EN User manual Washing Machine ZWH 7120 P
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ 5 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Special accessories _ _ _ _ _ _ _ _ _ _ _ _ _ 11 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily
• Obey the maximum load volume of 7 kg (refer to the “Programme chart” chapter). • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
• Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. Use Warning! Risk of injury, electrical shock, fire, burns or damage to the appliance. • Use this appliance in a household environment. • Obey the safety instructions on the detergent packaging. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance.
Environment concerns Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Packaging materials are reThe materials marked with the symbol cyclable.
1 Detergent dispenser drawer 7 Water drain hose 2 Worktop 8 Drain hose support 3 Control panel 9 Hose holders 4 Door opening handle 10 Water inlet hose 5 Rating plate (on the inner edge) 11 Mains cable 6 Front adjustable feet 12 Back feet Child safety device To activate this device, rotate the button (with- To disable this device and restore the possibilout pressing it) inside the door clockwise until ity of closing the door, rotate the button antithe groove is horizontal.
1 x3 A B x3 x1 C 2 x2 Warning! Remove and keep all transit devices so that they can be refitted if the appliance ever has to be transported again. • Spread the front piece on the floor behind the appliance and then lay the appliance carefully rear side down on it. Make sure that no hoses are crushed in the process. • Remove the polystyrene base from the bottom. • Return appliance to it's upright position. Necessary tools 10 mm 30 mm • Remove the external film. Use a cutter, if necessary.
• Unscrew the three bolts and remove the hose holders. • Slide out the relevant plastic spacers. Warning! Do not remove the drain hose from the rear support. Remove this hose only if it is necessary to drain the water. Refer to "Frost precaution" and "What to do if". • Plug the smaller upper hole and the two large ones with the corresponding plastic plug caps. Positioning and levelling x4 Level the appliance by raising or lowering the feet. The appliance MUST be level and stable on a flat hard floor.
Water drainage Accurate levelling prevents vibration, noise and displacement of the appliance during operation. Repeat the levelling action, if the appliance is not level and stable. Warning! This appliance is free standing only. Do not remove the worktop for any reason. Firstly form a hook in the end of the drain hose using the plastic hose guide supplied with the appliance . The end of the drain hose can be positioned in four ways: • Hooked over the edge of a sink using the plastic hose guide.
MAX 100cm • Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose. The drain hose must not be kinked. • Directly to a built-in drain pipe in the room wall. The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your Local Centre. Connections overview 0.
Special accessories Rubber feet kit (4055126249) Available from your authorized dealer. The rubber feet are particularly recommended on floating, slippery and wooden floors. Mount the rubber feet to prevent vibration, noises and displacement of the appliance during operation. Read carefully the instructions supplied with the kit. First use • Ensure that the electrical and water connections comply with the installation instructions. • Ensure that the drum is empty.
Before Loading The Laundry Important! Make sure that no metal objects are left in the laundry (e.g. hair clips, safety pins, pins). Button up pillowcases, close zip fasteners, hooks and poppers. Tie any belts or long tapes. Remove any hooks (e.g curtains). • Never wash whites and coloureds together. Whites may lose their «whiteness» in the wash. • New coloured items may run in the first wash; they should therefore be washed separately the first time.
Warning! If you wish to carry out the prewash, pour the detergent for prewash phase among washing items into the drum. Warning! Depending on the type detergent you use (powder of liquid), ensure that the flap, placed in the main wash compartment, is in the desired position.
If the flap is not in the desired position: • Measure out the detergent. For the quantity of detergent, refer always to what is written on the product packing and ensure that the detergent can be poured in the drawer. • Remove the drawer. Push the drawer edge outwards where indicated by the arrow (PUSH) to facilitate drawer removal. • Pour the liquid detergent in the compartwithout exceeding the limit indicament ted in the flap.
Set your washing programme The control panel permits to select a washing programmes and different options. When an option button is selected, the corresponding pilot light is on. Otherwise it is off. For compatibility among washing programmes and options, see the "Washing Programmes". If an incorrect option is selected, the integrated red pilot light of the button 9 flashes 3 times and the display shows the message Err.
