Content Safety Instruction ............................................................................................................................................................ 2 Minimum System Requirement & Product Feature.................................................................................................... 4 Minimum System Requirement ....................................................................................................................................
User Manual Safety Instruction Before you use this product This product has been designed with safety in mind. However, the electrical products can cause fires which may lead to serious body injury if it is not used properly. To avoid such accidents, be sure to heed the following. Legal Caution Video and audio surveillance can be forbidden by laws that vary from country to country. Check the laws in your local region before using this product for surveillance purposes.
In case of system breakdown, discontinue use and contact your authorized dealer. In case of abnormal operation If the unit emits smoke or an unusual smell, If water or other foreign objects enter the cabinet. If you drop the unit or damage the cabinet:1 Disconnect the cable and the connecting cables. 2 Contact your authorized dealer or the store where you purchased the product.
Minimum System Requirement & Product Feature System Requirement For normal operation and viewing of the network camera, it’s recommended that your system meet these minimum requirements for proper operation: Item Requirements CPU Minimum Intel® Core 2 Duo or higher (Core i3 or above is recommended) Graphic Card 256 MB RAM graphic cards (or equivalent on-board graphic cards) RAM Minimum 1 GB of RAM,(2GB or above is recommended) Operating System Window 2000, 2003, XP, Vista or Windows 7 Web Browser
Product Features SYSTEM Resolutions H.264 / MPEG-4 / Motion JPEG: Screen Resolution Higher than 1024 * 720 pixels Compressing format H.
Main Page Toolbar of Main Page 6
Client Setting Profile View Size Protocol Video Buffer Click the drop-down menu to choose video compression mode of Live View among H.264, MPEG-4, MJPEG and H.264. Note: As long as the operating system is not able to afford loading under H.264 mode, please downgrade the mode to MPEG-4 or MJPEG. Select the desired view size of image resolution between Fit Screen and Full Screen. Select the transferring protocol among TCP, UDP, and HTTP. Turn the Video Buffer function On / Off.
PTZ Click the Home button and it brings you back to the center no matter what position you are at. Move the camera view to the direction that the various arrows you click on. Use the various direction arrows to steer the camera view to the required position,and name Preset it for the specified position.
Basic Setup Account Account List The device default account and password setting is “admin / admin”. That means everyone who knows IP address can access the device including all configuration. It is necessary to create a new password if the device is intended to be accessed by specific ones. Click “Add” to create the accounts to the specific users. There are 1 default account and 9 accounts that you may assign 3 different viewer modes as you wish.
Network TCP/IP Internet Protocol Version 4 (TCP/IPv4) Obtain an IP address automatically (DHCP): If a DHCP server is installed on the network, to select this while the IP address is assigned by the DHCP server. Obtain DNS server address automatically: Select this to obtain the address of DNS server automatically. Use the following IP address: Select this option when the fixed IP address is set. IP address: Enter the IP address of the device. Subnet mask: Enter the subnet mask.
Note: Reboot the IP Camera after the network setting has been made. Note: If you connect the IP Camera with your computer directly, the default network domain of camera is 192.168.1.xx PPPoE If your ISP provides Dynamic IP with authentication by username and password, type all PPPoE information in this part. When using the PPPoE function, you need to turn on the DDNS or IP Notification function at the same time. IP address: The IP address obtained at the PPPoE connecting with network.
Use the following DNS server address: Select this when you set the fixed address as the IP address of DNS server. Primary DNS server: Enter the IP address of the primary DNS server. Secondary DNS server: Enter the IP address of the secondary DNS server. Note : 1. PPPoE (Point-to-Point Protocol over Ethernet): PPPoE is a network protocol for encapsulating Point-to-Point Protocol frames insider Ethernet frames.
3. Then click “Refresh”. All access points (AP) around you will show up. 4. Select the AP you wish to connect and click “Connect”. 5. Enter password at passphrase if you need. If you don't know the setting of the wireless AP, please ask your network administrator. WPS (F3206) WPS (Wi-Fi Protected Setup) also known as a standard for easy and secure establishment of a wireless home network. Enable it when wireless is turned on, and you will see the wireless IP and MAC of this IP camera.
Configuration Method PBC – Select to start WPS configuration. PIN – Select and click Generate new PIN to generate a new PIN code and start WPS configuration. This list is the result of network scan that only provide wireless AP with WPS function. It will be shown where the network is currently linked. Date Time Current Date / Time It displays current time and date of IP Camera and PC that you connected, and you may select the Date/Time format as you wish in the drop-down menu.
Note: The NTP server (Network Time Protocol) is the time server which is an Internet standard protocol built on the top of TCP / IP. This assures accurate synchronization to the millisecond of computer clock times in a network of computers. Video Video Setting Image Image Rotated: Select the screen display “flip”, “mirror”, or “flip + mirror. Video clip format: Select RECORDING compression format H.264、MPEG-4、MJPEG、EZVuu HQ and EZVuu LQ . Profile1(H.264): H.
