EN User manual Hob ZGL640TW ZGL640ITX GB
Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 5 5 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Technical information _ _ _ _ _ _ _ _ _ _ _ _ 12 Subject to change without notice.
• • • • • ble or plug (if applicable) can make the terminal become too hot. Make sure that a shock protection is installed. Use the strain relief clamp on cable. Make sure not to cause damage to the mains plug (if applicable) or to the mains cable. Contact the Service or an electrician to change a damaged mains cable. The electrical installation must have an isolation device which lets you disconnect the appliance from the mains at all poles.
• Provide good ventilation in the room where the appliance is installed. • Make sure that the ventilation openings are not blocked. • Use only stable cookware with the correct shape and diameter larger than the dimensions of the burners. There is a risk of overheating and rupture of the glass plate (if applicable). • Make sure the flame does not go out when you quickly turn the knob from the maximum to the minimum position.
Daily use Warning! Refer to "Safety information" chapter. Ignition of the burner Warning! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame Always light the burner before you put cookware. To light the burner: 1. Push and hold the spark generator button . 2. At the same time turn the control knob counterclockwise to the maximum position and push it down to light the burner. 3.
• When the liquid starts to boil, turn down the flame to barely simmer the liquid. Warning! Use pots and pans with bottom applicable to the dimension of burner. Do not use cooking vessels on the hotplate that overlap its edges. Warning! Make sure pot handles do not protrude over the front edge of the cooktop and that pots are centrally positioned on the rings in order to achieve maximum stability and to obtain lower gas consumption.
Removing the dirt: 1. – Remove immediately: melting plastic, plastic foil, and food containing sugar. – Stop the appliance and let it cool down before you clean: limescale rings, water rings, fat stains, shiny metallic discolorations. Use a special cleaner applicable for surface of hob. 2. Clean the appliance with a damp cloth and some detergent. 3. At the end rub the appliance dry with a clean cloth. The stainless steel can become tarnished if it is too much heated.
If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution to the problem yourself, speak your dealer or the local Service Force Centre. These data are necessary to help you quickly and correctly. These data are available on the supplied rating plate. • Model description ................. 1 • Product number (PNC) ................. • Serial Number (S.N.) ................. Use the original spare parts only.
However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m³ and 11 m³. If there are other fuel burning appliances in the same room, B.S. 5440 Part 2 Current Edition, should be consulted to determine the requisite air vent requirements. For appliances installed in the Republic of Ireland please refer to the NSAI- Domestic Gas Installation I.S. 813 Current Editions Table Four.
3. With a socket spanner 7 remove the injectors and replace them with the ones which are necessary for the type of gas you use (see table in "Technical Data" chapter). 4. Assemble the parts, follow the same procedure backwards. 5. Replace the rating plate (it is near the gas supply pipe) with the one for the new type of gas supply. You can find this plate in the package supplied with the appliance.
necessary to change the fuse, use a 3 amp ASTA-approved (BS 1362) fuse. A B To replace the connection cable use only H05V2V2-F T90 or equivalent type. Make sure that the cable section is applicable to the voltage and the working temperature. The yellow/green earth wire (B) must be approximately 2 cm longer than the brown (or black) phase wire (A).
Kitchen unit with oven A The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
Electric supply: 230 V ~ 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse 3 By-pass diameters Burner Ø By-pass in 1/100 mm II2H3+ Auxiliary 28 G20 (2H) 20 mbar Semi-rapid 32 Rapid 42 Gas connection: R 1/2 " Category: Gas supply: Appliance class: Gas burners NORMAL POWER REDUCED POWER NORMAL POWER NATURAL GAS G20 (2H) 20 mbar BURNER kW kW inj. 1/100 mm m³/h LPG (Butane/Propane) G30/G31 (3+) 28-30/37 mbar inj.
www.zanussi.
www.zanussi.
397195001-D-GB-202012 www.zanussi.