Use and Care Manual

ZAR® Interior Oil Base Poly PRO
ZAR® Interior Oil Base Poly PRO is a fast
drying contractor formula which is perfect
for oors, furniture, cabinets, and
woodwork. It provides beautiful, long-lasting
protection for all types of interior wood. It
self-levels and gives superior protection in
fewer coats.
Fast drying contractor formula
Residential and commercial use
Self-leveling for a superior finish
Low odor resin technology
A fast drying polyurethane nish for oors,
furniture, paneling, cabinets, counter tops
and woodwork.
For interior use only. Do not apply over
wood llers or nishes containing wax or
stearates. Do not thin.
COMPOSITION:
Oil base
SHEEN:
Gloss >90% @ 60º
Satin 45 ± 3 @ 60º
Mae 20 ± 3@ 60º
% WEIGHT SOLIDS:
40 ± 1
DENSITY (LBS./US GAL.):
7.3-7.4 (S.G. 0.87)
VISCOSITY:
A-1 – A-2 Gardner bubble
pH:
N/A
DRY TIME:
• To touch: 30 minutes - 1 hour
• To recoat: 2 hours
• Light use: 24 hours
• Moderate use: 3-5 days
• Maximum use: 7 days
Note: Maximum cure and dry time will
be prolonged when slightly humid and
damp, cool conditions prevail.
CLEAN UP:
Paint thinner or mineral spirits
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state, and federal
regulations.
COVERAGE (SQ. FT./GAL.):
400-500 sq. . (37.1 m
2
-46 m
2
)/gal
@ 1 mil
Note: Actual coverage will vary
depending upon application method,
surface texture, and porosity.
RECOMMENDED FILM THICKNESS/COAT:
2 wet mils/coat
FLASH POINT:
104ºF, (40ºC)
SHELF LIFE:
5 Years unopened container
FREEZE/THAW:
N/A
CONTAINER SIZES:
One quart (946 mL) and one gallon
(3,785 L) cans
Does not exceed 550 g/L
N/A
Do not thin.
New Wood: Sand smooth using ne
sandpaper. Remove sanding dust with a tack
cloth or cloth dampened with paint thinner
or mineral spirits.
If open-grained woods are to be lled, use a
ller that does not contain stearates or waxes
such as ZAR® Wood Patch or ZAR®
Trowelable Wood Patch.
Old Clear Finishes in Good Condition:
Remove grease, dirt, and wax. Sand lightly in
the direction of the grain to remove any gloss.
Clean sanding dust with a tack cloth or cloth
dampened with paint thinner or mineral
spirits to remove any remnants of dust prior
to application and allow to dry.
Old Clear Finishes in Poor Condition,
Lacquer or Shellac: Remove completely. If
the old nish contains wax, regardless of
condition, remove completely. Sand and
remove sanding dust with a tack cloth or cloth
dampened with paint thinner or mineral
spirits.
Test ZAR® Interior Oil Base Poly PRO in an
inconspicuous area for compatibility.
If you scrape, sand, or remove old paint, you
may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-
approved respirator to control lead exposure.
Clean up carefully with a HEPA vacuum and a
wet mop. Before you start, nd out how to
protect yourself and your family by
contacting the National Lead Information
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.UGL.com
Z A R ® W O O D F I N I S H I N G P R O D U C T S
O V E R
Paint
Thinner
DRY TIME:
1-2 Hours
Recoat 2 Hours
CLEAN-UP:
Paint inner or
Mineral Spirits
COVERAGE:
2 Coats
SPREAD RATE:
400-500 Sq.
Ft./Gallon