EN User manual Washing Machine ZWG 580 P ZWG 5100 P ZWG 5120 P
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 4 5 5 6 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ 16 Consumption values _ _ _
• Install the appliance on a flat hard floor. • Never place cardboard, wood or similar materials under the appliance to compensate for any unevenness in the floor. • If the appliance is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance. • Check that the appliance does not touch the wall or other kitchen units. • This appliance must be connected to a cold water supply.
To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical. Frost precaution If the appliance is installed in a place where the temperature could drop below 0°C, proceed as follows to remove any water remaining inside the appliance: 1. unplug the appliance; 2. turn off the water tap; 3.
This means that they can be recycled by disposing of them properly in appropriate collection containers. Ecological hints To save water, energy and to help protect the environment, we recommend that you follow these tips: • Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!). • The machine works more economically if it is fully loaded.
Water supply pressure Minimum Maximum 0,05 MPa 0,8 MPa Maximum Load Cotton 6 kg Spin Speed Maximum 1200 rpm (ZWG 5120 P) 1000 rpm (ZWG 5100 P) 800 rpm (ZWG 580 P) Installation Unpacking Warning! • Read carefully the "Safety information" chapter before installing the appliance. x3 A B • Remove the cardboard top. • Remove the polystyrene packaging materials.
• Remove the power supply cable and the draining and inlet hose from the hose holders ( C ) on the rear of the appliance. • Plug the smaller upper hole and the two large ones with the corresponding plastic plug caps. Positioning and levelling • Unscrew the three bolts ( A ) and remove the hose holders ( C ). • Slide out the relevant plastic spacers ( B ). Level the appliance by raising or lowering the feet.
Firstly form a hook in the end of the drain hose using the plastic hose guide supplied with the appliance . The end of the drain hose can be positioned in four ways: • Hooked over the edge of a sink using the plastic hose guide. Accurate levelling prevents vibration, noise and displacement of the appliance during operation. Repeat the levelling action, if the appliance is not level and stable. Water inlet Connect the hose to a tap with a 3/4” thread.
The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your Local Centre. Connections overview 115 cm 100 cm Electrical connection • The appliance must be earthed. • Make sure that the electrical information on the rating plate agree with your domestic power supply. • Always use a correctly installed shockproof socket. • Do not use multi-way plugs, connectors and extension cables. There is a risk of fire.
Daily use Sort out the laundry Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. Before Loading The Laundry Important! Make sure that no metal objects are left in the laundry (e.g. hair clips, safety pins, pins). Button up pillowcases, close zip fasteners, hooks and poppers. Tie any belts or long tapes. Remove any hooks (e.g curtains). • Never wash whites and coloureds together.
Open the detergent dispenser drawer Compartment for powder or liquid detergent used for main Compartment wash. for liquid additives (fabric softener, starch). Detergents and additives The type and quantity of detergent will depend on the type of fabric, load size, degree of soiling and hardness of the water used. For the quantity of detergent, refer always to what is written on the product packing.
• Remove the drawer. Push the drawer edge outwards where indicated by the arrow (PUSH) to facilitate drawer removal. The flap is down and you wish to use powder detergent: • Rotate the flap upwards. Ensure to fit the flap completely in. • Carefully put the drawer back. • Measure out the detergent. • Pour the powder detergent into the main wash compart. ment The flap is up and you wish to use liquid detergent: • Rotate the flap downwards. • Carefully put the drawer back. • Measure out the detergent.
7.1 7.2 7.3 1 2 3 4 5 6 Turn the programme selector dial to the required programme. The selector dial can be turned either clockwise or counter-clockwise. The green pilot light of the button 6 starts flashing: the appliance is now switched on. Programme selector dial 1 If you turn the programme selector dial to another programme when the appliance is working, the red pilot light of the button 6 will flash 3 times to indicate a wrong selection.
3 - Spin Reduction Spin reduction and Rinse Hold By selecting a programme, the appliance proposes automatically the maxoption imum spin speed provided for that programme. 1200 Press this button repeatedly to change the spin speed, if you want your 900 laundry to be spun at a different speed. The relevant light illuminates. 700 Rinse Hold By selecting this function the water of the last rinse is not emptied out to prevent the fabrics from creasing.
