User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • • Before carrying out any maintenance, disconnect the appliance from the power supply. Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock. Do not use a steam cleaner to clean the appliance. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the glass door since they can scratch the surface, which may result in shattering of the glass.
• • • Use only correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors. The electrical installation must have an isolation device which lets you disconnect the appliance from the mains at all poles. The isolation device must have a contact opening width of minimum 3 mm. This appliance complies with the E.E.C. Directives. GAS CONNECTION • All gas connections must be made by a qualified person.
• • If you use an oven spray, follow the safety instruction on it's packaging. Do not clean the catalytic enamel (if applicable) with any kind of detergent. • DISPOSAL WARNING! Risk of injury or suffocation. INTERNAL LIGHTING WARNING! Risk of electric shock. • • • • The type of light bulb or halogen lamp used for this appliance is for household appliances only. Do not use it for house lighting. Before replacing the lamp, disconnect the appliance from the power supply.
burner area, as shown in "Product description" chapter. INITIAL CLEANING Remove all accessories and removable shelf supports from the oven. Refer to "Care and cleaning" chapter. Clean the oven and the accessories before first use. Put the accessories and the removable shelf supports back to their initial position. PREHEATING Preheat the empty appliance before first use. 1. Set the maximum temperature. 2. Let the appliance operate for 1 hour. 3. Set the function . 4.
OVEN FUNCTIONS Oven function Application The oven is off. Off position To turn on the lamp without a cooking function. Light To roast larger pieces of meat on the turnspit. Turnspit USING THE GRILL Oven safety device: The gas oven has a thermocouple. It stops the gas flow if the flame goes out. 1. Press the knob for the gas control and turn it to . Keep the knob for the gas control pushed for 15 seconds or less. Do not release the knob until the flame ignites. 2. Release the knob for the gas control.
A. B. C. D. 1. 2. 3. Turnspit frame Forks Spit Handle Put the turnspit handle into the spit. Put the deep pan on the lowest shelf position. Put the spit frame on the third shelf position from the bottom. Baking tray: Push the baking tray between the guide bars of the shelf support. 4. Install the first fork on the spit, then put the meat on the turnspit and install the second fork.
ADDITIONAL FUNCTIONS COOLING FAN When the oven operates, the cooling fan turns on automatically to keep the surfaces of the oven cool. If you turn off the oven, the cooling fan can continues to operate until the oven cools down. HINTS AND TIPS WARNING! Refer to Safety chapters. The temperature and baking times in the tables are guidelines only. They depend on the recipes and the quality and quantity of the ingredients used. COOKING RECOMMENDATIONS The oven has five shelf positions.
Temperature Time (min) (°C) Food Goat meat, 1.8 kg 170 - 180 60 - 90 Pizza Preheat the empty oven before cooking. Prepare 1.4 - 1.5 kg of food. Use the third or fourth shelf position. Food Temperature (°C) Food Temperature Time (min) (°C) Time (min) Bone-in beef, 1.0 kg min. 50 - 65 Pizza, thin 200 - 210 20 - 30 Boneless beef, 1.0 kg 190 55 - 65 Pizza, thick 200 - 210 25 - 30 Lamb, 1.0 kg min. 50 - 65 Calzone 190 - 200 25 - 30 Chicken / Rabbit, 1.2 kg 220 - 230 85 - 95 Duck, 1.
Food TemperaTime (min) ture (°C) Fruit pie in a 26 cm round cake mould on the wire shelf min. 50 - 60 Choux pastry 190 35 - 45 Vol au vent 170 25 - 35 Jam tart in a 30 cm round cake mould on the wire shelf 165 50 - 60 Egg Custard in a bain-marie TemperaTime (min) ture (°C) min. 70 - 85 Cakes Preheat the empty oven for 10 minutes before cooking. Use the aluminium baking tray if no other cookware specified below. Use the fourth shelf position. Food Ginger bread min.
Use the turnspit with the bottom oven burner. Use the third shelf position. Time (min) Food Pieces 1st side TemperaTime (min) ture (°C) Toasted sandwiches 4-6 5-7 - Poultry, 1.0 - 1.2 kg 190 200 75 - 85 Toast 4-6 2-4 2-3 Roasts, 0.8 - 1.0 kg 190 200 75 - 85 TURNSPIT Preheat the empty oven for 10 minutes before cooking. 12 Food 2nd side INFORMATION FOR TEST INSTITUTES Tests according to IEC 60350-1.
