EN User manual Washer Dryer ZKG 2145
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Special accessories for installation _ _ _ _ _ 6 Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ 8 Consumption values _ _ _ _ _ _ _ _ _ _ _ _ 10 Automatic Drying programmes _ _ _ _ _ _ _ 11 Timed Drying Programmes _ _ _ _ _ _ _ _ _ 11 Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 11 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13 Personalisation _ _ _ _
• Do not change the specification of this appliance. • Obey the maximum load volume of 6 kg (refer to the “Programme chart” chapter). • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. Use • • • • • Warning! Risk of injury, electrical shock, fire, burns or damage to the appliance.
Service • Contact the Service to repair the appliance. We recommend only the use of original spare parts. Product description 1 Detergent dispenser drawer 2 Control panel 1 2 3 Door opening handle 4 Rating plate 5 Drain pump 6 Adjustable feet 3 4 5 6 Detergent dispenser drawer Compartment for detergent used for prewash and soak phase or for stain remover used during the stain action phase (if available). The prewash and soak detergent is added at the beginning of the wash programme.
Child Safety device Make sure that children or pets do not climb into the drum. To prevent children and pets becoming trapped inside the drum this machine incorporates a special feature. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical.
Super Quick Short cycle for lightly soiled items or for laundry which needs only freshening up. We recommend you to reduce the fabrics loading. Extra Rinse This appliance is designed to save energy. If it necessary to rinse the laundry using an extra quantity of water (extra rinse), select this option. Some additional rinses will be performed. This option is recommended for people who are allergic to detergents, and in areas where the water is very soft.
• Alarm codes In the event of operating problems, some alarm codes can be displayed, for example (see paragraph «What to do if...»). • Incorrect option selection If an option which is not compatible with the set wash programme is selected, the message Err is displayed at the bottom of the display for a few seconds and the integrated red light of button 7 start flashing.
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Syntetiske stoffer (Synthetics) 60° - 40° - 30°- cold Main wash - Rinses Maximum spin speed at 900 rpm Max. load 3 kg - Reduced load 1.5 kg1) Synthetic or mixed fabrics: underwear, coloured garments, non-shrink shirts, blouses. SPIN RINSE HOLD SUPER QUICK EXTRA RINSE Strygelet (Easy iron) 40° Main wash - Rinses Maximum spin speed at 900 rpm Max.
Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Rinses Maximum spin speed at 1400 rpm Max. load 6 kg With this programme it is possible to rinse and spin cotton garments which have been washed by hand. The machine performs 3 rinses, followed by a final long spin. Options Detergent Compartment SPIN RINSE HOLD EXTRA RINSE Important! The spin speed will automatically assume the setting for cotton items.
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
Removing stains Stubborn stains may not be removed by just water and detergent. It is therefore advisable to treat them prior to washing. Blood: treat fresh stains with cold water. For dried stains, soak overnight in water with a special detergent then rub in the soap and water. Oil based paint: moisten with benzine stain remover, lay the garment on a soft cloth and dab the stain; treat several times.
Drying Hints Preparing the drying cycle As a dryer, the appliance works on the condensation principle. Therefore, the water tap must be open and the drain hose must drain water into a sink or into the drain pipe, even during the drying cycle. Attention! Before starting the drying programme, reduce the loads of washed laundry, in order to obtain good performances.
er in order to activate the ECO valve. Then run a cotton cycle at the highest temperature without any laundry in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a measure of detergent into the main wash compartment and start the machine. Personalisation Acoustic signals The machine is provided with an acoustic device, which sounds in the following cases: • at the end of the cycle • if there is a fault.
Select the required programme by means of the programme selector dial (1) Turn the programme selector dial to the required programme. The green pilot light of button 7 starts to flash. The selector dial can be turned either clockwise or anticlockwise. to reset the Turn the selector dial to position programme/to switch the machine OFF. At the end of the programme the selector , to dial must be turned to position switch the machine off.
Important! • The selected delay can be changed only after selecting the washing programme again. • The door will be locked throughout the delay time. If you need to open the door, you must first set the washing machine to PAUSE by pressing button 7 and wait a few minutes before opening the door. After you have closed the door, press the same button again. Important! The Delay Start cannot be selected with the draining programme.
Use - Drying Drying only 6. Caution! The recommended load size is 3.5 kg for cottons and linen and 2 kg for synthetic items. 7. By pressing Drying Time button it is also possible to dry up to 5 kg of cotton items (see the «Drying Programme » table). Caution! The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe. 1. Load the laundry. 2.
If possible, do not select a spin speed lower than that proposed by the appliance to avoid too long a drying time therefore saving energy. 5. 6. 7. In any case the reduction of the spin speed is only possible after selecting drying. For cottons and synthetic the lowest value you can select is 900 r.p.m. Set the dryness degree by pressing button 3. The display shows the whole duration of the washing and the set drying cycle. Start the programme by pressing button 7.
Care and cleaning Warning! You must DISCONNECT the appliance from the electricity supply, before you can carry out any cleaning or maintenance work. Descaling The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine. Do this separately from any laundry washing, and according to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits.
Open the pump door. Put a container below the recess of the drain pump to collect the water that flows out. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. Press the two levers and pull forward the drainage duct to let the water flow out. 1 2 When the container is full of water, put the drainage duct back again and empty the container. Do steps 3 and 4 again and again until no more water flows out from the drain pump.
Cleaning the water inlet filters Important! If the appliance doesn't fill, takes long to fill with water, the starting button blinks yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked . To clean the water inlet filters: • Turn off the water tap. • Unscrew the hose from the tap. • Clean the filter in the hose with a stiff brush. • Screw the hose back onto the tap. Make sure the connection is tight.
1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. • : problem with the water supply. What to do if… Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
Problem Possible cause/Solution The machine does not empty and/or does not spin: The drain hose is squashed or kinked. • Check the drain hose connection. The drain filter is clogged. • Clean the drain filter. An option or a programme that ends with the water still in the tub or that eliminates all the spinning phases has been selected. • Select the draining or spinning programme. The laundry is not evenly distributed in the drum. • Redistribute the laundry.
Problem Possible cause/Solution Spinning starts late or the machine does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed in the drum, the machine will not spin.
If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... Technical data Dimensions Width Height Depth 60 cm 85 cm 63 cm Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate, on the inner edge of the appliance door.
Mount the rubber feet to prevent vibration, noises and displacement of the appliance during operation. Read carefully the instructions supplied with the kit. Water inlet Open the porthole, remove the polystyrene block fitted on the door seal and pull out all items from the drum. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. Positioning Install the machine on a flat hard floor.
Caution! The inlet hose must not be lengthened. If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use. Water drainage The end of the drain hose can be positioned in three ways: Hooked over the edge of a sink using the plastic hose guide. In this case, make sure the end cannot come unhooked when the machine is emptying. This could be done by tying it to the tap with a piece of string or attaching it to the wall.
132916430-A-052013 www.zanussi.
