EN User manual Washing Machine ZWHB 7130 P ZWHB 7160 P
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ 5 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Special accessories _ _ _ _ _ _ _ _ _ _ _ _ _ 11 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily
• Obey the maximum load volume of 7 kg (refer to the “Programme chart” chapter). • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. Use Warning! Risk of injury, electrical shock, fire, burns or damage to the appliance.
When you intend to start the appliance up again, make sure that the room temperature is above 0°C. Environment concerns Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
1 Detergent dispenser drawer 7 Water drain hose 2 Worktop 8 Drain hose support 3 Control panel 9 Hose holders 4 Door opening handle 10 Water inlet hose 5 Rating plate (on the inner edge) 11 Mains cable 6 Front adjustable feet 12 Back feet Child safety device To activate this device, rotate the button (with- To disable this device and restore the possibilout pressing it) inside the door clockwise until ity of closing the door, rotate the button antithe groove is horizontal.
1 x3 A B x3 x1 C 2 x2 Warning! Remove and keep all transit devices so that they can be refitted if the appliance ever has to be transported again. • Spread the front piece on the floor behind the appliance and then lay the appliance carefully rear side down on it. Make sure that no hoses are crushed in the process. • Remove the polystyrene base from the bottom. • Return appliance to it's upright position. Necessary tools 10 mm 30 mm • Remove the external film. Use a cutter, if necessary.
• Unscrew the three bolts and remove the hose holders. • Slide out the relevant plastic spacers. Warning! Do not remove the drain hose from the rear support. Remove this hose only if it is necessary to drain the water. Refer to "Frost precaution" and "What to do if". • Plug the smaller upper hole and the two large ones with the corresponding plastic plug caps. Positioning and levelling x4 Level the appliance by raising or lowering the feet. The appliance MUST be level and stable on a flat hard floor.
Water drainage Accurate levelling prevents vibration, noise and displacement of the appliance during operation. Repeat the levelling action, if the appliance is not level and stable. Warning! This appliance is free standing only. Do not remove the worktop for any reason. Firstly form a hook in the end of the drain hose using the plastic hose guide supplied with the appliance . The end of the drain hose can be positioned in four ways: • Hooked over the edge of a sink using the plastic hose guide.
MAX 100cm • Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose. The drain hose must not be kinked. If your drain hose looks like this (see beside) you do not require the “U” piece”. Just push the hose firmly in to the standpipe. • Directly to a built-in drain pipe in the room wall.
If you require any further advice please contact your local water authority. SHOWER SINK TOILET BATH BIDET WASHING MACHINE DISHWASHER RAINWATER ‘RUN-OFF’ SURFACE WATER DRAINS & SEWERS UNTREATED DISCHARGE RIVER FOUL DRAIN FOUL SEWERS • Do not use multi-way plugs, connectors and extension cables. There is a risk of fire. • Do not replace or modify the mains cable yourself. Contact the After Sales Service.
Personalisation Buzzer The appliance is provided with an acoustic device, which sounds in the following cases: • at the end of the cycle; • if there is a fault. Rinse Hold Quick Wash By pressing the 4 and 5 buttons simultaneously for about 6 seconds, the acoustic signal is deactivated (except if there is a fault). By pressing these 2 buttons again, the acoustic signal is reactivated.
Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole. Mould stains: treat with bleach, rinse well (whites and fast coloureds only). Grass: soap lightly and treat with bleach (whites and fast coloureds only). Ball point pen and glue: moisten with acetone1), lay the garment on a soft cloth and dab the stain.
Degrees of water hardness Water hardness is classified in so-called “degrees” of hardness. Information on hardness of the water in your area can be obtained from the relevant water supply company, or from your local authority. If the water hardness degree is medium or high we suggest you to add a water softener following always the manufacturer’s instructions. When the degree of hardness is soft, readjust the quantity of the detergent.
• Rotate the flap downwards. • Carefully put the drawer back. • Powder detergent. • With programmes with prewash. • Do not use liquid detergent if the washing programme doesn't start immediately. In all above listed cases, use the flap in "UP" position . Measure out the fabric softener • Measure out the detergent. For the quantity of detergent, refer always to what is written on the product packing and ensure that the detergent can be poured in the drawer.
1 2 3 4 5 7 8 6 9 10 Turn the programme selector dial to the required programme. The selector dial can be turned either clockwise or counter-clockwise. The green pilot light of the button 9 starts flashing: the appliance is now switched on.
