EN User manual Hob ZGS782ICTX GB
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 7 8 8 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1
pliance or hot cookware. Do not let the electricity bonds tangle. Installation • You must read these instructions. The manufacturer is not responsible for any injury to persons and pets or damage to property caused by failure to obey these requirements.
– Cut off the mains cable where it connects with the appliance and discard it. – Flat the external gas pipes if there are fitted. – Speak to your local authorised facilities for disposal of your appliance. Installation Warning! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force.
not come in touch with mobile parts or they are not squeezed. Also be careful when the hob is put together with an oven. 1 Important! It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Important! Failure to ensure the correct assembly will cause leakage of gas. Important! Make sure that the gas supply pressure of the appliance obeys the recommended values.
Electrical Requirements Permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety the installation must be done by a qualified electrician (e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting [NICEIC]). The manufacturer declines any liability if these safety measures are not observed.
b) Space for connections A B Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
Symbol Description minimum gas supply Operation Ignition of the burner Warning! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame Always light the burner before you put cookware. To light the burner: 1. Turn the control knob counterclockwise to the maxi) and push it down. mum position ( 2. Keep the control knob pushed for approximately 5 seconds; this will let thermocouple to warm up.
Burner Diameters of cookware Rapid / Triple Crown 180 - 260 mm Semi-rapid 120 - 220 mm Auxiliary 80 - 160 mm Warning! Pots must not enter the control zone. Flame will heat up the control zone. Do not put the same pan on two burners. Warning! Make sure pot handles do not protrude over the front edge of the cooktop and that pots are centrally positioned on the rings in order to achieve maximum stability and to obtain lower gas consumption.
to prevent difficult lighting and check that the burner crown holes are not obstructed. Periodic maintenance Periodically speak your local Service Force Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. Cleaning of the spark plug This feature is obtained through a ceramic ignition candle with a metal electrode.
If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution to the problem yourself, speak your dealer or the local Service Force Centre. If you operated the appliance incorrectly, or the installation was not carried out by a registered engi1 neer, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period.
Electric supply: 230 V ~ 50 Hz 3 core flexible cable with non rewirable plug fitted with a 3 amp cartridge fuse Appliance class: 3 By-pass diameters Burner Ø By-pass in 1/100 mm 28 Category: II2H3+ Auxiliary Gas connection: G 1/2" Semi-rapid 32 Rapid 42 Triple Crown 56 Gas supply: G20 (2H) 20 mbar Gas burners NORMAL POWER REDUCED POWER NORMAL POWER NATURAL GAS G20 (2H) 20 mbar LPG (Butane/Propane) G30/G31 (3+) 28-30/37 mbar BURNER kW kW inj. 1/100 mm m³/h inj.
www.zanussi.
www.zanussi.
www.zanussi.
397179801-A-502011 www.zanussi.