EN User manual Washing machine ZWG2120 P 147214310
EN Contents Safety information ..................................... 2 Control panel............................................. 11 Environment concerns............................... 4 Set your washing program......................... 12 Product description................................... 5 International wash code symbols................ 15 Technical data........................................... 5 Programs informations............................... 16 Installation.........................
Installation This appliance is heavy. Care should be taken when moving it. When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre. All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in the user manual.
Environment concerns Packaging materials The materials marked with the symbol recyclable. are >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers. Old machine Use authorised disposal sites for your old appliance. Help to keep your country tidy! The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Product description 1 2 3 6 4 7 8 10 9 5 11 Front View Back View 1 Detergent Dispenser Drawer 5 Front Feet 9 2 Worktop 6 Water Inlet Hose 10 Hose Holders 3 Control Panel 7 Drain Hose Support 11 Back Feet 4 Door Opening Handle 8 Mains Cable Water Drain Hose Technical data Dimensions Power supply voltage/frequency Total power absorbed Minimum fuse protection Water supply pressure Maximum Load Spin Speed Width Height Depth Minimum Maximum Cottons Synthetics Delicates Hand Wash Model :
Installation Unpacking Important! All transit bolts and packing must be removed before using the appliance. Remove the polystyrene base, set the machine upright and unscrew the remaining rear screw. Slide out the relevant pin. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. Using a spanner unscrew and remove the two rear bottom screws.
Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or cupboard units. Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor.
Electrical Connection This machine is designed to operate on a 220-240 V, single-phase, 50 Hz supply. “An incorrect power supply may void your warranty.” Check that your domestic electrical installation can take the maximum load required (2.0 kW), also taking into account any other appliances in use. Important! Connect the machine to an earthed socket. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution.
Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole. Mould stains: treat with bleach, rinse well (whites and fast coloureds only). Grass: soap lightly and treat with bleach (whites and fast coloureds only). Ball point pen and glue: moisten with acetone (*), lay the garment on a soft cloth and dab the stain.
Do not spray stain pre-treatment products (e.g. Vanish) on or near the machine, as it can attack plastic materials reducing its life. Quantity of detergent to be used Compartment : this compartment is used for washing powder or liquid. Compartment : this compartment is used for fabric conditioner and starching agent. The type and quantity of detergent will depend on the type of fabric, load size, degree of soiling and hardness of the water used.
Clip the flap down if you are going to use liquid detergent. Refit the dispenser back into its runners. Remember: If you change the type of detergent you use, the position of the flap will need changing. If you wish to carry out the “prewash” phase, pour it into the compartment marked “ ”. If required, pour fabric softener into the compartment marked (the amount used must not exceed the “MAX” mark in the drawer). You are now ready to add detergent.
Set your washing program Program selector dial Turn the program selector dial to the required program. The green Start/Pause light starts to flash. The selector dial is divided into following sections: (Cancelling/Off) Rinse Cottons Drain Prewash Spin Economy Easy Iron Synthetics 5 Shirts Mixed Fabric Mini 30 Delicates Jeans Wool/Handwash * for more programs information see page 16. The selector dial can be turned either clockwise or anticlockwise.
Spin Buttons Press the Spin button repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washing machine. The relevant light will light up. Rinse Hold ( ): by selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing.
Important! The selected delay can be changed only after selecting the washing program again. The door will be locked throughout the delay time. If you need to open the door, you must first set the washing machine to PAUSE by pressing the Start/Pause button and then wait about 3 minutes. After you have closed the door, press the Start/Pause button again. Extra Rinse Option ( ) This option is recommended for people who are allergic to detergents, and in areas where the water is very soft.
Altering an option or a running program It is possible to change any option before the program carries it out. The option “Super Quick” cannot be modified after the Start/Pause has been pressed. Changing a running program is possible only by resetting it. Turn the program selector dial to “O” and then to the new program position. The washing water in the tub not be emptied out. Start the new program by depressing the “Start/Pause” button again.
Programs informations To reset a programme and to switch off the machine turn the selector dial (Cancelling/Off) to “O”. Now, a new programme can be selected. Cottons Washing programme for white and coloured cottons fabrics. Cottons Prewash select this program if you wish your laundry to be prewashed at 30° C before the main wash. select this program if you wish your laundry to be washed is slightly/ normally soiled cottons. This program will obtain good washing results whilst saving energy.
Washing programs Program/ Temperature Type of laundry Options Max. Load White, coloured cotton and linen (Normally Cold - 90° C soiled items).: e.g. shirts, underwear, towels. Main wash at Cold - 90° C Rinses Long spin - Spin Reduction - Rinse Hold ( ) - Delay Start - Super Quick - Extra Rinse ( ) 6.0 kg White, coloured cotton and linen (Heavy soiled Prewash items).: e.g. sheets, Cold - 90° C tablecloths, household linen.
Program/ Temperature Type of laundry Options Max. Load Drain For emptying out the water left in the drum. Drain of water Not available 6.0 kg Spin Separate spin program for spin out the water from clothes. Drain Long spin - Spin Reduction - Delay Start 6.0 kg Cottons and synthetic or mixed fabrics. Main wash at Cold - 40° C Rinses Short spin - Spin Reduction (Maximum 900 rpm.) - Rinse Hold ( ) - Delay Start - Extra Rinse ( ) 2.
To run a maintenance wash: The drum should be empty of laundry. use a small brush to clean the recess. Select the hottest cotton wash program. Use a normal measure of detergent, must be a powder with biological properties. External cleaning Clean the exterior cabinet of the appliance with soap and water only, and then dry thoroughly. Cleaning the dispenser drawer The washing powder and additive dispenser drawer should be cleaned regularly.
Something not working Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below. During machine operation it is possible that the red Start/Pause pilot light flashes to indicate that the machine is not working. Once the problem has been eliminated, press the Start/Pause button to restart the program.
Malfunction There is water on the floor: Unsatisfactory washing results: The door will not open: The machine vibrates or is noisy: Possible cause Solution Too much detergent or unsuitable detergent (creates too much foam) has been used. Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp. Check the water inlet hose connection.
Malfunction Spinning starts late or the machine does not spin: No water is visible in the drum: Possible cause Solution The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed in the drum, the machine will not spin.
122010 www.zanussi.