Temperature button 90° 60° 40° 2 30° Soguk Push the temperature button to select the most suitable temperature for washing your laundry . Sıcaklık Spin Reduction 1200 900 3 700 Sıkma By selecting a programme, the appliance proposes automatically the maximum spin speed provided for that programme. Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a different speed. The relevant light illuminates.
Display 7 7.1 7.2 7.3 The display shows the following information: 7.1 Delay Start icon 7.2 Child safety lock This device permits you to leave the appliance unattended during it's functioning. 7.3 • Duration of the selected programme After selecting a programme, the duration is displayed in ). The duration is calhours and minutes (for example culated automatically on the basis of the maximum recommended load for each type of fabric.
Selecting the delay start : • Select the programme and the required options. • Select the delay start by pressing button 8. • Press button 9: – the appliance starts its hourly countdown. – the programme will start after the selected delay has expired. You can cancel or modify the delay time at any moment, before you press button 9. Cancelling the Delay Start after having started the programme: • Set the appliance to PAUSE by pressing button 9. • Press button 8 once. On the display will appear '.
• To restart the programme from the point at which it was interrupted, press the button 9. • After the programme has started the door is locked. If, for any reason, you need to open the door, set firstly the appliance to PAUSE by pressing the button 9. After a few minutes it will be possible to open the door. If the door remains locked, this means that the appliance is already heating or that the water level is too high.
Door seal At the end of every cycle, check from the door seal and remove objects that could be trapped in the fold. Washing programmes Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options COTTONS 90°- Cold Main wash - Rinses - Maximum spin speed at 1200 rpm Max. load 7 kg - Reduced load 3,5 kg White, coloured cotton and linen. Normally soiled items.
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options DELICATES 40°- Cold Main wash - Rinses - Maximum spin speed at 700 rpm Max. load kg 3,5 - Reduced load 2 kg Delicate fabrics: acrylics, viscose, polyester . Normally soiled items. RINSE HOLD, SUPER QUICK 1), EXTRA RINSE, DELAY START WOOL / HANDWASH 40°- Cold Main wash - Rinses - Maximum spin speed at 1200 rpm Max.
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Detergent Compartment Options BLANKET 30° Main wash - Rinses - Maximum spin speed at 700 rpm Special programme for a single synthetic blanket, duvet, bedspread and so on. The Extra Rinse option is activated automatically. DELAY START MINI 30’ 30° Main wash - Rinses - Maximum spin speed at 700 rpm Max. load 3 kg Synthetics and delicates.
Programmes Load (kg) Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Remaining moisture (%)1) Standard cotton programmes Standard 60 °C cotton 7 1.07 50 236 53 Standard 60 °C cotton 3,5 0.79 36 192 53 Standard 40 °C cotton 3,5 0.57 36 166 53 1) At the end of spin phase. Off Mode (W) Left On Mode (W) 0.48 0.
• open the filter cover by pressing the special hook and by rotating the cover upwards; • Use a stiff brush to clean and remove all washing powder residue. • Clean all the removed parts of the dispenser drawer under a tap to remove any traces of accumulated powder. Warning! Keep the filter cover open until the filter removal.
The filter is inserted correctly when the indicator on its top is visible and blocked. • close the filter cover; • insert the mains plug again. Cleaning the water inlet filters Important! If the appliance doesn't fill, it takes a long time to fill with water, the starting button flashes red or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked . • Screw the hose back onto the tap.
Fault code and malfunction Possible cause / Solution The water tap is closed. • Open the water tap. The inlet hose is squashed or kinked. • Check the inlet hose connection. The filter in the inlet hose or the inlet valve filter are blocked. • Clean the water inlet filters (read "Cleaning the water inlet filters" for more details). Problem with the water supply The drain hose is squashed or kinked. • Check the drain hose connection. The drain filter is clogged.
Malfunction Possible cause / Solution The appliance does not start: The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no power at the socket. • Please check your domestic electrical installation. The main fuse has blown. • Replace the fuse. The programme selector dial is not correctly positioned and the button 9 has not been pressed. • Please turn the selector dial and press the button 9 again. The delay start has been selected.
Malfunction Possible cause / Solution Spinning starts late or the appliance does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed in the drum, the appliance will not spin.
www.zanussi.
www.zanussi.
www.zanussi.
192978810-A-192013 www.zanussi.
