FCC Part 22 Transmitter Certification Test Report FCC ID: SO4YX500-CEL FCC Rule Part: CFR 47 Part 22 Subpart H ACS Report Number: 05-0343-22H Manufacturer: Wireless Extenders Equipment Type: Cellular Band Bi-Directional Booster Model: YX500-CEL Installation Guide 5015 B.U.
YX500-CEL Installation Guide Rev.
Copyright Notice This manual is copyrighted. All rights reserved. This manual, whole or in part, may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form for distribution. This manual, whole or in part, may not be modified without prior consent, in writing, from Wireless Extenders. Copyright © 2005 by Wireless Extenders, Inc. 330 Research Court Suite 250, Norcross, GA 30092, U.S.A.
Read First Before Installing the YX500-CEL YX500-CEL For Cell Phones Operating on Cellular 800MHZ Frequencies Only Before unpacking this box, verify that your phone operates on Cellular 800MHz frequencies. The YX500-CEL will enhance your in-building coverage for local provider networks operating at the 800MHz (Cellular) frequency. To verify that your phone uses Cellular 800MHz frequencies, please follow these four simple steps: 1) Unpack the Base Unit and the Base Unit power supply only.
Safety and Product Warranty Information Safety Guidelines Please adhere to the following safety guidelines during the installation of the YX500-CEL. 1) In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element (antenna) shall be installed such that a minimum separation distance of 8 inches (20cm) is maintained between the radiating element and the user and/or general population.
Outdoor Installation of the Signal Antenna Grounding the Signal Antenna If you decide to install the Signal Antenna outdoors, it must be properly grounded. This will help protect your property against lightning strikes during a lightning storm. The installation must be in accordance with Article 810 of the National Electric Code (NEC). A listed antenna discharge unit must be provided for the lead-in coaxial cable per NEC article 8.10.
This Page Intentionally Left Blank iv Wireless Extenders YX500-CEL Installation Guide
Table of Contents Read First Before Installing the YX500-CEL................................................................. i YX500-CEL For Cell Phones Operating on Cellular 800MHZ Frequencies Only.................i Safety and Product Warranty Information................................................................... ii Safety Guidelines ..................................................................................................................ii Limited Liability ..............................
This Page Intentionally Left Blank vi Wireless Extenders YX500-CEL Installation Guide
Package Contents Before you begin, make sure all of the following parts came with your kit: Item Quantity Part # Description 1 1 DMAN-0009 Before Unpacking Sheet 2 1 DMAN-0008 Installation Overview Poster 3 1 DMAN-0010 YX500-CEL Installation Guide 4 1 APRD-0003 YX500-CEL Base Unit 5 1 CPSP-0001 YX500 - Base Unit Power Supply 6 4 CHDW-0007 YX500 - Base Unit rubber feet 7 1 FHSG-0004 YX500 - Base Unit Bracket 8 1 CANT-0010 0dBi YX500-CEL Base Unit Antenna 9 1 CANT-0009
Accessories - Improve your coverage The following accessories are also available to improve signal reception and provide increased coverage in your home or office or improve installation. To order, call 1-800-871-1612 or visit, www.WirelessExtenders.com.
YX500-CEL Product Overview Overview Thank you for selecting the Wireless Extenders YX500-CEL. With the YX500CEL, you will now be able to use your cell phone INSIDE your home or office. Gone are the days when you have to go to the window upstairs or walk outside to get enough signal. Like a skylight that brings sunlight into your home, the YX500-CEL transports and amplifies the outdoor cellular, 800MHz, signals into your home or office.
Preparing to Install the YX500-CEL Check Signal Availability Before installing the YX500-CEL in your home, make sure that you can place calls on the outside of your home or in the attic. The YX500-CEL can only bring cell phone signals into your home if cell phone signals are reaching the outside of your home or your attic. Go outside or into your attic with your cell phone and do the following: 1) Make a call to confirm that a strong enough signal is reaching your home.
Determine the Needed Coverage Area Identify the location in your home/office where you need signal coverage the most. The YX500-CEL can cover approximately 2500 square feet (coverage varies based on outdoor signal level, building construction, and general installation care). Walls, ceilings or floors will reduce the coverage area.
