IP1000/1050
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.
Europe – EU Declaration of Conformity Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Product Overview Introduction Basic Connection Application Easy Access Web Browsers Mobile Phone Viewing Windows Live Messenger Hardware Installation Live View Safety Instruction Minimum System Requirement Package Contents Physical Description Mounting and Cable Connecting Live View Control Panel Setting Client Setting Image Setup EZvuu Live View Client Setting Camera Console Remote Playback Remote Record OSD Toolbar Setting System Camera Network Events Help Appendix Frame Rate and
Product Overview Introduction Basic Connection Wired Connection Wireless Connection Application Table of Contents Product Overview Hardware Installation EZvuu Easy Access Live View Setting Appendix 6
Introduction The IP1000/1050 is an ultra-compact IP Camera equipped with a high sensitivity progressive scan CMOS sensor, achieving high image quality and superior low-light performance. IP1050 also supports 802.11b/g/n wireless connection with WPS. Key Features: •Maximum Resolution 640x480 (VGA) •DDNS Supported •Simultaneous MPEG-4 and Motion JPEG video stream •up to flexible 30 fps in all resolution •Wireless( IEEE 802.
Basic Connection Wired Connection Wireless Connection (Only IP1050) 1. Connect the power adaptor to IP Camera. 2. Connect IP Camera’ Ethernet port to your Hub/ Switch / Router 1. Connect the power adaptor to IP Camera. 2.
Application Table of Contents Product Overview Hardware Installation EZvuu Easy Access Live View Setting Appendix 9
Hardware Installation Safety Instruction Minimum System Requirement Package Contents Physical Description Front View Bottom View Mounting and Cable Connecting Table of Contents Product Overview Hardware Installation EZvuu Easy Access Live View Setting Appendix 10
Safety Instruction Before you use this product In case of a breakdown This product has been designed with safety in mind. However, the electrical products can cause fires which may lead to serious body injury if not used properly. To avoid such accidents, be sure to heed the following. In case of system breakdown, discontinue use and contact your authorized dealer. In case of abnormal operation Video and audio surveillance can be forbidden by laws that vary from country to country.
Minimum System Requirement Table of Contents Item CPU Graphic Card RAM Operating System Requirements Pentium 4 1600MHz (or equivalent AMD) 64 MB RAM graphic cards(or equivalent on-board graphic cards) 512 MB Windows 98, Windows ME (Please see Note) Web Browser Windows2000, 2003, XP, Vista, Windows 7, Mac OS X Leopard Internet Explore 6 or later Product Overview Hardware Installation EZvuu Easy Access Note 1.
Package Contents Camera – IP1000/IP1050 Network Camera Quick Installation Guide - To provide brief product information and quick installation and wireless setting. Software CD – Free bundled web-based 9 channels IP Surveillance Software, EZvuu wizard, User Manual and Quick Installation Guide. Ethernet cable – Assist to setup your IP Camera.
Physical Description Front View Focus Adjustment Ring - Adjust focus manually to achieve the best image quality. Power LED indicator - Power LED will light up after the IP Camera completed the boot process. Network LED indicator - Network LED will light up after the IP Camera connected with network. Built-In Microphone - Built-In Microphone for Twoway Audio.
Physical Description Table of Contents POWER LED Steady Red Steady Blue Steady Blue → Flash Purple Flash Purple → Steady Blue Flash Purple → Steady Red 30 Secs Steady Blue → Unlit Steady Blue → Unlit → Steady Blue Steady Blue → Flash Purple ETHERNET/WIRELESS LED Flashing blue Unlit Boot up process Boot up complete Push WPS button and ready for connecting wireless router/AP WPS configuration finished WPS configuration failed Push reset button and then reset Push reset button for at least 5 secs and then res
Physical Description Bottom View Power Connector - For connection of 12V DC input. Reset – When the device is empowered, press the Reset Button to reboot the device, or hold the Reset Button for 10 seconds to set the device settings back to factory default. WPS – Click to easily connect to your router equipped with WPS.
Mounting and Cable Connecting Wall and Ceiling Mounting Power and Ethernet Connecting 1. Use the 3 supplied screws to fix the base plate to a flat surface. 2. Loosen the lock ring to adjust the desired angle of the camera. 3. Tighten the lock ring. 1. Use a standard RJ-45 network cable to connect the IP Camera to the Network connection 2. Connect power adaptor to the IP Camera.
EZvuu Live View Client Setting Camera Console Remote Playback Remote Record OSD Toolbar Table of Contents Product Overview Hardware Installation EZvuu Easy Access Live View Setting Appendix 18
Live View Table of Contents Product Overview Hardware Installation EZvuu Easy Access 1. Screen Division Allocate the sub-screen display by clicking on the desired layout icon. 1 channel; 4 channel; 6 channel; 9 channel Live View 2. Logout Click to logout EZvuu Setting 3. Camera Layout Assign cameras to camera layout by drag and drop. You can double click on a particular view to extend display to full screen. Double click on the screen again to regain previous camera layout.
