Contents Installation Unpacking Positioning & leveling Water connection Electrical connection Operation Controls description Loading the clothes Filling with washing powder Use of additive Which powder Selection of washing programmer Starting Stopping Wash cycle Care and cleaning Cleaning the machine Cleaning the drain collector Hints for care of washing powder dispenser Helpful tips for washing Servicing Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 12 Technical
Installation Unpacking After removing outer carton, reinforcing angles and polythene wrapping, processed as follows: 1. tilt machine backwards, undo and remove the two screws located on the bottom of the appearance (Fig. 1); recover the relevant rubber washers and spacers; 2. remove the two cardboard strips {A Fig. 1} undo and remove the two resews located on the back of the appliance (Fig. 2); 3.
Water connection The machine may either be thumbed in or connected to existing taps. Details are given below, Water supply Separate supplies of hot and cold water are necessary. Single cutlet gas or electric heaters are not suitable. If only cold water supp: available, connect the two hoses to a cold water tap. Note:The cold water fill hose and the drain hose are supplied separately, under the lid of the washer, and must be connected upon installation of the machine by gong through a few simple steps.
1t is therefore, advisable that the drain pipe. if used, has an internal diameter of at least 4 eme {15 inning. Also, ensure that the drain hose i chocked or placed in such u way obstruct the normal water flow. If the drain hose is to be hooked over the sink, ensure that the sink is empty and that the sink plug is not blocking the plug hole.
After settling the inlet hoses as desired, be sure to tighten their ring nuts again to prevent leakages, If the water supply is from new pi from pipes which have not been a long time, it is a certain amount of water before connecting the machine. This will avid foreign matter blocking the filters.
Operating instructions 1] OS Controls description 1 Cold wash push button 21: by pressing in this push button prior to selecting & wash eyelet, the programmer will be carried out with cold water only. A cold water programmer is particularly suitable to wash very delicate synthetic fabrics, curtains, and drapes 2 Spin push button «8G0x»: if pressed in at the beginning of an energetic wash cycle, this push button provides the final spin at 800 rpm. instead of 400 r.p.m.
Loading the clothes Lift the lid on the machine and turn the drum by hand until the loading door appears (Fig. 101 Push safety lever A (Fig. 10} to the right and press it down until flap door € (Fig. 10} disengages. Fasten drum {lap door B into the spec for the purpose, and then place the clothes in the drum taking ware to spread them out evenly. Close the loading door by overlapping flap C on flap B, making sure tha lever A returns to its original position.
These products’ balanced lather are specially designed to complement the leaning action of these machines, 3o use it regularly for trouble free washing and superb results. punt, of powder i grams at fll load To owe | Darwin | Voo o rescind | sadhu o preach Soft: Average: 1225 0 145 170 Hard: 95 260 3 Very b 55 220 210 For hardness in p.pm multiply indicated hardness value by 10. For information regarding the degree of hardness in your area, enquirer at your local water authority.
Gentle wash cycles For Delicate, Syntheses, Mixed Fabrics and Woolens Recommended wash load: max. 3-5 Ibs (15-2 Kg; wool max. 2 Ths (1 Kg). {important: There is no water draining in the last rinse of the gentle wash cycles, to prevent the clothes from creasing if they are left in the machine at the end of the wi sh cycle. To drain the water, turn the programmer selector knob to eyelet «U» (draining & gentle spinning) or cycle «V» (draining without spinning).
Care and cleaning Cleaning the machine Important: Make sure that the plug has been removed from the socket prior to undertaking any kind of maintenance. From time to time, carry out a complete cycle without & washing load, adding 1 oz of «Calgary.
Pen the flap door of the filter compartment by pressing it inwards with . finger at the hinged side (as shown in Yig. 18). thrift safety slider A (Fig. 13) until the ed notch B (Fig. 13) disappears. Urn the filter knob counterclockwise ad pull the filter out (Fig. 14). Sean filter thoroughly. Refit the filter and turn the knob dock wise until the red notch reappears.
Washing powder should only be placed in the dispenser immediately prior to the start of a programmer. Do not leave washing powder in the dispenser for any length of time as it may form lumps which can be difficult to dissolve. 1t is advisable to inspect the filters in the water inlet hoses periodically and clean if necessary.
GAUSSIAN APPLIANCE GUARANTEE GAUSSIAN STANDARD GUARANTEE CONDITIONS This guarantee Is in addition to your statutory and other loyal rights which will not be excluded or in any way diminished by the return of the guarantee card, We, 1AZ International {UK) Lid, undertake that if, within twelve months (24 months for TV sets) of the date of the purchase, this GAUSSIAN appliance or any part thereat is proved to be defective by reason only of faulty workmanship or materials, we will, sd our option, repair ng repl