EN User manual Washing Machine ZWO 3101
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Technical information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 3 4 5 6 Hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Water connection • Do not connect the appliance with old hoses already used. Only use new hoses. • Make sure not to cause damage to the water hoses. • Do not connect the appliance to new pipes or pipes not used for a long time. Let the water flow for some minutes, then connect the inlet hose. • The first time you use the appliance, make sure that the water hoses and the couplings do not have leakages. Electrical connection • Make sure that the appliance is earthed.
Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 10 bar (1 MPa) Cold water Water supply 1) Maximum load Cotton Spin speed Maximum 3.5 kg 1000 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread.
Control panel 1 9 8 7 6 5 4 3 2 1 Programme knob 6 Rinse hold button 2 Start button 3 Display 7 Prewash button 4 Easy iron button 9 Delay Star button 8 Spin button 5 Extra rinse button Programme knob 1 B • The default spin speed of the programme. • 'No Spin' (00). Turn this knob to set a programme. Start/Pause button 2 C • The display symbols. The symbols appear on the display when the related function is set. Press this button to start a programme.
Extra rinse button 5 Press this button to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. Rinse Hold button 6 Press this button to activate the 'Rinse Hold' function. Set this function to prevent fabric creases. The appliance does not drain the water when the programme is completed. To drain the water refer to ‘At the end of the programme’.
Programme Temperature Synthetics 60° C Sport 40° C Synthetic mixed 30° C Delicates Shirts 40° C Wool 40° – Cold Handwash 30° C Quick wash 35° C Daily 40° C Cold wash Rinse Spin Type of load and soil Weight of load Programme phases Possible functions Synthetic or mixed fabric items with nor- Wash mal level of soil Rinses max. 1.7 kg Spin phase at 800 rpm Special programme for sport and casual items with normal or light level of soil.
Programme Temperature Type of load and soil Weight of load Programme phases Possible functions To cancel the programme that it operates or to deactivate the appliance. Consumption values Programme1) Energy consumption (KWh)2) Water consumption (litre)2) White Cottons 90 °C 1.5 43.5 Cottons 30 °C 0.26 28 Synthetics 60 °C 0.7 44 Synthetics 40 °C 0.38 38.5 Delicates 40 °C 0.4 41.5 Wool 40 °C 0.25 44.5 Handwash 30 °C 0.17 51 1) Refer to the display for the programme time.
Detergents and additives Water hardness • Only use detergents and additives specially made for washing machines. • Do not mix different types of detergents. • To help the environment, do not use more than the correct quantity of detergent. • Obey the instructions that you find on the on packaging of these products. • Use the correct products for the type and colour of the fabric, the programme temperature and the level of soil. • If you use liquid detergents, do not set the prewash phase.
Caution! Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. Using the liquid detergent • Pull out the detergent dispenser until it stops. • Pull out the detergent divider from its position (A). A Filling the detergent and additives • Put it into the special guides in the middle of the compartment for the washing phase. Caution! Use only specified detergents for washing machine.
Change a function You can change only the delay and spin function before they operate. Press the related button to set the new value. Set the delay start 1. 2. Press the delay start button again and again until the display shows the number hours. Press the start button, the appliance starts the countdown of the delay start. The symbol h flashes in the display and the start button indicator is off. When the countdown is completed, the programme starts automatically and the start button indicator comes on.
Do this separately from the laundry wash. • Remove the top part of the liquid additive compartment. Clean all the parts with water. Maintenance wash With the low temperature programmes it is possible that some detergent stays in the drum. Make regularly a maintenance wash. To do this: • Empty the laundry from the drum. • Set the hottest cotton wash programme • Use a correct quantity of powder detergent with biological properties.
2. 3. 4. 1 Put a container below the recess of the drain pump to collect the water that flows out. Unscrew the filter to let the water flow out. When the container is full of water, screw the filter again and empty the container. Do steps 3 and 4 again and again until no more water flows out from the drain pump. 5. Unscrew the filter and remove it. 6. Remove fluff and objects from the pump. 7. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre.
Frost precautions 5. If the appliance is installed in an area where the temperature can be less than 0 °C, remove the remaining water from the inlet hose and the drain pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3. Remove the water inlet hose 4. Put the two ends of the inlet hose in a container and let the water flow out of the hose. 6. Empty the drain pump. Refer to the emergency drain procedure When the drain pump is empty, install the inlet hose again.
Problem The appliance does not drain the water. The spin phase does not operate. There is water on the floor. You cannot open the appliance door. The appliance makes an unusual noise. Possible cause Possible solution The connection of the water inlet hose is not correct. Make sure that the connection is correct. The water pressure is too low. Contact your local water authority. The water drain hose is damaged. Make sure that the water drain hose has no damages.
Problem Possible cause Possible solution Too much laundry load. Decrease the laundry load. After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the service centre. Service Refer to the information supplied with this appliance for guarantee condition and point of contact. The information to give to the service is on the rating plate. We recommend that you write the information here: Model ..................
5. Put the front piece on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 1 3. Remove the internal film. 2 6. Remove the polystyrene protection from the bottom. A 7. 4. Open the door and remove all the items from the drum. 8. Install the plastic cover (A), removed from the top of the packaging, to the bottom of the appliance. Remove the adhesive strip and close the bottom of the appliance.
Positioning and levelling 2 • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units 1 x4 9. Remove the four bolts with a key. Pull out the plastic spacers. Remove the power supply cable and the drain hose from the hose holders. x4 • Loosen or tighten the feet to adjust the level.
The inlet hose • Connect the hose to the appliance. Loose the ring nut to set it in the correct position. • Connect the water inlet hose to the cold water tap with 3/4 thread. • On the edge of a sink. Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. Caution! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose.
• To a sink spigot. Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. 20 • Directly to a built-in drain pipe in the room wall and tighten it with a clip.
155219240-A-352011 www.zanussi.