EN User manual ZRA33400WA
Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 4 5 5 5 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
nents of the refrigerant circuit become damaged. If the refrigerant circuit should become damaged: – avoid open flames and sources of ignition – thoroughly ventilate the room in which the appliance is situated • It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short-circuit, fire and/or electric shock.
• This product must be serviced by an authorized Service Centre, and only genuine spare parts must be used. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local authorities.
Temperature regulation The temperature is automatically regulated. To operate the appliance, proceed as follows: • turn the Temperature regulator toward lower settings to obtain the minimum coldness. • turn the Temperature regulator toward higher settings to obtain the maximum coldness. A medium setting is generally the most suitable.
Hints for energy saving • Do not open the door frequently or leave it open longer than absolutely necessary. • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.
It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside. Troubleshooting Caution! Before troubleshooting, disconnect the power supply. Only a qualified electrician or competent person must do the troubleshooting that is not in this manual. Problem Important! There are some sounds during normal use (compressor, refrigerant circulation).
Problem Possible cause Solution The Temperature regulator may be set incorrectly. Set a higher temperature. The temperature in the appliance is too low. The Temperature regulator may be set incorrectly. Set a higher temperature. The temperature in the appliance is too high. The Temperature regulator may be set incorrectly. Set a lower temperature. The door is not closed correctly. Refer to "Closing the door". The product temperature is too high.
Technical data Dimension Height 1540 mm Width 595 mm Depth 658 mm Voltage 230 - 240 V Frequency 50 Hz The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label.
not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician. The manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with the E.E.C. Directives. Rear spacers You can find the two spacers in the bag with documentation. Do these steps to install the spacers: 1. Release the screw. 2. Engage the spacer below the screw. 3. Turn the spacer to the right position. 4.
• Unscrew the handle (1) and fix it on the opposite side (2). • Re-insert the cover pins (3) on the opposite side. 1 7 3 2 6 8 • Unscrew the upper pin (4) and screw it on the opposite side. (5) • Refit the door. • Refit and screw both lower hinges. • Refit the plinth (8). 5 4 Do a final check to make sure that: • All screws are tightened. • The edges of the doors run parallel to the side edge of the appliance. • The magnetic seal adheres to the cabinet. • The door opens and closes correctly.
280151517-A-062013 www.zanussi.