Spin Reduction By selecting a programme, the appliance proposes automatically the maximum spin speed provided for that programme. Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a different speed. The relevant light illuminates. 3 Rinse Hold By pressing this button the corresponding pilot light illuminates. By selecting this function the water of the last rinse is not emptied out to prevent the fabrics from creasing.
Display 7 7.1 7.2 7.3 The display shows the following information: 7.1 Delay Start icon 7.2 Child safety lock This device permits you to leave the appliance unattended during it's functioning. 7.3 • Duration of the selected programme After selecting a programme, the duration is displayed in ). The duration is calhours and minutes (for example culated automatically on the basis of the maximum recommended load for each type of fabric.
Selecting the delay start : • Select the programme and the required options. • Select the delay start by pressing button 8. • Press button 9: – the appliance starts its hourly countdown. – the programme will start after the selected delay has expired. You can cancel or modify the delay time at any moment, before you press button 9. Cancelling the Delay Start after having started the programme: • Set the appliance to PAUSE by pressing button 9. • Press button 8 once. On the display will appear '.
• To restart the programme from the point at which it was interrupted, press the button 9. • After the programme has started the door is locked. If, for any reason, you need to open the door, set firstly the appliance to PAUSE by pressing the button 9. After a few minutes it will be possible to open the door. If the door remains locked, this means that the appliance is already heating or that the water level is too high.
Door seal At the end of every cycle, check from the door seal and remove objects that could be trapped in the fold. Washing programmes Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options COTTONS 90°C- Cold Main wash - Rinses - Maximum spin speed at 1300 rpm for ZWHB7130P - 1600 rpm for ZWHB7160P Max. load 7 kg - Reduced load 3,5 kg White, coloured cotton and linen. Normally soiled items.
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options MIX 20° 20° 3) Main wash - Rinses - Maximum spin speed at 900 rpm Max. load 3,5 kg Highly energy efficient cold wash programme for lightly soiled laundry. This programme requires a detergent which is active in cold water. SPIN RINSE HOLD EXTRA RINSE DELAY START DELICATES 40°C- Cold Main wash - Rinses - Maximum spin speed 700 rpm Max.
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options EASY IRON 60°C- Cold Main wash - Rinses - Maximum spin speed at 900 rpm In order to obtain the best anti-creasing result, reduce the load of synthetic items. (Recommended load 1 kg) Synthetic or mixed fabrics. Gentle wash and spin to avoid any creasing. The appliance performs additional rinses.
Programmes Load (kg) Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Remaining moisture (%)1) Cottons 60 °C 7 1.30 73 170 522) / 443) Cottons 40 °C 7 0.85 73 145 522) / 443) Synthetics 40 °C 3,5 0.65 58 95 35 Delicates 40 °C 3,5 0.65 71 77 35 2 0.30 48 55 30 Wool/Hand wash 30 °C Standard cotton programmes Standard 60 °C cotton 7 1.07 50 236 522) / 443) Standard 60 °C cotton 3,5 0.
• To aid cleaning, the top part of the additive compartment should be removed. • turn the drum and align the filter cover (FILTER) with the arrow on the door seal; • open the filter cover by pressing the special hook and by rotating the cover upwards; • Use a stiff brush to clean and remove all washing powder residue. • Clean all the removed parts of the dispenser drawer under a tap to remove any traces of accumulated powder. Warning! Keep the filter cover open until the filter removal.
To clean the water inlet filters: The filter is inserted correctly when the indicator on its top is visible and blocked. • close the filter cover; • insert the mains plug again. Cleaning the water inlet filters Important! If the appliance doesn't fill, it takes a long time to fill with water, the starting button flashes red or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked . • Turn off the water tap.
Fault code and malfunction Possible cause / Solution The water tap is closed. • Open the water tap. The inlet hose is squashed or kinked. • Check the inlet hose connection. The filter in the inlet hose or the inlet valve filter are blocked. • Clean the water inlet filters (read "Cleaning the water inlet filters" for more details). Problem with the water supply The drain hose is squashed or kinked. • Check the drain hose connection. The drain filter is clogged.
Malfunction Possible cause / Solution The appliance does not start: The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no power at the socket. • Please check your domestic electrical installation. The main fuse has blown. • Replace the fuse. The programme selector dial is not correctly positioned and the button 9 has not been pressed. • Please turn the selector dial and press the button 9 again. The delay start has been selected.
Malfunction Possible cause / Solution Spinning starts late or the appliance does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed in the drum, the appliance will not spin.
www.zanussi.
www.zanussi.
192977480-A-092013 www.zanussi.
