EN User manual Washing Machine ZWH 7120 P ZWH 7140 P ZWH 7160 P
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ 4 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Washing programmes _ _ _ _ _ _ _ _ _ _ _ Consumption values _
• All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in the user manual. • This appliance is free standing only. DO NOT build it in under a counter and DO NOT remove the worktop for any reason. • After having installed the appliance, check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable against the wall.
• The packaging components (e.g. plastic film, polystyrene) can be dangerous to children danger of suffocation! Keep them out of children’s reach. • Keep all detergents in a safe place out of children’s reach. • Make sure that children or pets do not climb inside the drum. To prevent children and pets becoming trapped inside the drum this appliance incorporates a special feature. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal.
household waste disposal service or the shop where you purchased the product. Packaging materials are The materials marked with the symbol recyclable. >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers. • Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). • The machine works more economically if it is fully loaded.
Technical data Dimensions Width Height Depth 60 cm 85 cm 54 cm Electrical connection Information on the electrical connection is given on the rating plate, on the inner edge of the appliance door. Water supply pressure Minimum Maximum 0,05 MPa 0,8 MPa Maximum Load Cotton 7 kg Spin Speed Maximum 1200 rpm (ZWH 7120 P) 1400 rpm (ZWH 7140 P) 1600 rpm (ZWH 7160 P) Installation Unpacking • Remove the external film. Use a cutter, if necessary.
• Remove the polystyrene base from the bottom. • Return appliance to it's upright position. • Open the door and remove the plastic hose guide, the bag containing the instruction booklet and the plastic plug caps from the drum. • Unscrew the three bolts and remove the hose holders. • Slide out the relevant plastic spacers. Warning! Do not remove the drain hose from the rear support. Remove this hose only if it is necessary to drain the water. Refer to "Frost precaution" and "What to do if".
Positioning and levelling Water inlet Connect the hose to a tap with a 3/4” thread. 35° 45° x4 Level the appliance by raising or lowering the feet. The appliance MUST be level and stable on a flat hard floor. If necessary, check the setting with a spirit level. Any necessary adjustment can be made with a spanner. Loosen the ring nut to angle the hose to the left or right depending on the position of your water tap. Do not place the inlet hose downwards.
MAX 100cm Tie the plastic hose guide to the tap with a string to prevent that the drain hose unhooks when the appliance is emptying. • Onto a sink outlet spigot. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose. The drain hose must not be kinked. If your drain hose looks like this (see beside) you do not require the “U” piece”. Just push the hose firmly in to the standpipe.
Connections overview 0.5 bar (0.05 MPa) 8 bar (0.8 MPa) max. 100 cm min. 60 cm max. 100 cm min. 60 cm ~max.400 cm In the interest of the environment The appliance should be connected to the FOUL drainage system, the water will then be taken to a sewage works for treatment before being discharged safely into a river. It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution.
Warning! The appliance is supplied with a 13 amp plug attached. Use a 13 amp ASTA approved (BS 1362) fuse if it is necessary to change the fuse in the plug supplied. A cut off plug inserted into a 13 amp socket is a serious safety danger. Make sure that it is disposed of safely. First use • Ensure that the electrical and water connections comply with the installation instructions. • Ensure that the drum is empty. laundry in the machine, to remove any manufacturing residue from the drum and tub.
Before Loading The Laundry Important! Make sure that no metal objects are left in the laundry (e.g. hair clips, safety pins, pins). Button up pillowcases, close zip fasteners, hooks and poppers. Tie any belts or long tapes. Remove any hooks (e.g curtains). • Never wash whites and coloureds together. Whites may lose their «whiteness» in the wash. • New coloured items may run in the first wash; they should therefore be washed separately the first time.
Close the door gently Warning! Make sure that any fabrics were not trapped when closing the door. relevant water supply company, or from your local authority. If the water hardness degree is medium or high we suggest you to add a water softener following always the manufacturer’s instructions. When the degree of hardness is soft, readjust the quantity of the detergent.
• Measure out the detergent. For the quantity of detergent, refer always to what is written on the product packing and ensure that the detergent can be poured in the drawer. • Remove the drawer. Push the drawer edge outwards where indicated by the arrow (PUSH) to facilitate drawer removal. The flap is down and you wish to use powder detergent: • Rotate the flap upwards. Ensure to fit the flap completely in. • Carefully put the drawer back. • Measure out the detergent.
Set your washing programme The control panel permits to select a washing programmes and different options. When an option button is selected, the corresponding pilot light is on. Otherwise it is off. For compatibility among washing programmes and options, see the "Washing Programmes". If an incorrect option is selected, the integrated red pilot light of the button 9 flashes 3 times and the display shows the message Err.