Text information can be showed on the display screen, such as Date / Time and the user-defined title. Privacy Mask Privacy Mask is an area of solid color that bans users from viewing part of monitored area. Click “Add” and a setting pop-up window comes out. A translucent rectangle is located at up left of the image, drag it to where you wish to cover and resize it. Enter a descriptive name, select the color and enable it then save. Profile There are five stream profiles available for quick set-up.
Audio Audio Channel Full duplex: Select it for simultaneous communication in both direction between the connected administrator and IP CAM. It means both parties can speak and be heard at the same time. Half duplex: Select it for communication in both directions, but only one direction at a time. It cannot receive signal until the transmission has been done. Therefore, once one party speaks but can’t hear the voice, and vice versa. Talk only: It narrows down to one way just for talking.
PHONE. While the option selected, your mobile phone will receive the audio file from IP Camera. And you can choose the bit rate from 4.75k to 12.2k. However, the usage of this codec will cause frame-rate decreasing. Off: audio file won’t be transmitted by IP CAM. Audio Output Select the speaker output gain value you wish in the drop-down menu and save it. Live View Video Please refer to p.15~17 Audio Please refer to p.
Image Setting Image Enhancement Brightness: The image brightness can be adjusted in the range 0-100, the a higher value produces a brighter image. Saturation: Adjust the saturation in the range 0-100, the higher value gets more colorful image. Contrast: Adjust the image's contrast by raising or lowering the value in the range 0-100. Sharpness: Controls the sharpness applied to the image in the range 0-100. A sharper image might increase image noise especially in low light conditions.
Exposure time: Select a proper exposure time according to the light source of the surroundings. The exposure times are selectable as the following durations: 1/120second, 1/60 second, 1/30 second, 1/12 second, 1/6 second, 1/3 second, and 1second. Shorter exposure time brings less light. Gain: According to the surroundings in the low light and make the range among 1-64. The higher value makes brighter image, however brings more noise at the same time.
Click “add” , name the tour first then add in the preset position you desired to form the tour. You can manually set the PTZ speed and the interval time. Playback Client PC This is for uploading the recorded file saved in the PC and play back to see the video.
❶ Click it to upload the recorded file in the PC ❷ Click it to stop the current video ❸ Click it to pause the playing video ❹ Click it to slow down the playing speed ❺ Click it to speed up the playing speed ❻ It displays the current playing video length ❼ It displays the whole video length ❽ It displays the current video speed ❾ Click it to adjust the volume of video and mute ❿ Click it to make digital zoom Network Storage Network storage provides the storage function for saving image files to the specifie
Event Event Server Event Server Click “Add” to create a event server then the setting page pops up. Name it, select your network type put on the storage location. This is optional to create the password for certain group to use it. Then click the “Test” button to see if it works, it will show the information on the pop-up window to see your setting if has been made successfully. 3 types of event transmission offered to select.
General Name the event file and make it on or off. Trigger You may activate the following trigger types as you wish depends on various conditions: Motion Detection: Click it on for using Motion Detection function as a sensor. You must configure motion detection function before taking this as the trigger. Set minimum time interval between 2 triggers, and choose the desired detection area.
Night Mode: You may set up this action being activated continually while the event triggered or continually every period(by second) interval. Note : Only Motion Detection excludes Night Mode Schedule You may set up the event schedule as “always” or scheduled by working day, weekend or night mode. You must configure schedule before using it. Scheduled Recording General Name the recording file and make it on or off. Action File Size: You can manually write in the file size as the suggested range.
triggered. Sensitivity: Set alarm sensitivity for audio detection. The higher sensitivity is, the more sensitive it gets. Schedule The schedule is made for Event List to set the recording period. There are already 3 modes(Working Day、 Weekend and Night Mode) has been set for user, there are 7 more modes are available to set manually. System Maintenance Restart Restart button is for reboot the IP Camera digitally, you may reboot the camera manually or automatically.
Date Time Please refer to p.14~15 Security Account Please refer to p.9 IP Address Filter Once enabled it, the listed IP address are allowed or denied access to the product. Add the IP Address that you’d like to allow or deny and select allow or deny from the list and save it. HTTPS HTTPS is a URL scheme used to indicate a secure HTTP connection. It is syntactically identical to the http:// scheme normally used for accessing resources using HTTP.
Network Basic Please refer to p.10~14 Network Advanced RTSP General RTP Port Range: The default value of port range is 5000 ~ 7999 and can be changed from 1124 to 65534. RTSP Port: The default value is 554. If the IP Cameras connected with router and installed outside are over 2 sets and all of them need support RTSP, please fill the value in the blank space in the range from 1124 to 65534. RTSP Configuration Configure the RTSP by profile, then enable or disable the authentication.
and services on IP networks. Bonjour uses industry standard IP protocols to allow devices to automatically discover each other without the need to enter IP addresses or configure DNS servers. Device Name: Enter Device Name you wish. Note: How to use Bonjour in your Windows Browser UI? Please check the link below: http://www.apple.com/support/downloads/bonjourforwindows.html DDNS DDNS is a system which allows the domain name data held in a name server to be updated in real time.
FCC statement in User’s Manual (for class B) “Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.