Live View Table of Contents Product Overview Hardware Installation EZvuu Easy Access 4. Camera Group Click to see which cameras in this group. The following is the meaning of each icon: No owner cameras group. It will flash when there’s new no owner camera. Your cameras group Friends camera group Live View Setting 5. Add Camera Click to add no owner camera to your account.
Live View Table of Contents Product Overview Hardware Installation EZvuu Easy Access 6. Screen Position Display this camera in which sub-screen. Blue means live view, green means playback, orange means remote playback and red means record. Live View 7. Camera Status Click to display control panel.
Client Setting Table of Contents Product Overview 1. Online Users Hardware Installation Display online users of your account. The limitation is simultaneously 5 users online. 2. Account Name Display the name of your EZvuu account. 3. Account Setting EZvuu Right Click your account and it will display your account setting including: "Change Password", "E-mail Setting" and "Manage the friend list". Select to change the password of your EZvuu account.
Camera Console 1. Camera Name Display nick name of this camera. You can right click to change the nick name. 2. Camera Console Click to display camera console. Click to share this camera to your friends. Click to remove this camera from your camera list. Click into setting page of this camera. Click to display playback control including: Stop playing this channel Start recording to your local PC. The icon will display when the video is on recording.
Remote Playback 1. Remote Playback Click to display remote playback console. 2. Time Selector Using the date selector, it is possible to jump straight to recordings from a specific point in time. You can drag to the blue background of timeline browser to remote playback. You also can click and to scroll monthly. If there’s no any record in last month or next month, it would jump to the month with record. 3.
Remote Record 3. Record Schedule Display the scheduled recording time of each day. The black rectangle means what day today is of the camera. The blue timeline represents the recording time of today. 4. Periodical Recording Status Display periodical recording status. You can click this icon to setup periodical recording schedule. The following is the meaning of each icon: Periodical recording enabled; Periodical recording disabled Table of Contents Product Overview Hardware Installation EZvuu 5.
OSD Toolbar 2. Playback Controls 1. OSD Toolbar Display OSD toolbar when you move your mouse on the view screen. You can click and to pull up and down the events list. The events list will flash when there is a new event. In the events OSD, it will show the recording date & time and what event triggers. You can also click and to scroll the event list. Click , and to setup the 3 motion detection zones. In the motion detection setting mode, you can click to enable/disable motion detection zone.
Easy Access Web Browsers Windows Web Browsers Mac Safari Mobile Phone Viewing Using IP Camera Via iPhone 3G Mobile Phone Streaming 2.5G Mobile Phone WAP 2.
Web Browsers Windows Web Browsers 1. Start your web browser, and enter the IP address or host name of the IP camera in the Location / Address field of your browser. Note If you only want to view the video without setting page, enter “http:///index2.htm” as your web URL. Table of Contents 3. The monitor image will be displayed in your browser. In the far left side of main configuration are Setting, Client Setting, and Image Setup. Product Overview Hardware Installation EZvuu 2.
Web Browsers Mac Safari 1. Click the Safari icon, and enter the IP address of the IP camera in the Location / Address field of your browser. Note If you only want to view the video without setting page, enter “http:///index2.htm” as your web URL. Table of Contents 2. Use the default account “admin” and default password “admin”.
Web Browsers 3. The monitor image will be displayed in your browser. In the far left side of main configuration are Setting, Client Setting, and Image Setup.
Mobile Phone Viewing Using IP Camera Via iPhone 1. Select Safari function Table of Contents 3. Type name and password. Default value is admin / admin. Then click Login In Product Overview Hardware Installation EZvuu 2. Enter IP address in your web link. 4. Live view will show up in the middle of screen.
Mobile Phone Viewing 3G Mobile Phone Streaming 2.5G Mobile Phone Browser For 3G mobile phone viewing, type “ rtsp://:/video.3gp ” into your 3G Streaming Link. is the Public IP address of your IP camera; is the RTSP port of your IP camera (Default value is 554.) Example: rtsp://100.10.10.1:554/video.3gp For 2.5G mobile phone viewing, type “http:///mobile.wml ” into your 2.5G WAP Browser. is the Public IP address of your IP camera.
Windows Live Messenger 1. Apply for a new MSN account for your Device 4. You will get IP information automatically Table of Contents Product Overview 2. Type login account and password Hardware Installation 3. Set the following settings 5.
Windows Live Messenger 6. Click Action button and choose Start control panel 7.
Live View Live View Control Panel Setting Client Setting Image Setup Table of Contents Product Overview Hardware Installation EZvuu Easy Access Live View Setting Appendix 35
Live View Control Panel Full Screen Snapshot Table of Contents Product Overview Hardware Installation EZvuu Easy Access Live View Setting Video Play Audio In Audio Out Zoom In/Out Appendix 36
Setting Setting This function is only for the Administrator. Click this button to get into the setting page. HELP is an online help and support. It provide solutions immediately. Table of Contents Product Overview Hardware Installation EZvuu There are four sub-folders including System, Camera, Network, and Events and a Question mark inside. Click question mark will pop-up a new window and you can get answers online without user manual.
