depending on WorkAbout Pro4 variant: Figure 2-9 WorkAbout Pro4 Long Alphanumeric Keyboard Figure 2-10 WorkAbout Pro4 Short Numeric Keyboard © 2014 Motorola Solutions, Inc. All Rights Reserved.
3. Software installation: To get current driver for WorkAbout Pro4, go to the website at: http://community.psion.com/downloads/developer_sdkhdk/m/rfid_sdk/ Copy and install the latest CAB file named “WAP4_WM_RFID_UHF”. Figure 3-1 Driver CAB file Figure 3-2 Driver sucFCC/ICssfully Installed After installation, select RFID Demo in the Start menu to start the RFID sample application. Figure 3-3 RFID demo Icon Figure 3-4 RFID Sample Application Window © 2014 Motorola Solutions, Inc.
To read the ID of TAG, press the Start Reading button ID Button. Put the TAG in front of the antenna. Tap Stop Reading to end tag reading. Figure 3-5 ID Tag Reading For detailed instructions on how to use the RFID demo application, please visit http://www.motorolasolutions.com and download ‘RFID Demo Applications User Guide (P/N 72E160038-01)’ Reading area: This area depends on the TAG type, TAG packaging, Tag position and environment (metallic or not).
RFID MODULE UHF CIRCULAR (FCC/IC) ENDCAP RFID Regulatory information IMPORTANT NOTE FOR NORTH AMERICA: The RFID must not be used whilst the host WORKABOUTPRO4 is being powered by the ac/dc adaptor. FCC Information to Users: Radiation Exposure Compliance This product complies with the FCC RF exposure limits for an uncontrolled environment. For continued compliance, the product must not be held closer than 20 cm from the rest of the body. This product must not be used in a holster or on a belt-clip.
Emissions Information for Canada: This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada license-exempt RSS standard(s).