REFRIGERATOR ZU 9155 INSTRUCTION BOOKLET 2222681-36
CONTENTS Instructions for the User Instructions for the Installer Important Safety Instructions 3 Technical Specifications 13 Description of the Appliance 4 Installation 13 Operation 5 Before use Setting the temperature Fresh food refrigeration The door shelves Normal Operating Sounds 5 5 5 5 5 Health and Safety Guidelines 6 Defrosting 7 Maintenance and Cleaning 7 Internal cleaning External cleaning Periodic cleaning Changing the light bulb When the appliance is not in use 7 7 7 8 8 So
IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation ■ General Safety Check the appliance for transport damage. Under no circumstance should a damaged appliance be installed. In the event of damage please contact your retailer.
DESCRIPTION OF THE APPLIANCE A B C D - Dairy compartment - Movable shelf - Bottle storage shelf - Airduct exit E - Air inlet filter F - Salad bins G - Storage shelves H - Thermostat control 4
OPERATION Before use Butter & cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible. Milk bottles: these should have a cap and should be stored in the bottle rack on the door. Remove all securing tapes. Wash inside the appliance with lukewarm water and bicarbonate of soda (5 ml to 0.5 litre of water). Do not use soap or detergent as the smell may linger. Dry thoroughly.
Normal Operating Sounds You may hear faint gurgling or bubbling sounds when the refrigerant is pumped through the coils below, to the cooling evaporator. When the compressor is on, the refrigerant is being pumped round, and you will hear a whirring sound or pulsating noise from the compressor. A thermostat controls the compressor, and you will hear a faint ‘click’ when the thermostat cuts in and out.
DEFROSTING The refrigerator automatically defrosts every time the compressor stops. The water is discharged, via the pipe, into a tray located at the back of the appliance above the compressor, where it evaporates. Important To avoid defrost water overflowing and collecting beneath the salad bins, periodically clean the water discharge hole (F) situated under the vegetable drawers. Use the special cleaner provided (P) which you will find already inserted into the discharge hole P F S.I.
Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: 1. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest Zanussi Service Force centre). 2. Replace the light cover by sliding it into its original position and replacing the screw.
SERVICE AND SPARE PARTS Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not Working’. When you contact the Service Centre you will need to give the following details. In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Zanussi Service Force Centre by telephoning:- 08705 929929 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of the fault 4.
To contact your local Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 Vale, Guernsey Channel Islands GY1 3AD JERSEY Jersey Electricity Company Haut De L’orme Rue De Haut De L’orme Trinity Jersey Channel Islands JE3 5FG SCOTLAND ABERDEEN 54 Claremont Street Aberdeen AB10 6RA AUCHTERMUCHTY 33a Burnside Auchtermuchty Fife KY14 7AJ ISLE OF LEWIS KELSO 2, 6 & 8 Woodmarket Kelso Borders TD5 7AX ORKNEY 7 King Street Kirkwall Orkney KW15 1JF PERTH (O
To contact your local Service Force Centre telephone 08705 929 929 MIDLANDS BIRMINGHAM 66 Birch Road East Wyrley Trading Estate Witton Birmingham B6 7DB BOURNE Pinfold Road Bourne PE10 9HT BRIDGNORTH 68 St.
GUARANTEE CONDITIONS Standard guarantee conditions We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: ■ The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
TECHNICAL SPECIFICATIONS DIMENSIONS Height Width Depth 81,5 56 53,8 POWER SUPPLY VOLTAGE AND FREQUENCY TOTAL POWER ABSORBED AVERAGE DAILY UNITS ELECTRICITY (*) 220-240 V / 50 Hz 70 W 0,50 kWh GROSS CAPACITY 138 l NET CAPACITY 135 l cm cm cm (*)This figure is based on standard test results in accordance with European Standard EN153. Actual consumption will depend on how the appliance is used and where it is located.
ELECTRICAL CONNECTION WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted. This appliance complies with the following E.E.C. Directive: - 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent amendments. - 89/336 EEC of 3.5.
BUILDING-IN INSTRUCTIONS Before carrying out any work, remove the plug from the power socket. a Grid preparation Remove the grid from the appliance pulling it towards you with hands. a Right door opening: Remove the left side (A) of the grid cutting it from the rear (see figure, a). S.I.001 Left door opening: Remove the right side (B) of the grid cutting it from the rear (see figure, b).
Building the appliance in under a worktop The dimensions of the recessed installation area must correspond with those indicated in the figure. The appliance could be inserted between two units (a) or as an end unit (b). 60 0 min 820 - 870 55 0 a 600 b S.I.004 The plug socket necessary for connection of the appliance to the electricity supply should be positioned, so that the plug is not placed in the recess. S.I.005 Fasten the side panel to the rear of the appliance with the fixing brackets.
The appliance is equipped with adjustable support feet. To adapt the appliance to the height of the installation area (max 870 mm), screw in, or screw out the feet situated at each bottom corner. 30 S.I.006 Separate parts A, B, C, D as shown in the figure. B A C D PR266 50mm Place guide (A) on the inside part of the furniture door, in the upper and lower positions as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied.
Should adjustment of the furniture door be necessary, use the clearance of slots. At the end of operations, it is necessary to check if the door of the furniture closes properly. PR168 Push cover (D) into guide (B) until it clips into place. B D PR167/1 Fitting the plinth Important For the efficient operation of the appliance, it is important that the original ventilation grid is used. S.I.007 ■ 580 25 25 S.I.
© Electrolux Household Appliances Limited 2000