Client Setting Client Setting This function is only for the administrator and client. Mode Click the pull-down box to choose between MPEG-4 MJPEG, and JPEG video compression mode. MJPEG streaming is unavailable if RTSP mode is “On.” Video Size Select the desired display image resolution to 640X480 or 320X240. Table of Contents Product Overview Hardware Installation EZvuu Video Buffer Turn the Video Buffer function ON / OFF.
Image Setup Brightness The higher value the brightness is, the brighter the image is. Contrast The contrast is a measure of a display system, defined as the ratio of white to black that the system is capable of producing. The higher value the contrast is, the more delicate of color you can have.
Setting System Information Date/Time Account System Log Initialize Camera General MPEG4 Computer View Mobile View MJPEG Network Information EZvuu PPPoE DDNS UPnP IP Notification WPS Wireless Messenger Events FTP Client SMTP Network Storage Motion Detection Schedule Help Table of Contents Product Overview Hardware Installation EZvuu Easy Access Live View Setting Appendix 40
System Information The Information page provides the product factory information which includes Product Name, Firmware Version and Web Version. Day/Time Date / Time format Pull down box to select different time display formats. Table of Contents Adjust Keep current setting Keep the current date and time of this IP Camera. Synchronize with PC Keep the date and time the same PC. Manual setting Adjust manually the date and time of this IP Camera.
System Account User name The device fault account and password setting is “admin / admin”. That means everyone who knows IP address can access the device including all configuration. It is necessary to assign a password if the device is intended to be accessed by others. Set a user name between 4-16 characters. Table of Contents Password Set a password between 4-16 characters. Re-type Password Product Overview Re-type the password to confirm.
System System Log Initialize The System Log function allows users to review any changes and events happened. The system starts logging automatically after started. Reboot Reboot this IP Camera and it takes two minutes to reboot this IP Camera. Factory Default Reset this IP Camera to the factory default setting.. Don't turn off this IP Camera until the device reboots. Backup Setting Table of Contents Product Overview Hardware Installation Backup the setting data of this IP Camera.
Camera General Night Mode You can choose Auto / Off. If you choose Auto option, the camera will adjust automatically to perform well when the environment is dark. Exposure Mode You can choose the environment among 50 Hz, 60 Hz , and Outdoor. White Balance You can choose the white balance to Auto, Florescent, Incandescent and Black & White. LED Indicator Table of Contents Product Overview Hardware Installation EZvuu Turn on/off the LED indicator. RTSP Switch RTSP “On” or “Off.
Camera MPEG4 – computer view If RTSP is ON, the option of Viewer Authentication & Multicast Streaming will appear. Time to Live Set the maximum TTL that multicast can pass through. Image Size Specify the image size when the network camera transmits Frame Rate Set the frame rate of the MPEG4 image. Quality Auto The quality and bitrate will be adjusted automatically according to the frame rate. Fixed Quality You can select the value of quality.
Camera MPEG4 – mobile view If RTSP is ON, the option of Viewer Authentication & Multicast Streaming will appear. Time to Live Set the maximum TTL that multicast can pass through. Image Size Specify the image size when the network camera transmits Frame Rate Set the frame rate of the MPEG4 image. Quality Auto The quality and bitrate will be adjusted automatically according to the frame rate. Fixed Quality You can select the value of quality.
Camera MJPEG If RTSP is OFF, the option of Image Size & Frame Rate & Quality will appear. Image Size Specify the image size when the network camera transmits Frame Rate Set the frame rate of the MJPEG image. Quality Auto The quality and bitrate will be adjusted automatically according to the frame rate. Fixed Quality You can select the value of quality. Fixed Bitrate Set the bitrate of MPEG4 image transmission for a line.
Network Information Display the MAC address of the device. Use the following IP address Select this when the fixed IP address is set. IP address Enter the IP address of the device. Subnet mask Enter the subnet mask. Default gateway Enter the default gateway. Use the following DNS server address Select this when you set the fixed address as the IP address of DNS server. Primary DNS server Enter the IP address of the primary DNS server.
Network EZvuu EZvuu, also known as zero-configuration networking, enables automatic to find your devices on IP networks. EZvuu uses Windows Live Messenger protocols to allow devices to automatically discovered without the need to enter IP addresses or configure DNS servers. Table of Contents Product Overview Hardware Installation EZvuu Easy Access Name Live View Show your device name on EZvuu.
Network PPPoE If your ISP provides Dynamic IP with authentication by username and password, type all PPPoE information in this part. When you use the PPPoE function, you need to turn on the DDNS or IP Notification function at same time. IP Address The IP address obtained at the PPPoE connecting with network. User ID Enter the user ID for authentication necessary for PPPoE connections. Password Enter the password for authentication necessary for PPPoE connections.