Warning: Installation Tools The YX500-CEL base unit MUST only be used with the provided power adaptor. Attempts to use other power adaptors will void the warranty and is not FCC approved. The following tools are needed to install the YX500-CEL: • #2 Philips screwdriver • Cordless drill • Cellular phone operating in 800 MHz band Installing the YX500-CEL Installing the Signal Antenna There are four options available for installing the Signal Antenna: 1.
Figure 4 – Signal Antenna and Mounting Bracket Signal Antenna Mounting to an Attic Cross Beam 1) Identify the wood beam where you will attach the mounting bracket and drill two holes. For the signal reception, install the Signal Antenna at the highest possible point in your attic. Avoid placing the antenna within 3 feet (1 meter) of metal objects (pipes, metal siding, A/C unit, etc.
Figure 6 - Attach Mounting Bracket 3) Mount the Signal Antenna to the mounting bracket, making sure that the antenna is perpendicular to the floor before securing it to the bracket. Figure 7 - Secure Signal Antenna to bracket Note: If you need to adjust the Signal Antenna after securing it to the bracket, insert a small flat-head screwdriver on each side of the bracket bridge. Pushing down on the bridge grips will allow you to slide the bridge off each tab.
Figure 8 - Attach Coaxial Cable to Antenna Signal Antenna Mounting to an Attic Top or Main Beam If a cross-beam is not available, the antenna bracket can be mounted to a main beam. Secure the bracket near the top of the Signal Antenna instead of near the base. Figure 9 - Mounting Signal Antenna to a Main Beam Running the Coaxial Cable to the Base Unit After installing the Signal Antenna and connecting the coaxial cable, run it to the location in your home where you plan to install the Base Unit.
Additional Cable Requirements If the distance between the Signal Antenna and the Base Unit exceeds 35 feet, you will need to purchase additional coaxial cable. You must use RG-6 coaxial cable and connectors, which are rated for Outdoor Satellite TV use and can be found at many home improvement and electronic stores. For the best performance, purchase Wireless Extenders RG-6 extension cables from our website or your retailer (see page 2).
height of the cell phone when it is typically in use (avoid placing the Base Unit on the floor). For the best results, avoid placing the Base Unit antenna within 2 feet of other wires or metal objects. Placing the Base Unit on a Furniture Piece The Base Unit is designed so that it easily sits on top of a furniture piece using the following steps. 1) Attach the coaxial cable, which should already be attached to the Signal Antenna, to the Base Unit.
Wall Mounting the Base Unit The Base Unit can also be easily mounted on a wall using the included mounting bracket hardware. The Base Unit should be a minimum distance of 12" from the ceiling so their is clearance for the Base Unit antenna extension. Perform the following steps to mount the Base Unit on a wall: 1) Remove the mounting bracket from the Base Unit 2) Attach the coaxial cable, which should already be attached to the Signal Antenna, to the Base Unit. 3) Attach the antenna to the Base Unit.
Note: The Signal light may flash green indicating that a call is in progress and the YX500-CEL is boosting your signal. In some cases, it may only flash at the beginning of the call. If the Signal light displays either a solid or flashing red move your phone away from the Base Unit and see the troubleshooting section. Improving Your Coverage Area Now that everything is connected and the Base Unit is plugged in, you should walk throughout the room and see that you are able to reliably place calls.
Troubleshooting the YX500-CEL Base Unit Indicator Operation Mode Normal / Idle In most cases, problems with the YX500-CEL can be diagnosed using the Base Unit’s LED indicators. Light Settings Power light = Solid Green Action None Signal light = Off Call Detected Base Unit Setup Install light = Off Power light = Solid Green None Signal light = Green May only Flash at the beginning of a call.
Mode Network Caution – Reduced Range Light Settings Power light = Solid Green Signal light = Flashing Red (20 seconds) Install light = Flashing Red (20 seconds) Action The Signal Antenna is receiving too much signal from a nearby cell tower (probably another service provider) and the Base Unit is operating with reduced gain (range). Try making one or more of the following adjustments: 1.