EN User manual Washing machine ZWT 3304 ZWT 3204
Product description 1 The control panel 2 Lid handle 3 Filter access cover 4 Adjustable levelling feet Control panel 1 2 3 1 Programme selector 2 Pushbuttons and their functions 4 "Door locked" light 5 "Start/Pause" pushbutton 3 Display 6 "Delay start" pushbutton 2 4 5 6 www.zanussi.
Dispenser box Prewash Wash Softener (do not fill above the MAX symbol M ) Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. Children and vulnerable people safety Warning! Risk of suffocation, injury or permanent disability.
• Obey the maximum load volume of 6 kg (refer to the “Programme chart” chapter). • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
• The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. Use Warning! Risk of injury, electrical shock, fire, burns or damage to the appliance. • Use this appliance in a household only. • Obey the safety instructions on the detergent packaging.
Selection of desired programme Turn the programme selector to the required pushbutton programme. The “Start/Pause” flashes green. If you turn the programme selector to another programme while a cycle is in progress, the appliance will ignore the new selected programme. “Err” flashes and the “Start/Pause” pushbutton flashes red for a few seconds. Selecting the spin speed pushbutton to change the Press the “Spin” spin speed.
When the light is off, you can add washing by proceeding as follows. Press the “Start/ Pause” pushbutton : the corresponding light will flash green while the appliance is paused. The lid can only be opened around 2 minutes after the washing machine has come pushbutto a stop. Press the “Start/Pause” ton again to continue the programme. Modifying the programme in progress Before making any changes to the current programme, you need to pause the washing mapushchine by pressing the “Start/Pause button.
Programme / Type of washing Load 6,0 kg Spin : A spin cycle from 500 to 1300/12004) rpm after a Rinse hold. Possible options Delay start 1) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, the “Cottons with Eco option” and “Cottons with Eco option” are respectively the “standard 60° C cotton programme” and the “standard 40° C cotton programme”.
Descaling the appliance To descale the appliance, use an appropriate non-corrosive product designed for washing machines. Read product label for recommended amounts and how often descaling should be carried out. The exterior Use warm soapy water to clean the exterior of the appliance. Never use alcohol, solvents or similar products.
Problems Causes The appliance fills but empties straight away : • the drainage U-piece is fixed too low (see installation section). The washing machine doesn’t rinse or doesn’t empty : • the drain hose is blocked or bent, • the drainage filter is obstructed, • the out of balance detector has been activated : washing is unevenly distributed in the drum, • the “Drain” programme or “Night Silence Plus” or “Rinse hold” option have been selected, • the height of the drainage U-piece is unsuitable.
Problems Causes The E20 error code appears in the display2)and the “Start/Pause” pushbutton flashes red3): • • • • • the drainage filter is obstructed, the drain hose is blocked or bent, the drain hose is fixed to high (see "Installation" section), the drainage pump is blocked, the standpipes blocked. The E10 error code appears in the display2) and the “Start/Pause” pushbutton flashes red3): • the water tap is closed, • the water supply has been cut off. • a red tab appears on the water inlet hose1).
Installation Remove all protective packaging for transit before using for the first time. Keep in case needed for future transit: Transporting a non-secured appliance may damage internal components and cause leakages and malfunctions. The appliance can also be damaged through physical contact. Water supply Install the supplied water inlet hose at the rear of your washing machine by proceeding as follows. Do not reuse an old hose. The water inlet hose can not be extended.
Environment Disposing of the appliance All materials carrying the symbol are recyclable. Dispose of them at a waste collection site (enquire at your local council) for collection and recycling. When disposing of your appliance, remove all parts which could be dangerous to others: cut off the power supply cable at the base of the appliance. on the product or on its packThe symbol aging indicates that this product may not be treated as household waste.
www.zanussi.
www.zanussi.
108740701-A-372013 www.zanussi.
