GAS HOB ZGM 782 ITX INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB IE
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation z z z z z This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas Installations I.S.
Contents For the Installer For the User Important Safety Information 2 Instructions for the Installer 8 Description of the Hob 3 Important safety requirements 9 Operation 4 Installation 10 Maintenance and Cleaning 5 Building In 11 Something Not Working? 6 Electrical connections 12 Guarantee Conditions 7 Wiring Diagram 13 Fault Finding 13 Commissioning 15 Conversion from Natural Gas to LPG 15 This appliance complies with the following E.E.C.
Operation Hob burners ) To light a burner: z turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (Fig. 1, D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. z then, check the flame is regular and adjust it as required.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
YES Cast Iron Pan Supports The hob has cast iron pan supports. Take care when removing them. They are very heavy and could damage the hob or your kitchen furniture if you let them fall down. To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. When removing the pan supports, lift them up as shown in the diagram. Never turn the pan supports on the hinges, this could damage them. Wash the pan supports using hot soapy water.
Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk Customer Care Department ZANUSSI 55-77 High Street Slough Berkshire SL1 1DZ 08705 727727 (*) For Customer Service in the Republic of Ireland please contact us at the address below: ZANUSSI Electrolux Group (Ire) Ltd.
Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) 680 mm 510 mm Front Left Burner (auxiliary) Heat Input 1.0 kW (3413 BTU/HR) CUT OUT DIMENSIONS Width: Depth: Rear Right Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) 560 mm 480 mm Front Right Burner (rapid) Heat Input 3.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations. Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S.
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
Building In Building over a cupboard or drawer Building over a kitchen unit with door If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Seal a FO 0199 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. The manufacturer declines any liability should these safety measures not be observed. Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm.
Wiring Diagram A. IGNITOR SWITCH B. IGNITOR UNIT Fault Finding Brown PLUG (with cover removed) Earth Wire Green/Yellow Blue START Isolate appliance and carry out: A: Earth Continuity check. Neutral Wire Blue SOCKET (face view) ( ) E( ) FUSE Preliminary Electrical Systems Check N L Blue Brown Green Yellow YES NO Carry out: C: Polarity check. Has inlet fuse blown? NO YES Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation check.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN. Remove the control knob.
CUSTOMER CARE ZANUSSI 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705 727727 Long Mile Road Dublin 12 Republic of Ireland Tel: + 353 (0) 1 4090751 © Electrolux plc 2003 From the Electrolux Group. The world’s No.1 choice. 35687-8301 09/04 Grafiche MDM - Forlì The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use.