User's Manual

2GIG-XCVR2e
Transceiver
Module
PRODUCT DESCRIPTION
The Model 2GIG-XCVR2e Transceiver Module is designed to
be used with the 2GIG security system control panel. The
transceiver is a dual frequency device. It receives 345MHz
signals from the system sensors, and receives and transmits
900MHz signals to and from the Model 2GIG-TS1 Wireless
Keypad.
To use a Model 2GIG-TS1 Wireless Keypad with the 2GIG
GC2e security system control panel, the 2GIG-XCVR2e
Transceiver Module must be installed into the control panel.
The control panel must also be running rmware
Version1.23 or greater to function with the transceiver
and wireless keypad. Check the current version number of
the rmware using the control panel’s toolbox feature.
If the control panel needs a rmware update, contact 2GIG for
details on obtaining a compatible control panel or to receive
an over-the-air update through the control panel’s cell radio (if
the panel is cell radio equipped).
COMPONENT LOCATIONS REMOVE POWER
REMOVE EXISTING RECEIVER TRANSCEIVER INTO 3-PIN CONNECTOR TRANSCEIVER INTO 5-PIN CONNECTOR ANTENNA PLACEMENT
RECONNECT BATTERY TEST SYSTEM LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against
defects in material and workmanship for two (2) years. This warranty
extends only to wholesale customers who buy direct from Nortek
Security & Control LLC or through Nortek Security & Control LLC’s
normal distribution channels. Nortek Security & Control LLC does not
warrant this product to consumers. Consumers should inquire from
their selling dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of Nortek Security &
Control LLC for consequential damages arising out of or in connection
with use or performance of this product or other indirect damages
with respect to loss of property, revenue, or prot, or cost of removal,
installation, or reinstallation. All implied warranties for functionality, are
valid only until the warranty expires. This Nortek Security & Control LLC
Warranty is in lieu of all other warranties expressed or implied.
FCC/IC STATEMENTS
RF Exposure Considerations
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
RF Exposure - This device is only authorized for use in a mobile application. At
least 20 cm of separation distance between the module and the user’s body must
be maintained at all times.
A label must be afxed to the outside of nal commercial product with the following
statements:
This device contains FCC ID: EF400209
This device contains IC ID: 1078A-00209
Consistent with §2.909(a), the following text must be included within the user’s
manual or operator instruction guide for the nal commercial product.
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device is only authorized for use in a mobile application. At least 20 cm of
separation distance between the module and the user’s body must be maintained
at all times.
The nal host/module combination may also need to be evaluated against the FCC
Part 15B criteria for unintentional radiators in order to be properly authorized for
operation as a Part 15 digital device. The FCC Part 15 Statement shall be included
in the user manual of nal commercial product if applicable.
CAUTION: Any changes or modications not expressly approved could void the
user’s authority to operate the equipment.
or dial
PRINTER’S INSTRUCTIONS:
INSTR,XCVR2e,2GIG - LINEAR P/N: 10029741 Rev-B X1 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 1 OF 2
900 MHZ
ANTENNAA
PLUG-IN
TRANSCEIVERR
MODULE
FOAM PRESSURE PAD
SHIELD
THE ANTENNA PLACEMENT IS CRITICAL
FOR PROPER OPERATIONN
DO NOT BEND THE ANTENNA !!!
IMPORTANT !!!
BEFORE PROCEEDING, UN-PLUG THE AC POWER
SUPPLY, OPEN THE CONTROL PANEL CASE, THEN
DISCONNECT THE BACKUP BATTERY
PULL UP ON THE PLUG-IN RECEIVER MODULE TO
5-PIN
CONNECTOR
3-PIN
CONNECTOR
DISCONNECT IT FROM THE 5-PIN AND 3-PIN CONNECTORS
CONTROL
PANEL
THE PLUG-IN RECEIVER MODULE IS
LOCATED ON THE MAIN CIRCUIT BOARD,
RIGHT BEHIND THE HOME BUTTON
RECEIVER
MODULE
RE-CONNECT THE BATTERY, CLOSE THE CONTROL
PANEL, THEN PLUG IN THE AC POWER SUPPLY
PLACE THE CONSOLE IN
PROGRAMMING MODE
TO PREPARE IT FOR ENROLLING
THE WIRELESS KEYPAD
REFER TO THE CONSOLE'S
INSTALLATION INSTRUCTIONS
FOR DETAILS ON PROGRAMMING
AND TESTING THE WIRELESS KEYPAD.
2GIG GC2e CONSOLE
TS1 WIRELESS KEYPAD
USE THE CONTROL PANEL'S TOOLBOX TO CHECK THE
FIRMWARE VERSION IN THE CONTROL PANEL. THE FIRMWARE
VERSION MUST BE 1.23 OR GREATER BEFORE PROCEEDING.
WHEN
LEARN
IS PRESSED ON
THE CONSOLE, AND
PAIR WITH PANEL
IS PRESSED ON THE TS1, THE TWO
UNITS WILL COMMUNICATE AND
AUTOMATICALLY ENROLL THE KEYPAD.
INSERT THE TRANSCEIVER PARTWAY
INTO THE 3-PIN CONNECTOR
BE CAREFUL TO ALIGN ALL THE
PINS INTO THE CONNECTOR.
INSERT THE TRANSCEIVER
INTO THE 5-PIN CONNECTOR
BE CAREFUL TO
ALIGN ALL THE PINS
INTO THE CONNECTOR !!!
PRESS DOWN ON
FOAM PRESSURE PAD
TO SEAT THE XCVR2
1
2
THE ANTENNA PLACEMENT IS
CRITICAL FOR PROPER OPERATION
DO NOT BEND THE ANTENNA!
THE ANTENNA SHOULD BE
AT THIS ANGLE AFTER
TRANSCEIVER INSTALLATION
Only compatible with the GC2e panel.
Installation
Instructions
Compatible Devices
• eSeries 345 sensors
• Legacy 345 sensors
• 2GIG-TS1
• Image Sensor 1 & 2
WARNING: Cancer-
www.P65Warnings.ca.gov