2 Temperature button Push the temperature button to select the most suitable temperature for washing your laundry. Cold: Cold wash. 3 Spin reduction By selecting a programme, the appliance proposes automatically the maximum spin speed provided for that programme. Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a different speed. The relevant light illuminates. 4 Rinse Hold By pressing this button the corresponding pilot light illuminates.
7 Display 7.1 7.2 7.3 The display shows the following information: 7.1 Delay Start icon 7.2 Child safety lock This device permits you to leave the appliance unattended during it's functioning. 7.3 • Duration of the selected programme After selecting a programme, the duration is displayed in ). The duration is calhours and minutes (for example culated automatically on the basis of the maximum recommended load for each type of fabric.
8 Delay Start Delay Start The programme can be delayed from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button. Before you start the programme, if you wish to delay the start, press this button to select the desired delay. The selected delay time value will appear on the display for a few seconds, then the duration of the programme will appear again. You must select this option after you have set the programme and before you start the programme.
9 Start/ Pause Start /Pause Start the programme by pressing the button 9 • To start the selected programme, press the button 9, the corresponding green pilot light stops flashing. The pilot light 10 illuminates to indicate that the appliance starts operating and the door is locked. If you have chosen a delayed start, the appliance will begin the countdown. • To interrupt a programme which is running, press the button 9: the corresponding green pilot light starts flashing.
the door open to prevent the formation of mildew and unpleasant smells. button the appliance will come out of the energy saving status. Warning! If there are children or pets in the house, activate the child safety device in the inner side of the door frame (for more details read " Child safety" in the chapter "Safety Information"). Door seal At the end of every cycle, check from the door seal and remove objects that could be trapped in the fold.
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options SYNTHETICS 60° - Cold Main wash - Rinses - Maximum spin speed at: 1200 rpm for model ZWH 7120 P; 900 rpm for model ZWH 7140 P and for model ZWH 7160 P Max. load 3,5 kg - Reduced load 2 kg Synthetic or mixed fabrics: underwear, coloured garments, non-shrink shirts, blouses . Normally soiled items.
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Compartment DRAIN Draining of water For emptying out the water left in the drum in the programmes with Rinse Hold option. SPIN Drain and long spin at maximum spin speed: 1200 rpm for model ZWH 7120 P; 1400 rpm for model ZWH 7140 P; 1600 rpm for model ZWH 7160 P Max.
They are the most efficient programmes in terms of combined energy and water consumptions for washing normally soiled cotton laundry. The water temperature of the washing phase may differ from the temperature declared for the selected programme. Consumption values Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Remaining moisture (%)1) ZWH 7120 P Remaining moisture (%)1) ZWH 7140 P Remaining moisture (%)1) ZWH 7160 P Cottons 60 °C 7 1.
Care and cleaning Warning! Switch the appliance off and remove the mains plug from the socket before any cleaning action. Maintenance Wash With the use of low temperature washes it is possible to get a build up of residues inside the drum. We recommend that a maintenance wash be performed on a regular basis. To run a maintenance wash: • The drum should be empty of laundry. • Select the hottest cotton wash programme. • Use a normal measure of detergent, must be a powder with biological properties.
• open the filter cover by pressing the special hook and by rotating the cover upwards; Warning! Keep the filter cover open until the filter removal. • before removing the filter, remove any fluff or small objects from around the filter; The filter is inserted correctly when the indicator on its top is visible and blocked. • close the filter cover; • insert the mains plug again.
What to do if… The appliance does not start or stops during operation. Certain problems are due to lack of simple maintenance or oversights, which can be solved with the help of the indications described in the charts, without calling out an engineer. During appliance operation it is possible that the red pilot light of the button 9 flashes, the Fault code and malfunction display shows a fault code and the buzzer sounds to indicate that the appliance is not working.
Fault code and malfunction Possible cause / Solution The door has not been closed or is not closed properly. • Close firmly the door. Door open The appliance does not start or stops during operation without any visible alarm. Malfunction Before contacting your local Service Centre, please carry out the checks listed below. Possible cause / Solution The appliance does not start: The plug is not properly inserted in the power socket. • Insert the plug into the power socket.
Malfunction Possible cause / Solution The door will not open: The programme is still running. • Wait the end of washing cycle. The door lock has not been released. • Wait until the door lock is released. Open the door when the pilot light 10 is off. There is water in the drum. • Select drain or spin programme to empty out the water. The appliance vibrates noisily: The transit bolts and packing have not been removed. • Check the correct installation of the appliance.
Mod Prod . ... . No. ... ... ... ... .. Ser. No. ... ... ... Model description (MOD.) ............................... Product number (PNC) ................................... Serial number (S.N.) ....................................... Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... ... ... www.zanussi.
www.zanussi.
www.zanussi.
192987381-A-172012 www.zanussi.