Food Beef burger 6 pieces, 0.6 kg Function Grilling Accesso- Shelf ries position Wire shelf and dripping pan 4 Temperature (°C) max. Time (min) Comments 20 - 30 Put the wire shelf on the fourth level and the dripping pan on the third level of the oven. Turn the food halfway through the cooking time. Preheat the oven for 3 minutes. CARE AND CLEANING WARNING! Refer to Safety chapters. NOTES ON CLEANING Clean the front of the oven with a soft cloth with warm water and a mild cleaning agent.
REMOVING AND INSTALLING DOOR The oven door has two glass panels. You can remove the oven door and the internal glass panel to clean it. Read the whole "Removing and installing door" instruction before you remove the glass panels. The oven door may close if you try to remove the internal glass panel before you remove the oven door. CAUTION! Do not use the oven without the internal glass panel. 1. Open the door fully and hold both hinges. 4. Put the door on a soft cloth on a stable surface. 5.
A 2. Disconnect the oven from the mains. 3. Put a cloth on the bottom of the cavity. CAUTION! Always hold the halogen lamp with a cloth to prevent grease residue from burning on the lamp. The back lamp 1. Turn the lamp glass cover to remove it. 2. Clean the glass cover. 3. Replace the lamp with a suitable 300 °C heatresistant lamp. 4. Install the glass cover. REPLACING THE LAMP WARNING! Risk of electric shock. The lamp can be hot. 1. Turn off the oven. Wait until the oven is cooled down.
Problem Possible cause The turnspit does not rotate. Remedy The turnspit is not correctly installed into the turnspit hole. SERVICE DATA If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. The necessary data for the service centre is on the rating plate. The rating plate is on the front frame of Refer to "Using the accessories" chapter, Using the turnspit. the oven cavity. Do not remove the rating plate from the oven cavity.
3. Seal the connection correctly. Use a leak detection to control it. ADJUSTMENT TO DIFFERENT TYPES OF GAS OVEN INJECTOR REPLACEMENT 1. Remove the bottom plate of the oven cavity (A) to get access to the oven burner (B). B Only a qualified technician is authorized to handle adjustment of different types of gas. A The oven is set for natural gas, you can change it to liquid gas, with the correct injectors. The gas rate is adjusted to suit.
5. Release the burner injector (D) with a 7 mm socket spanner and replace it with a different one, which is necessary for the type of gas you use. Refer to “Technical data” chapter. 6. Assemble the burner in a reverse sequence. Replace the gas type sticker near the gas supply ramp with the one related to the new gas type. The gas oven burner does not need any primary gas regulation. Make sure that the gas supply pressure of the appliance is in line with the recommended values.
min. 4mm 548 80 21 min. 550 60 520 110 114 18 600 min. 560 589 594 65cm² 130cm² 595±1 198 60 5 3 523 20 50 548 70 21 min. 550 60 520 110 590 114 18 110 min. 560 589 594 60 595±1 5 3 20 198 65cm² 130cm² 523 There must be a clearance of minimum 4 mm between the top surface of the appliance and the inner top of the cabinet. When you install the appliance "built-under" (below a hob), install the hob before the oven unit.
When you install a hob above the oven, make different electrical connections for the hob and for the oven. Only make connections with correct cables for the power supplied. Make sure that after the installation there is easy access to the appliance if repairs or maintenance are necessary. This appliance is supplied only with a main cable. CABLE Cable types applicable for installation or replacement: H05 V2V2-F (T90), H05 BB-F For the section of the cable refer to the total power on the rating plate.
GAS OVEN BURNER Gas type NOMINAL GAS POWER (kW) NOMINAL GAS FLOW (g/h) Reduced gas power (kW) BY-PASS INJECTOR NEEDLE MARK (1/100 (1/100 mm) mm) G20 (2H) 20 mbar 2.6 - 0.7 Reg. G30/G31 30/30 mbar 2.7 196 0.7 43 80 GAS GRILL BURNER Gas type NOMINAL GAS POWER (kW) NOMINAL GAS FLOW (g/h) Reduced gas power (kW) BY-PASS INJECTOR NEEDLE MARK (1/100 (1/100 mm) mm) G20 (2H) 20 mbar 1.85 - - - 92 G30/G31 (3B/P) 30/30 mbar 2.
867348252-B-362018 WWW.ZANUSSI.