EN User manual Refrigerator ZRA33400WA
Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 4 5 5 5 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
nents of the refrigerant circuit become damaged. If the refrigerant circuit should become damaged: – avoid open flames and sources of ignition – thoroughly ventilate the room in which the appliance is situated • It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short-circuit, fire and/or electric shock.
• This product must be serviced by an authorized Service Centre, and only genuine spare parts must be used. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the applicable regulations to obtain from your local authorities.
To operate the appliance, proceed as follows: • turn the Temperature regulator toward lower settings to obtain the minimum coldness. • turn the Temperature regulator toward higher settings to obtain the maximum coldness. A medium setting is generally the most suitable. However, the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on: • room temperature • how often the door is opened • the quantity of food stored • the location of the appliance.
• If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.
It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside. Troubleshooting Caution! Before troubleshooting, disconnect the power supply. Only a qualified electrician or competent person must do the troubleshooting that is not in this manual. Problem Important! There are some sounds during normal use (compressor, refrigerant circulation).
Problem Possible cause Solution The Temperature regulator may be set incorrectly. Set a higher temperature. The temperature in the appliance is too low. The Temperature regulator may be set incorrectly. Set a higher temperature. The temperature in the appliance is too high. The Temperature regulator may be set incorrectly. Set a lower temperature. The door is not closed correctly. Refer to "Closing the door". The product temperature is too high.
Technical data Dimension Height 1544 mm Width 595 mm Depth 658 mm Voltage 230 - 240 V Frequency 50 Hz The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label.
Warning! This appliance must be earthed. The manufacturer declines any liability should these safety measures not be observed. A B 5. Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. 6. Switch on the appliance. The appliance is supplied with a 13 amp plug fitted B. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used.
7 Door reversibility Important! To carry out the following operations, we suggest that this be made with another person that will keep a firm hold on the doors of the appliance during the operations. To change the opening direction of the door, do these steps: • Remove the plug from the power socket. • Tilt back the appliance carefully so that the compressor cannot touch the floor. • Remove the plinth (1). • Remove the cap (2) and position it on the opposite side.
• The edges of the doors run parallel to the side edge of the appliance. • The magnetic seal adheres to the cabinet. • The door opens and closes correctly. It is advisable to wait at least four hours before connecting the appliance to allow the oil to flow back in the compressor. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabi- net. In that case, wait for the natural fitting of the gasket.
www.zanussi.
www.zanussi.
www.zanussi.
280151037-B-512012 www.zanussi.
