INSTRUCTION BOOKLET COOKER HOOD ZHC 925
Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http:\\www.zanussi.co.
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation • Child Safety Any installation work must be undertaken by a qualified electrician or a competent person.
YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Cooker Hood Controls The cooker hood functions are controlled by five push button switches located centrally in the control fascia. T1 T2 T3 T4 T5 T1 Turns the worktop lighting On and Off Turns the fan motor On and Off Decreases the fan speed Increases the fan speed Intensive fan speed with timed programme.
To Operate Select the required fan speed and light if required. The appliance can be installed to recirculate or extract contaminated air. The cooker hood is more effective when used in the extraction mode. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted.
MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel.
Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned or regenerated, and must be replaced when the Instensive speed LED T5 starts to flash, or at least once every 3 months. Attention: If, when used in the recirculation mode both the T2 and T4 LED indicator lights begin to flash simultaneously this indicates the both the charcoal filter needs replacing and the grease filters need cleaning.
SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Solution Symptom The cooker hood will not start • Check the hood is connected to the electricity supply. • Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively • The fan speed is set high enough for the task. • The grease filter is clean. • The kitchen is adequately vented to allow the entry of fresh air.
GUARANTEE CONDITIONS We, Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in product or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.
INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical information DIMENSIONS HEIGHT OF CANOPY: HEIGHT OF CHIMNEY:(UPPER SECTION) (LOWER SECTION) WIDTH OF CANOPY: DEPTH OF CANOPY: 71.5mm 215mm 728.
INSTALLING THE COOKER HOOD 2 S G A G B I C P P1 R Fig. 5 Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check that the wall to which the cooker hood is to be fitted for electric cables, water and gas pipes.
Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions.
Fitting the Wall Brackets 1 210 260 20 d = 948 min Fixing the first wall brackets No 2 Draw a horizontal line through the vertical approximately 1 or 2mm from the ceiling or from a line on the wall where the upper chimney stack will finish. Place the top edge of the bracket under the line on the wall aligning the centre of the bracket with the vertical line. If, the alignment is correct mark the centres for the key hole bracket fixing screws (not supplied) as illustrated in Fig. 7 - a.
Fitting the Canopy Hood Before starting to fix the canopy it will be necessary to adjust the support brackets S1 by turning the screws clockwise until the limit of the thread is reached as illustrated in Fig. 8. a- Hook the canopy onto the two 4.2x44.4mm screws1 fitted as described above and illustraed in Fig. 9. b- Using a screw driver and spirit level, adjust the screws S1 until the canopy is level. Once the canopy is level, tighten up the wall fixing screws to secure the canopy.
Note: The two venting grilles must not be fitted into the lower chimney (I) until the chimney has been installed. Extraction The charcoal filter is not required in this mode and should be removed. Ducting The ducting used must be 150mm (6ins), or 125mm (5ins) in diameter. If possible duct through the wall immediately above the canopy. For the best performance use the shortest possible duct run and the minimum number of bends.
Fitting the Chimney Stack 2 The chimney consists of two sections. The upper chimney measures 215mm and the lower chimney (with the holes for recirculation on either side) measures 728.5mm. S To fit the upper section (S) first expand the chimney slightly to allow it to be fitted over the brackets 2, and then secure the chimney stack to brackets using the four self tapping screws provided as illustrated in Fig. 12.
© Electrolux Household Appliances Limited 2001 4329620 03 - 010910
