REFRIGERATOR ZI 1450 INSTRUCTION BOOKLET 2222741-42
CONTENTS Instructions for the user Important Safety Instructions 3 Description of the Appliance 4 Use 5 Cleaning the interior Starting-up Temperature control Fresh food refrigeration Movable shelves Positioning the door shelves 5 5 5 5 5 5 Hints 6 Hints for refrigeration 6 Maintenance 7 Defrosting Periodic cleaning Periods of non-operation Interior light 7 7 7 7 Customer service and spare parts 8 Instructions for the installer 2 Technical specifications 8 Installation 8 Positioning E
IMPORTANT SAFETY INSTRUCTIONS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety.
DESCRIPTION OF THE APPLIANCE ➀ Butter shelves ➁ Shelves ➂ Bottle shelf ➃ Salad bin ➄ Shelves ➅ Thermostat ➆ Defrosting water tray ➇ Ice-cube production compartment ➇ ➀ ➅ ➆ ➁ ➄ ➃ ➂ 4
USE Cleaning the interior Fresh food refrigeration Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. The refrigerator compartment is suitable for cooling drinks and for normal food storing.
For more thorough cleaning, the top door shelves can be removed by pulling them in the direction of the arrows, then refitting them in position. D006 Ice cube production The refrigerator is equipped with one or more ice cube trays, which should be filled with drinking water and placed in the special compartment. Do not use metal implements to detach the trays. HINTS Hints for refrigeration To help you use your refrigerator correctly, here are some useful hints: Cooked food, cold cuts, jelly, etc.
MAINTENANCE Unplug the appliance before carrying out any maintenance operation. Interior light Defrosting The light bulb inside the refrigerator compartment can be reached as follows: 1. unscrew the light cover securing screws; 2. unhook the moving part as shown in the figure. During normal operation, the evaporator in the refrigerator compartment will gradually become covered with frost.
CUSTOMER SERVICE AND SPARE PARTS If the appliance is not functioning properly, check that: the plug is firmly in the wall socket and the mains power switch is on; To obtain fast service, it is essential that when you apply for it you specify the model and serial number of your appliance which can be found on the guarantee certificate or on the rating plate located inside the appliance, on the bottom lefthand side.
Door reversibility Instructions for building in under a worktop A Dimensions of the recess Height of housing Depth of housing Width of housing mm 702 mm 550 mm 560 600 702 20 560 min B D480 The appliance’s door has been locked in position for transport by means of pins on both sides. According to the door opening direction, remove relevant pins at the top (A) and at the bottom (B). min 200cm 2 550 min 20 560 min 50 D474 Instructions for building into a tall kitchen unit 1.
B A A C C D B PR266 D494 3. Push the appliance up against the kitchen unit on the side opposite the door hinge. The appliance is supplied with 2 brackets (C) for attachment to the side of the kitchen unit; fit these brackets as shown in the figure. 6. Separate parts A, B, C, D as shown in the figure. 50mm A 20m m E PR166 7. Place guide (A) on the inside part of the furniture door, up and down as shown in the figure and mark the position of external holes.
8mm A PR167 B 9. Open the appliance door and the furniture door at 90°. Insert the small square (B) into guide (A). Put together the appliance door and the furniture door and mark the holes as indicated in the figure. Remove the squares and drill holes with Ø 2 mm at 8 mm from the outer edge of the door. Place the small square on the guide again and fix it with the screws supplied. PR168 10. Should the lining up of the furniture door be necessary, use the clearance of slots.