Extra Rinse 4h 8h Start/Pause 6 Indicator pilot lights 7.1 7.2 7.3 This appliance is designed for saving water. However, for people with very delicate skin (allergic to detergents) it may be necessary to rinse the laundry using an extra quantity of water. Press simultaneously the buttons 4 and 5 for some seconds: the pilot light 7.2 comes on. This function stays permanently on. To remove it press the same buttons again until the pilot light 7.2 goes off.
• Turn the programme selector dial to . • Select the draining or spinning programme. • Reduce the spin speed if needed, by pressing the relevant button. • Press the button 6 . At the end of the programme, the door can be now opened. Turn the programme selector dial to to switch the appliance off. Remove the laundry from the drum and carefully check that the drum is empty. If you do not intend to carry out another wash, close the water tap.
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load Type of Laundry Options COTTON ECONOMY 60° - 40° Main wash - Rinses - Maximum spin speed 1200 / 1000 / 800 rpm1) Max. load 6 kg White and coloured cotton . This programme can be selected for slightly or normally soiled cotton items. The temperature will decrease and the washing time will be extended. This allows to obtain a good washing efficiency by saving energy.
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load Type of Laundry RINSE Rinse - Short spin speed 700 rpm. If a spin speed higher than 700 rpm is selected, by pressing the relevant button, the appliance performs a long spin. (Maximum spin speed at 1200 / 1000 / 800 rpm1)) Max. load 6 kg To rinse and spin cotton garments which have been washed by hand. Select the EXTRA RINSE option to intensify the rinsing action. The appliance adds additional rinses.
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load Type of Laundry JEANS (Cold) 60°Main wash - Rinses - Maximum spin speed 1200 / 1000 / 800 rpm1) Max. load 3 kg Trousers, shirts or jackets in denim and jersey realized with hitech materials. The Extra Rinse option is activated automatically. Detergent Compartment Options SPIN REDUCTION, RINSE HOLD, DELAY START 1) Depending on a model.
The pump must be cleaned regularly. To clean the filter, proceed as follows: • turn programme selector dial to position ; • unplug the appliance; • open the door; • Remove the drawer. • To aid cleaning, the top part of the additive compartment should be removed. • turn the drum and align the filter cover ( FILTER ) with the arrow on the door seal; • open the filter cover by pressing the special hook and by rotating the cover upwards; Warning! Keep the filter cover open until the filter removal.
• if necessary, place the filter cover in the right position again. • open the filter cover and insert the filter again; Cleaning the water inlet filters Important! If the appliance doesn't fill, it takes a long time to fill with water, the starting button flashes red or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked . To clean the water inlet filters: • Turn off the water tap.
Fault code and malfunction Possible cause / Solution The water tap is closed. • Open the water tap. The inlet hose is squashed or kinked. • Check the inlet hose connection. The filter in the inlet hose or the inlet valve filter are blocked. • Clean the water inlet filters (read "Cleaning the water inlet filters" for more details). The light of button 6 flashes and the light 7.1 illuminates: Problem with the water supply The drain hose is squashed or kinked. • Check the drain hose connection.
The appliance does not start or stops during operation without any visible alarm. Malfunction Before contacting your local Service Centre, please carry out the checks listed below. Possible cause / Solution The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no power at the socket. • Please check your domestic electrical installation. The main fuse has blown. The appliance does not start: • Replace the fuse.
Malfunction Possible cause / Solution The transit bolts and packing have not been removed. • Check the correct installation of the appliance. The appliance is not levelled correctly. The appliance vibrates noisi- • Adjust the feet. The laundry is not evenly distributed in the drum. ly: • Redistribute the laundry. Maybe there is very little laundry in the drum. • Load more laundry. The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum.
Mod Prod . ... . No. ... ... ... ... .. Ser. No. ... ... ... The necessary data for the service centre is on the rating plate. We recommend that you write the data here: Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... ... ... Model description (MOD.) ............................... Product number (PNC) ............................... Serial number (S.N.) ...............................
192991760-A-292010 www.zanussi.